Question about 1999 Chevrolet Silverado 1500

3 Answers

Code for automatic door locks on 1999 Chevy silverado

Does anyone know how to disengage the automatic door lock feature that locks the doors when moving 15mph on a 1999 Chevorlet 1500 silverado.

Posted by on

  • raymond marcel Sep 02, 2012

    I was trying to get away from the dealer for known reasons.in my reserach i found that blue wire can be cut from the door module .just wondering if it would stop my controle of the sto door locks switch?Thank you any further informstiom in advances.Ray

×

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

You have to take it into the dealership for a 1999. the dealer needs to change the settings in the BCM (body control module). in 2000, the BCM came preprogrammed to allow the owner to change the door lock settings at home. unfortunately for a 1999, it has to be done at the dealership.

Posted on Jan 07, 2009

  • hy_69 Dec 22, 2010

    if i have the same problem... and my computer its reprogrammed for better performance/mpg... and i take it to the dealership.. will that erase the settings i have now and return it to factory settings????

×

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 26 Answers

Just cut that light blue wire at the brown plug. Nearest drivers door on brown plug. Wire you need is right beside a white wire, left side of this brown plug on BCM. Body Control Module. I put a simple switch in, on the dash. Cut the light blue wire off at a reasonable distance from BCM plug. (I UNPLUGGED THE BCM BROWN CONNECTOR FIRST) Ran a jumper wire from light blue to my switch. From switch, I ran a wire back into truck end of light blue wire.
How this works now: If I want to use power locks, I turn switch on, then press lock button on my door. If I want to use my keyless entry remote, I turn switch on before leaving truck, then use my keyless entry remote lock button. If I want to lock my doors while in the truck, I turn the switch on, and hit the lock button on the door.
enjoy.
PS... I installed my switch where fog light switch would have been if my truck had em. Just a tiny round on/off 12v switch.

Posted on Nov 08, 2012

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 67 Answers

Hi
you have to take it into the dealership for a 1999.

Posted on Jan 07, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the fix for auto door lock on my 2007 chevy silverado engage and disengage while driving on the freeway after the vehicle is warm


Try disengaging the "Auto Lock" feature in the Driver Information System when shifting in/out of Park and at a certain MPH. If that keeps it from doing it, you know the BCM Body Control Module is controlling the action. It could be it "thinks" it's unlocked when it not. May need to replace the power lock assembly. You could also try taking the battery cables off to reset the PCM/BCM. That may fix it too. Worst case, it is the BCM, and they are not cheap. Good Luck!

Feb 16, 2015 | 2007 Chevrolet Chevrolet Silverado 1500

1 Answer

How do I install a new exterior(drivers side) door handle on a 1999 Chevy silverado. Tools needed, etc.


take door panel off there is nuts holding handle on door and 2 rods one to lock and one to handle to open door

Jan 22, 2011 | 1999 Chevrolet Silverado 1500

1 Answer

1999 Chevy silverado z71trying to program a new key fob


Use this procedure for New Body Style.
1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).




Apr 29, 2010 | 1999 Chevrolet Silverado 1500

2 Answers

Remote Door Lock/Unlock will not work.


At first look, I would have guessed that your battery in the door opener was dead, but that is not the case. I suggest driving to a nearby Chevy dealer and ask one of the salesman if he/she can help. They have always been helpful to me. If not try another one as they are in business to sell not only cars, but service also. They will be your best bet to fixing it. :D

Jun 07, 2009 | 1999 Chevrolet Silverado 1500

2 Answers

Program fob


Instructions to program a keyless entry remote for a Chevy Silverado. They also work on 2003, 2004 and 2006 Suburbans.
  1. Close all the vehicle doors.
  2. Insert the ignition key into the ignition lock cylinder.
  3. Press and hold the DOOR unlock switch.
  4. While holding the DOOR lock switch in the unlock position, cycle the ignition ON, OFF, ON, OFF.
  5. Release the DOOR unlock switch. The doors will lock and unlock to confirm the program mode.
  6. Press and hold the LOCK button and the UNLOCK button simultaneously on one keyless remote. After a delay of approximately 15 seconds, the doors will lock and unlock to confirm the programming of that transmitter.
  7. Repeat the previous step to program up to four transmitters.
  8. Turn the ignition switch to the RUN (one more click forward) position in order to exit the keyless entry transmitter mode.
  9. Operate the transmitter functions in order to verify correct system operation

Apr 19, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

How to use slim jim


ok well first off do you know anyone that has a truck close to the same year if so try using there key it should work to open your door and on how to use a slim jim depends on if you have power locks or not if so it's a bit harder than if you don't but you put it between the window and the rubber seal and slip it under the door locking bar ether up and forword or back if its a manual lock and if not you haft to move the slim about 2 to 5 inches from the lock and do the same good luck

Apr 15, 2009 | 1999 Chevrolet Silverado 1500

1 Answer

2005 silverado door locks


i work at a chevy dealership,just had the same problem my fix was to replace the power door lock relay located on drivers side interior fuse block

Jan 21, 2009 | 2005 Chevrolet Silverado 1500 2WD

1 Answer

1999 DODGE DURANGO AUTOMATIC DOOR LOCKS.


That feature is called rolling locks.
In order to program the rolling door locks you will need to do the following procedure (listed on page 10 of the owners manual).
1. Close all of the doors.
2. Place the key in the ignition and cycle the key from the OFF to the ON position for a total of 4 to 5 times, ending in the ON position, do not start the engine.
3. Press the driver's side power lock switch to LOCK the doors within 30 seconds of cycling the key.
4. You will hear a single chime when programming is complete.
5. To cycle the feature on/off repeat the procedure.

Jan 11, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

1,008 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...