Question about 2001 Isuzu Rodeo
I am trying to install an after market radio and the wires are spliced so I am trying to figure out what the color code or the factory wire is. I have found a couple online and they didn't make anything work. Anyone have any ideas..
SOURCE: need factory wiring codes
2003 Chevrolet Silverado 1500 Car Radio Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Orange
Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. Run a wire to the fusebox for switched power.
Car Radio Ground Wire: Black/White
Car Radio Illumination Wire: Gray
Car Stereo Dimmer Wire: Brown
Car Stereo Antenna Trigger Wire: Pink
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: Under the center console.
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Tan
Left Front Speaker Negative Wire (-): Gray
Right Front Speaker Positive Wire (+): Light Green
Right Front Speaker Negative Wire (-): Dark Green
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown
Left Rear Speaker Negative Wire (-): Yellow
Right Rear Speaker Positive Wire (+): Dark Blue
Right Rear Speaker Negative Wire (-): Light Blue
If that dosnt match with your vehicle try this tip, 1st always find your speaker wires first,Since this is the most tedious part, its better to get those out of the way, 2nd thing Disconnect the battery of the vehicle so you don't blow fuses for the head unit, 3rd, strip back all of the wires that are available to you. Its better to grab the all together and cut them all an equal length to make it neat. 4th
Once you have all your wires stripped back - Grab any single wire. Hold it against a terminal on the battery and one by one go through and tap every other wire against the other terminal of the battery until you hear a "pop". When you hear a speaker popping, you have correctly identified the wires that run directly to it. If on the first attempt at popping a speaker you don't find one, pick up another wire and repeat the process. They will eventually come, and the more you identify, the fewer wires you have to mess with, You will need these Items,You'll need some wire strippers, a digital multimeter, electrical tape,9 volt battery
Posted on Oct 18, 2008
SOURCE: installing after market stereo
You will need to go buy a wiring harness adapter from your local Walmart (usually cheapest there) or Local Electronics place (ie Best Buy). The wire harness that goes out from the radio goes into the Adapter and the adapter plugs into the car harnesses. Also these Adapters come with the wiring diagrams for your vehicle. They typically run 10 - 15 bucks depending on where you get them. Thanks for using FixYa!
Posted on Nov 21, 2008
you're having the same problem i had with my 99 isuzu rodeo 2 wd 3.2 i paid a muffler guy over $600 to replace those catalytic converters, if you're good at welding you could do the welding yourself after buying the catalytics, basiclly i seen them just cut them off and welded them back on
Posted on Dec 31, 2008
The resistors are in circuit only on the lower fan speed settings.
On the highest speed setting, power is switched directly to the fan motor.
Check fan power supply fuses,
Check power is available to the fan when high speed selected.
If all above OK, apply power directly to the motor to verify fan motor runs- if it doesn't the motor may need replacement/repair.
Posted on Jul 29, 2009
Best thing to do is go to a junk yard find the same truck and take the wiring harness off of it.Then go to wallmart and for 15.00 you cna buy a kit that just snaps into place
Posted on Nov 02, 2009
Tips for a great answer:
Jan 27, 2015 | Cars & Trucks
May 05, 2014 | 2004 Chevrolet Impala
Mar 05, 2013 | 2006 Dodge Charger
Feb 16, 2013 | 1999 Chevrolet S-10 Pickup
Jun 07, 2012 | Lincoln Cars & Trucks
Aug 27, 2011 | 1991 Toyota MR2
Jan 22, 2011 | 1998 Cadillac Eldorado
May 23, 2010 | 1998 Dodge Ram 1500 4WD
Nov 22, 2009 | 1993 Isuzu Rodeo
1,420 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: