Question about 2003 BMW 325

1 Answer

1990 bmw 325i I need to remove the drivers door panel and can't get the door latch and mirror connector off. Can you help?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

The mirror connecter comes off with a small screwdriver lifting under the rubber it will pull right out. the latch comes off with the screws and you have to twist the handle you will see how it comes off.

Posted on Feb 16, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need help on removing door panel on 2000 Dodge Caravan - window fell in dorr and I can not seem to get the panel off. Any suggestions?


Answer
FRONT DOOR TRIM PANEL
REMOVAL
Using a trim stick (available from parts stores), pry courtesy lamp from door trim.
Disconnect wire connector from courtesy lamp.
If equipped, remove screws attaching door assist handle to inner door panel.
If equipped, remove screw attaching door pull cup to inner door panel.
If equipped, remove screws attaching trim panel to door from below map pocket.
If equipped, remove window crank.
Using a trim stick, remove screw cover from switch panel.
Remove screws attaching switch panel to door trim.
Remove power accessary switch from door trim Front Door Switch Panel
Disconnect power switch from wire connector.
If equipped, using a small, flat bladed pry tool, remove memory seat/mirror switch and disconnect wire connector Memory Seat/Mirror Switch
If equipped, remove screw holding door trim to door panel from behind inside latch release handle.
Disengage clips attaching door trim to door frame around perimeter of panel Front Door Trim Panel
Lift trim panel upward to disengage flange from inner belt molding at top of door.
Tilt top of trim panel away from door to gain access to latch linkage.
Disengage clip attaching linkage rod to inside latch release handle Inside Door Handle Linkage
Separate linkage rod from latch handle.
Remove front door trim panel from vehicle.
INSTALLATION
Hold top of trim panel away from door to gain access to latch linkage.
Place linkage rod in position on latch handle.
Engage clip to hold linkage rod to inside latch release handle.
Place front door trim panel in position on door.
Install trim panel into inner belt molding at top of door.
Install clips to attach door trim to door frame around perimeter of panel.
If equipped, install screw to attach door trim to door panel behind inside latch release handle.
If equipped, connect power switch into wire connector.
Place power accessary switch in position on door trim.
Connect wire connector into memory seat/mirror switch and install switch into trim panel.
Install screws to attach accessary switch panel to door trim.
Install screw cover into switch panel.
If equipped, install window crank.
If equipped, install screws to attach trim panel to door inside map pocket.
If equipped, install screw to attach door pull cup to inner door panel.
If equipped, install screws to attach door assist handle to inner door panel.
Connect wire connector into courtesy lamp.
Install lamp in door trim.

Feb 02, 2012 | 2000 Dodge Caravan

1 Answer

How to remove the in door of a 1990 bmw 325i? And also the drivers door will not lock when i turn the key the other doors lock but the drivers door doesnt how should i go about fixing that?


Sounds like you need to replace the power door lock actuator for the driver's door.


E30 Models
  1. Remove the door panel and the water shield.
  2. Disconnect the wiring from the actuator. Remove the screws and pull the actuator off the linkage.
  3. When installing, move the actuator and linkage to the locked position.
  4. Connect the linkage to the actuator and loosely install with the screws.
  5. Compress the actuator drive to take out any play in the linkage and tighten the screws.
  6. Test the locks and install the door panel.

E36 Models
  1. Remove the door panel and water shield.
  2. On the front doors, remove the guide rail nut and pull the guide rail down. Disconnect the wiring and the linkage from the actuator.
  3. On the rear doors, remove the window and the access panel. Disconnect the wiring and the linkage from the actuator.
  4. Remove the 3 bolts holding the latch and actuator to the door structure.
  5. Install in reverse order using threadlocker on the bolts.

Mar 16, 2011 | 2003 BMW 325

1 Answer

How do I remove the driver side door panel to replace window motor


1. Remove 2 small screws at bottom of the door panel (6mm)
2. Remove small black cover from inset for door handle (pry it out carefully with a small flat head screw driver or panel removal tool) and remove bolt behind it (8mm)
3. Pop window/door lock control panel out with the same flat head screw driver and disconnect all connectors. Remove small screw from behind it (6mm)
4. Lift straight up on door panel and then tilt toward you.
5. Disconnect mirror control connector.
6. Squeeze two tabs on the door latch assembly and it can be removed along with the cable. DONE.

Jul 02, 2010 | 1999 Ford F150 Regular Cab

1 Answer

How do I take off the drivers side door panel in a


a few hidden screws then pop the plastic plugs off the door with that special snap-on door panel removal tool.

Jun 02, 2010 | 1988 BMW 3 Series

1 Answer

I have a 1994 BMW 325i window has fallen into door


you dont need to take the door off just the casing u need a workshop manual it will aways come in handy

Apr 15, 2010 | 1994 BMW 3 Series

2 Answers

How do you remove the driver side door panel on a 2004 Jeep Cherokee.


- Remove trim plug from mirror flag bezel.
- Remove screws attaching trim panel to door
- Using a trim remover, detach trim panel perimeter push-in fasteners from door trim panel
- Lift trim panel upward and separate from door.
- If equipped, disconnect harness connectors for power accesories.
- Disconnect latch rods from inside handle actuator
- Finally, separate trim panel from vehicle.

I suggest check all information in the WJ Repair Manual Section 23 Body with graphics and other details.

Good luck (remember rated this help).


Feb 03, 2010 | Jeep Grand Cherokee Cars & Trucks

1 Answer

How to remove the inside door panel from a dodge 2005 2500 pick up


FRONT DOOR TRIM PANEL - REMOVAL
Release door latch and open door.
Roll window down.
Remove window crank Window Crank - Typical , if equipped.
Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
Disengage inside handle linkage rod from inside handle.
Disconnect speaker harness wire connector Speaker And Power Mirror Connector
Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
Separate door trim panel from vehicle.
INSTALLATION
Position trim panel at door.
Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
Engage power mirror wire connector, if equipped.
Connect speaker harness wire connector.
Engage inside handle linkage rod to inside handle.
Align trim panel retainer steps with inner door panel and slide trim panel into place.
Install screws attaching trim panel to door.
Install window crank, if equipped.

Hope helped with this; remember rated this help. Good luck.

Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

Door panel removal


  There is hidden screw under top of arm rest.  the mirror control comes out.  Be careful.  then there are 2 screws in bottom of arm rest.  Then the arm rest/handle needs to spin up towards sky and it will pull out.  the scushing (plastic around handle ) slides forward and this handle surround will come off.  Then there are clips that are behind panel.  Put hand between door and door panel and pull panel outward. be careful.  sometimes firm tug is better

Jan 01, 2009 | 2001 BMW 325

1 Answer

How to remove the driverside door panel 2001 325i


with a screw driver remove the mirror control, that comes off its another screw there i had the same problem

Nov 17, 2008 | 2001 BMW 325

Not finding what you are looking for?
2003 BMW 325 Logo

Related Topics:

204 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Fred Sops

Level 2 Expert

271 Answers

Al Clark

Level 2 Expert

290 Answers

Doberman

Level 2 Expert

246 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...