Question about 2008 Toyota Prius

1 Answer

Remove engine from toyota prius precautions

How do i go about disconnecting the inverter and wiring harness without messing something up?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 3 Answers

Try putting the engine back in and then refill the fuel tank with strawberry douch that should solve the proble you were havin in the first place. No need to remove engine.

Posted on Jan 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Do have to take off crank shafts pulley off to replace water pump on 97 Isuzu rodeo


wow the rare post that tells the job, waterpump off. bravo !
which engine? nobody ever posts, what engine they have,
you can log in and read it your self, on any car and engine
here
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

or ill guess engine,
so i guess
2.2L (chapter engine cooling, pump off)

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Radiator hose
    • Accessory drive belt
    • Front cover
    • Timing belt. Refer to the Timing Belt procedure.
    • Water pump
3.2/3.5L
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Negative battery cable
    • Upper radiator hose
    • Timing belt. Refer to the Timing Belt procedure.
    • Idler pulley
    • Water pump
now the timing belt.

2.2L
  1. Disconnect the negative battery cable.
  2. Disconnect PCV hose from cylinder head cover.
  3. Remove the air intake duct.
  4. Remove the left side ground cable from cylinder head cover and disconnect ground cable connector on the left side wheel arch. Remove right side ground cable from generator stay and disconnect ground cable connector on the right side wheel arch.
  5. Disconnect the 3 (black, green and blue colors) engine wire harness connectors from chassis harness of left rear side of compartment.
  6. Disconnect the cooling fan wire harness connector from cooling fan on left side top of fan shroud.
  7. Use a wrench to rotate the drive belt tensioner as shown to remove drive belt.
  8. Remove PCV hose from cylinder block.
  9. Remove intake duct stay from cylinder head.
  10. Remove two bolts for remove ignition cable cover from cylinder head cover.
  11. Disconnect ignition cable from ignition plug.
  12. Disconnect camshaft position sensor harness and crankshaft angle sensor harness from behind generator.
  13. Remove the 4 bolts, then remove the crankshaft pulley.
  14. Remove timing belt front cover.
  15. Loosen the timing belt rear cover bolts as shown in the accompanying figure, then remove the camshaft angle sensor.
  16. end cover off. (belt)
  17. Before servicing the vehicle, refer to the Precautions Section.
  18. Disconnect the negative battery cable.
  19. Using a box-end wrench on the drive belt adjuster, turn the adjuster clockwise and remove the drive belt.
  20. From the left rear of the engine compartment, disconnect the 3 electrical connectors from the chassis harness.
  21. Remove the crankshaft pulley-to-crankshaft bolts and remove the pulley.
  22. From the front of the engine, remove the nut and the engine harness cover.
  23. Remove the timing belt cover.
  24. Rotate the crankshaft to position the timing marks at Top Dead Center (TDC) of the No. 1 cylinder's compression stroke.


  25. Remove the timing belt tensioner adjusting bolt and the tensioner from the engine.
  26. Remove the timing belt.
bingo the belts off, pump is exposed.
now the 3.2. im going to skip the v6
but there is one step that varies, per your question , that pulley
Use tool No. J-8614-01, or a suitable pulley holding tool to remove the crankshaft pulley center bolt. Remove the crankshaft pulley.

righty tighty-lefty loosey, or RHT, right hand threads.

on the 3.2/3.5L v6 the center bolts comes off.
and this

Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs. (167 Nm).

if car is M/T we use 5th gear, to remove crank bolts
if car is A/T this is a pain, thus the tool above.
how to lock any A/T crank to achieve this is tricky.

show a nice list of ways, some work others dont.
depends on exact engine in question, not stated once.
fly wheel lock.
DIY tool on front bolts.


i usually just make my own tool, with angle iron
some use a chain wrench, (making a nice ugly mess)
Install the crankshaft pulley and tighten the pulley bolt to 123 ft. lbs.


so post back with engine size and trans type. so we can really help
above is wild guessing and to show tip of ice berg, timing belt issues, ever done one before on this engine? T belt??????
the v6 looks like this....on more wild guess.

25401255-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg

Feb 05, 2015 | 1997 Isuzu Rodeo

1 Answer

I have a 2002 toyota prius that will not start only code is p3030 what can I do to fix this I have cleard the code and as soon as I trun the key on it pops right back up


Error Code: P3030
Description: Disconnection between battery and ECU.

The battery ECU monitors a voltage of the battery blocks to detect an open malfunction in internal battery voltage sensor circuits of the battery ECU and the wire harness between each battery block and battery ECU. If a voltage at one of the battery blocks is below a standard level or of all the battery blocks is within a specified range, the battery ECU judges that there is an open in the internal sensor circuit(s) or wire harness. The battery ECU then illuminates the MIL and sets a DTC (Diagnostic Trouble Code).
Trouble Area:
- Junction Block Assembly (Bus Bar Module).
- Frame wire number 2, (Bus Bar and wire harness).
- Battery ECU.

Aug 09, 2014 | 2002 Toyota Prius

2 Answers

Toyota prius code P0A41


There is an open or short in motor resolver circuit
Check your connections
also check:
Wire harness or connector
Hybrid vehicle motor
HV control ECU

Jun 19, 2014 | 2006 Toyota Prius

1 Answer

2002 toyota prius warning light - car with exclamation mark


The light that looks like a car with an exclamation mark in the middle of it is the HYBRID WARNING light (see diagram below) You must scn the onboard computer network to determine why this light is coming on. You also need to scan your computer system to find out why the engine keeps dying. If the hybrid batteries are discharged, they must be properly recharged to prevent serious damage.

CAUTION: Read ALL service and warning lables in the engine compartment before attempting ANY type of service on a hybrid vehicle. The wiring harnesses that have ORANGE connectors are HIGH VOLTAGE connectors and can cause serious injury or death.

DO NOT touch any wiring harness or component that has a HIGH VOLTAGE warning label on it.

My recommendation is to tow the vehicle to a qualified hybrid repair center (preferably the dealer) and get it properly diagnosed and repaired. The high-tech, high voltage systems in this vehicle is nothing for anyone but a trained, certified technician to be messing with.


5_21_2012_12_29_44_am.jpg

May 20, 2012 | 2002 Toyota Prius

1 Answer

Where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

1 Answer

Trying to remove an alternator from an 06 altima


Removal and Installation L4-2.5L (QR25DE) Engines To Remove:
nis_alt_l4_alt.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Engine cover
    • Front/right-side engine undercover
    • Drive belt
    • Alternator harness connector
    • Engine ground wire from top mount
    • Alternator upper and lower mounting bolts
  3. Set the alternator aside and remove the top mount.
  4. Remove the alternator.
To Install:
nis_alt_l4_alt1.gif

  1. Slide alternator in place.
  2. Install or connect the following:
    • Alternator top mount
    • Alternator upper and lower mounting bolts
    • Engine ground wire from top mount
    • Alternator harness connector
    • Drive belt
    • Front/right-side engine undercover
    • Engine cover
    • Negative battery cable
V6-3.5L (VQ35) To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Drain coolant from the radiator into a suitable container.
  4. Remove or disconnect the following:
    • Radiator
    • Front/right-side engine under cover
    • Drive belt
    • Idler pulley
    • Alternator adjustable top mount
    • Alternator lower mount bolt and nuts
    • Alternator lower front bracket bolt
    • Alternator harness connectors
    • Alternator
To Install:
nis_alt_chg_v6.gif

  1. Install or connect the following:
    • Alternator in place
    • Alternator harness connectors
    • Alternator lower front bracket bolt
    • Alternator lower mount bolt and nuts
    • Alternator adjustable top mount
    • Idler pulley
    • Drive belt
    • Front/right-side engine under cover
    • Radiator
  2. Replace the engine coolant.
  3. Connect the negative battery cable.
  4. Start the engine and check for leaks.
  5. Recheck coolant level and top off as needed.
prev.gif next.gif

Oct 15, 2010 | 2006 Nissan Altima

1 Answer

How do i change the starter on a 2000 nissan altima


I hope this helps:

REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  4. Lightly lower the transmission to make room and pull out the dipstick tube.
  5. Remove or disconnect the following:
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  6. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
  7. Remove the transmission jack
    • Negative battery cable
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install or connect the following:
  3. Install the components in the reverse order of removal.
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle Fig. 1: Starter location and mounting detail — Maxima with a manual transaxle 89612g12.gif
    To install:
  2. Install or connect the following:
    • Starter
    • Starter attaching bolts. Tighten the long bolt to 57–72 ft. lbs. (77–98 Nm) and the short bolt to 22–30 ft. lbs. (30–41 Nm).
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
  3. Start the engine a few times to make sure of proper operation.
Altima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install the components in the reverse order of removal.
prev.gif next.gif

Jul 13, 2010 | 2000 Nissan Altima

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

Where is starter on 2002 honda crv?


Honda_Cr-V_2001-2006
Starter - Removal & Installation

2.0L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Starter wiring harness connectors Starter motor

To install:
  1. Install or connect the following:

    Starter motor. Tighten the bolts to 33 ft. lbs. (44 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 79 inch lbs. (9 Nm). Negative battery cable

2.4L Engine
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Knock sensor connector Starter wiring harness connectors Starter motor

    8b26da5.jpg
    Fig. Starter mounting

To install:
Install or connect the following:

Starter motor. Tighten the upper bolt to 33 ft. lbs. (44 Nm); the lower bolt to 47 ft. lbs. (64 Nm). Starter wiring harness connectors. Tighten the battery cable nut to 84 inch lbs. (9 Nm). Knock sensor connector Negative battery cable


Hope this help (remember comment and rated this).

Apr 04, 2010 | 2002 Honda CR-V

1 Answer

How to replace the starter


Toyota Celica, Corolla, ECHO & MR2 1999-05
Starter - Removal & Installation

1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Radiator upper support seal
Air cleaner
Engine under covers
Starter wiring
Starter

3. Installation is the reverse of removal. Torque the bolts to 28 ft. lbs. (37 Nm). Note that the bolts are 2 different lengths.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Battery and tray. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery.
Coolant reservoir
Reservoir hose from the radiator
Right side under cover
Wiring clamp
Wiring from the starter
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring and nut
Starter connector and wire clamp
Right side engine cover
Radiator reservoir and hose
Battery and tray

2. Check the cooling system and top off if necessary.


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable. On models equipped with an air bag, work must NOT be started until at least 90 seconds have passed from the time that both the ignition switch is turned to the LOCK position and the negative cable is disconnected from the battery
Engine under covers
Wiring from the starter terminals
Starter mounting bolts
Starter


To install:
1. Install or connect the following:
Starter
Starter wiring
Engine under covers


1. Before servicing the vehicle, refer to the Precautions section.
2. Remove or disconnect the following:
Negative battery cable
Front engine undercover
Starter wiring harness connectors
Starter mounting bolts
Starter motor


To install:
1. Install or connect the following:
Starter motor. Tighten the bolts to 28 ft. lbs. (37 Nm).
Starter wiring harness connectors
Front engine undercover
Negative battery cable

Hope help with this (remember rated and comment).

Mar 11, 2010 | 2003 Toyota Corolla

Not finding what you are looking for?
2008 Toyota Prius Logo

Related Topics:

266 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6880 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...