Question about 2002 Chrysler Town & Country

1 Answer

2002 Chrysler Town and Country limp mode

Hello StormStrikes,
You gave me the good advice to make sure the the TCM is getting enough battery power to get the vehicle out of limp mode. I fully charged the battery and also made sure that there is a clean connection from battery terminals and cables. Still in limp mode and the code 1684 is still showing up. Not sure what to do at this point. Do you have anyother suggestions sir? I appreciate you for taking time helping!!!

Posted by on

  • truckerjobs Feb 03, 2009

    I changed the solenoid pack and now I have no problems at all. It fixed the problem!!! woo hoo. I payed $170 for the part and it took me about 2.5 hours to complete the job. I was able to do all the work from on top. The only time I had to get under the car is with a hammer hitting upward against the old solenoid pack to get it lose after the 3 bolts were taken out. If you have any questions, just let me know Dave.

    Thanks Robert

  • Anonymous Mar 23, 2014

    changed trainy and tcm still in limp mode and same readout codes

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 3 Answers

Hello, I have the same problem with my 2002 neon. I was told it was the solenoid pack. I purchased one on eBay (the garage want around $200) for $88. I also bought on eBay the input and output VSS(vehicle speed sensors) for $25 for both. Autozone has these sensors for $27 each. I am going to replace these parts in a day or so to see if it helps.I dont have a garage and its cold outside here in West Virginia. I have also been told to check the ground straps to make sure they are getting good connections. They are located at the starter. I will let you know how this turns out for me when I do the repairs. I have been reading many forums where others are having the same problems. If you have learned anything from your experience please let me know.
Thank you,Dave

Posted on Feb 03, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

P0888 code after i changed pcm why


Here is the definition for the code. The problem could be the relay or the harness.

P0888 CHRYSLER Description The Transmission Control Module (TCM) has detected less than 3 volts at the Transmission Control Relay output circuit
Read more: http://engine-codes.com/p0888_chrysler.html#ixzz2982gmkin

Oct 11, 2012 | 2003 Chrysler Town & Country

1 Answer

What is wrong here?


P0700 indicates that there are codes stored in the TCM. You need to scan the TCM for the actuall transmission trouble codes. This can only be done with a higher end scan tool to do this.

Aug 25, 2012 | 2001 Chrysler Town & Country

1 Answer

I have a 2001 Chrysler T&C. The transmission is stuck in limp mode. I have replaced the TCM and it is still in limp mode. I see manys postings with this problem but nobody posts what they did to repair...


Many times on Chrysler products, one or both of the speed sensors screwed into the front of the transmission will fail, and cause the tcm to go to limp mode. Also make sure you have power to the tcm. Someone with a scanner can check these for you, or the speed sensors are less than 20 bucks each, replace them both and cross your fingers. If the transmission has internal problems, the tcm will sense this and go into limp-mode as well.

Sep 04, 2011 | Chrysler Town and Country Cars & Trucks

1 Answer

What is limp mode?


Hi, limp mode or (limp-in mode or limp-home mode)occurs when your computer in your car is not communicating with the sensors on your engine. On some cars(volkswagon Passat for example) If you disconnect the battery then the computer will lose all of the settings and will go into limp-in mode.
The car will have little power and a top speed of only about 30 miles per hour.
The function of limp-in mode is to get you to a place that can repair the car but the car is barely drivable.

Jul 23, 2011 | 2002 Chrysler Town & Country

2 Answers

96 chrysler town country wont shift into third gear


If it starts out in 2nd gear & dosn't shift, it is probably in a limp in mode. the system will need to be diagnosed & computer satisfied. sometimes disconnecting the battery will reset the computer & allow the trans to shift untill it sees the problem again. I recomend getting the codes read first so the memory will not be erased.

May 21, 2011 | 1996 Chrysler Town & Country

1 Answer

My trans is stuck in second gear. Is that what


The town and country vans are know for transmission problems and it would not be stuck in 2nd gear if it was in limp mode. Limp mode typically controls the engine. I have seen people do a transmission flush/filter and add lucas to temporary fix the problem. There is also a good chance that the transmission has a solenoid problem preventing it from shifting into any other gears but second. Hope this helps!

Jul 30, 2010 | 2002 Chrysler Town & Country

1 Answer

2002 Chrysler Town & Country Alternator Replacement


YOU NEED TO BUY REPAIR MANUAL.IT WILL SHOW AND TELL YOU HOW TO REMOVE ALTERNATOR.

Jan 22, 2010 | 2002 Chrysler Town & Country

1 Answer

My chrysler 2002 town and country will not change gears. The RPMs stay at 2 or 3 when going 40 mph. What do I do?


I have the same vehicle, is your engine light on or flashing? Put your key in the ignition, turn back and forth 3 cycles of on off. End in the on position. If you have a 0700 code come up, your transmission is "done". Sounds like it is in "limp mode". Thats what happened to me. Had tranny overhauled, $1800.

Jan 21, 2010 | 2002 Chrysler Town & Country

2 Answers

Won't shift into high gear


po700 is the code in the pcm,telling you there is a code in the tcm( trans control module) po605 is a internal tcm error replace and program the trans control module

Sep 01, 2009 | 2002 Chrysler Town & Country

2 Answers

2002 chrysler town and country wont leave limp mode


try getting a new shift solenoid for it. i had the same problem on my 2002 chrysler town and country and my plymouth breeze which is also a dodge product. it is very simple to do and doesnt take all that long. the part will probably run you about 150 to 200 dollars but it should fix your problem.

Dec 31, 2008 | 2002 Chrysler Town & Country

Not finding what you are looking for?
2002 Chrysler Town & Country Logo

620 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

chargerhp
chargerhp

Level 3 Expert

813 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...