Question about 1993 Toyota Pickup

1 Answer

1993 TOYOTA PICKUP (V6) TEMPERATURE PROBLEM

My 1993 Toyota pickup (v6) has a temp problem. It seems to warm up good (good cab heat) but the temp gauge does not go up very much. Then when I drive it, it does not shift to 4th gear until it gets driven for some time. It looses some temp (looking at the gauge) and down shifts back to 3rd until the temp comes back some! Is there a tranny temp sensor? If so, where is it located? Or is it the engine temp sensor? (location)? I also have the speedo (not working) problem now! thanks. Paul.

Posted by on

  • Anonymous Mar 25, 2014

    i did not see

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 42 Answers

The trans will not allow overdrive until coolant reaches roughly 180 degrees, if the guage shows cool and the trans is not upshifting, or downshifts to third while driving. the problem is either a sticking (or missing) thermostat. follow the lower radiator hose to the engine and find the three 12mm nuts, remove these to get to it. a new toyota t-stat will have a little bleed valve on its face. position it upwards when installing. hope this is helpful.
P.S. Happy New Year





Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the starter solenoid on a 1994 Toyota pickup. V-6 2 wheel drive. Is it on the passenger side close to the cab.


I think you'll find that the solenoid is part of the stater assembly itself. If the V6 is anything like the 4 it isn't especially fun to remove the assembly.
http://www.ncttora.com/fsm/1993/starting.html

Jun 20, 2011 | 1994 Toyota Pickup

1 Answer

Diagram to install alternator belt on 1993 toyota pick up truck


Click on the following free direct Link. It has the correct Serpentine and Drive Belt Diagrams for your 1993 Toyota Pickup, with either the 2.4L SOHC In-Line 4-Cylinder, 2.7L DOHC In-Line 4-Cylinder, or 3.0L SOHC V6 Engine with the different Engine Options (AC/No AC etc.).

Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!


http://www.2carpros.com/car_repair_information/year/1993/make/toyota/model/pickup/1993_toyota_pickup_drive_belt_routing_diagram.htm

Mar 29, 2010 | 1993 Toyota Pickup

1 Answer

I have a 1990 toyota pickup DLX ext cab V6 5-speed


If it seems to run well otherwise, you might have a partially obstructed catalytic convertor. Usually if this is the problem, the engine will also bog down even if you try to rev it up when it is in neutral.

Feb 25, 2010 | 1990 Toyota 4Runner

1 Answer

1991 Toyota extra cab v6 manual tranny. starts


sounds like you have to adjust your idle, fuel injected or carburated?

Aug 10, 2009 | 1991 Toyota Pickup

1 Answer

1993 Toyota Pickup 3.0 V6 Vaccumn Lines diagram


Thanks for asking for my assistance!
Always here, my friend.
I still have your e-mail address; I will shoot you a .pdf is 2 minutes; 1993 3.0 V6, Da?

Oct 09, 2008 | 1993 Toyota Pickup

Not finding what you are looking for?
1993 Toyota Pickup Logo

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...