Question about 1995 Isuzu Trooper

1 Answer

I need to know where on the engine block the oil pressure sensor is located on a 95 Isuzu Trooper

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

You can look on autozone web site and look on repair info. Here is what it says it's located. Hope this helps.

Under hood, driver side, lower engine area, above oil pan, mounted in block I need to know where - clearpixel.gif clearpixel.gif clearpixel.gif

Posted on Jan 01, 2009

1 Suggested Answer

lebones337
  • 152 Answers

SOURCE: oil pressure sensor location

drivers side right above the oil pan

Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

1999 Isuzu trooper oil gauge jumping on and off and lose of power when it is happening


check the connection/wires on the oil pressure sensor
this unit reports a loss of oil pressure to the ECM which will turn off the engine
a faulty connection makes it report intermittently
all this if you have no unusual noises from the engine

Oct 25, 2016 | 1999 Isuzu Trooper

1 Answer

Oil pressure warning light does not lights.car running good.toyota sienna 1999 3.0 engine 6 cylinders


the light only comes on when the oil is low. to test it, next time you service it start the engine with a few quarts oil missing. it is safe for a short time, check the light

Apr 12, 2013 | 1995 Isuzu Trooper

1 Answer

I have a 95 Isuzu Trooper 3.2 DOHC. It just stopped running. Turns over have checked gas pressure seems fine. Thinking it's the crank shaft sensor. Where's it located.


Location is lower right side of engine block. ,you also have to remeber you have the famous ICM (ignition control module) This connector is famous for loose or corroded terminal, its located behind ICM at the intake manifold.wiggle it see if that will help to get it started,wiggle the connector you crank have your brother wiggle the wire to ICM and even the cranksensor wire3_29_2012_7_48_46_am.jpg3_29_2012_7_50_46_am.jpg

Mar 28, 2012 | 1995 Isuzu Trooper

1 Answer

ISUZU TROOPER 3L injectors, what oil pressure do they require to make them work


at cranking the oil pressure has to be approx 5 mPa before they start to work electrically also, oil pressure at rail varies from 4 to 28 mPa. on Tech2 scanner in data list rail oil pressure should be close to desired and when engine not running sensor should read 0 - 0.2 mPa if higher or a negative value when engine not running this indicates problem with rail oil pressure sensor which is a common problem.

Dec 28, 2010 | 2000 Isuzu Trooper

1 Answer

95 rodeo coolant problems


it could be leaking somewere else , get your cooling system pressure tested at a shop

Mar 07, 2009 | 1995 Isuzu Trooper

1 Answer

Isuzu trooper engine stops while driving


If its the 3.0 diesel it could be the rail oil pressure sensor starting to pack up .

Jan 21, 2009 | 1999 Isuzu Trooper

1 Answer

Oil pressure sensor location


drivers side right above the oil pan

Jan 01, 2009 | 1995 Isuzu Trooper

Not finding what you are looking for?
1995 Isuzu Trooper Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...