Question about 2000 Audi A6

1 Answer

How do i tighten power steering belt on audi a6 1997 model

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 29 Answers

You cant, it has a spring loaded serpentine belt tensioner that keeps the belt tight.

Posted on Feb 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the power steering belt on a 4g13



ADJUSTMENT

Excessive belt tension will cause damage to the alternator and water pump pulley bearings, while, on the other hand, loose belt tension will produce slip and premature wear on the belt. Therefore, be sure to adjust the belt tension to the proper level.
To adjust the tension on a drive belt, loosen the adjusting bolt or fixing bolt locknut on the alternator, alternator bracket or tension pulley. Then move the alternator or turn the adjusting bolt to adjust belt tension. Once the desired value is reached, secure the bolt or locknut and recheck tension.


REMOVAL & INSTALLATION

1.5L, 1.6L, 1.8L, 2.0L and 2.4L Engines


0900c15280037bf7.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 1.5L, 1.6L, 1.8L, 2.0L and 2.4L engines
Alternator Belt


0900c15280037bf8.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Loosen the adjuster lock bolt . . .


0900c15280037bf9.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the alternator belt from the engine

  1. Loosen the alternator support nut.
  2. Loosen the adjuster lock bolt.
  3. Rotate the adjuster bolt counter clockwise to release the tension on the belt.
  4. Remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the adjuster bolt clockwise until the proper tension is reached.
  3. Tighten the adjuster lock bolt and the alternator support nut.

POWER STEERING BELT


0900c15280037bfa.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. After the adjusting and fixed bolts are loosened, rotate the pump . . .


0900c15280037bfb.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. . . . then remove the power steering belt from the engine

  1. Remove the alternator belt as described above.
  2. Loosen the power steering pump adjusting bolts.
  3. Remove the power steering pump fixed bolt on the rear of the bracket.
  4. Rotate the pump toward the engine and remove the belt.

To install:
  1. Install the belt on the pulleys.
  2. Rotate the pump until the proper tension is reached.
  3. Tighten the adjusting bolts on the pump.
  4. Tighten the fixed bolt on the rear of the bracket.
  5. Install the alternator belt.

A/C COMPRESSOR BELT
  1. Loosen the tension pulley and remove the belt.
  2. The installation is the reverse of the removal.

3.0L DOHC, 3.0L SOHC Galant, and 3.5L Engines


0900c15280037bfc.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Serpentine belt routing-Mitsubishi 3.0L engines (except 1998-00 Galant models)


0900c15280037bfd.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Accessory V-belt routing-Mitsubishi 3.5L and 1998-00 3.0L SOHC Galant engines
ALTERNATOR AND A/C COMPRESSOR

  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the front undercover.
  2. Loosen the tension pulley fixing nut and relieve the tension on the belt by turning the adjusting bolt.
  3. Remove the belt.

To install:
  1. Install the belt on the crankshaft and alternator pulleys.
  2. Using the adjusting bolt on the tensioner, tighten the belt to the desired tension.
  3. Tighten the fixing nut to hold the adjustment.
  4. Install the undercover and lower the vehicle to the floor.
  5. Connect the negative battery cable.

POWER STEERING BELT
  1. Disconnect the negative battery cable.


CAUTION Wait at least 90 seconds after the negative battery cable is disconnected to prevent possible deployment of the air bag.
  1. Raise and safely support the vehicle and remove the undercover.
  2. Remove the alternator and A/C compressor belt.
  3. Lower the vehicle and remove the cruise control pump link assembly.
  4. Place the power steering hose under the oil reservoir.
  5. Loosen the tension pulley fixing bolts and remove the power steering pump drive belt.

To install:
  1. Install the power steering pump drive belt.
  2. Insert an extension bar or equivalent into the opening at the end of the tension pulley bracket and pivot the pulley to apply tension to the belt.
  3. Tighten the fixing bolts.
  4. Raise the vehicle and install the alternator and A/C compressor belt.
  5. Install the undercover and lower the vehicle.
  6. Connect the negative battery cable.

3.0L SOHC Diamante
  1. Disconnect the negative battery cable.
  2. Loosen the lockbolt on the face of the A/C tensioner pulley.
  3. Turn the adjusting bolt of the A/C tensioner pulley to loosen the tension of the A/C belt.
  4. Remove the A/C compressor belt.
  5. Loosen the locknut on the face of the power steering/alternator tensioner pulley.
  6. Turn the adjusting bolt of the tensioner pulley to loosen the tension of the belt.
  7. Remove the power steering/alternator belt.

To install:
  1. Install the power steering/alternator belt first and then the A/C compressor drive belt.
  2. Adjust the belts to the proper tension by turning the adjusting bolts and tighten pulley fixing nut/bolt.
  3. Tighten the mounting nut of the power steering/alternator tensioner pulley to 36 ft. lbs. (50 Nm).

Mar 21, 2013 | 1996 Mitsubishi Mirage

1 Answer

How do you change a power steering belt


Loosen the bolts that attach the power steering pump to the bracket. then push the pump down. this should make the belt loose enough to get off. then put the new belt on. take a pry bar and stick between the motor and the power steering pump through the top. push on the pry bar to raise the power steering pump and tighten the belt. while pushing on the pry bar to keep tension on the belt tighten the bolts that you loosened and you've changed your power steering belt. this can be done by one person, but it's a lot easier with two.

Aug 24, 2011 | Dodge Stratus Cars & Trucks

1 Answer

I have an 1997 Audi A4 1.8 SE. Towards the end of a long motorway drive the power steering failed, a few miles on from there the engine started overheating and both the coolant and then the battery light...


CHECK FOR BROKEN LOOSEN DRIVE BELT.IF DRIVE BELT BROKEN YOU WILL LOSE POWER STEERING, WATER PUMP AND ALTERNATOR STOP TURNING IF LOSE DRIVE BELT. IF DRIVE BELT BROKEN.CHECK FOR FAULTY DRIVE BELT TENSIONER.LOOK FOR SEIZED WATER PUMP, ALTERNATOR OR POWER STEERING PUMP.REASONS DRIVE BELT BREAKS.

Jun 07, 2011 | 1997 Audi A4

1 Answer

Serptine belt diagram


q4073a.gif



Belt Installation, Aerostar 4.0L Engine


q1815e.gif


Item Part Number Description 1 8620 Drive Belt 2 N606068 Bolt 3 10300 Generator 4 10153 Generator Mounting Bracket 5 8509 Water Pump Pulley 6 6B209 Drive Belt Tensioner 7 N800199 Screw 8 8678 Belt Idler Pulley 9 N802096 Screw 10 19703 A/C Compressor 11 2882 A/C Compressor Mounting Bracket 12 3C718 Brace 13 N806020 Bolt 14 3A674 Power Steering Pump 15 3A733 Power Steering Pump Pulley 16 N800199 Screw 17 N606572 Bolt 18 N620481 Nut 19 8501 Water Pump 20 6312 Crankshaft Pulley A - Belt Tension Check (See Specifications) B - Tighten to 40-55 Nm
(30-41 Lb-Ft) C - Tighten to 24-30 Nm
(18-23 Lb-Ft) D - Tighten to 21-29 Nm
(15-21 Lb-Ft) E - Tighten to 40-50 Nm
(30-37 Lb-Ft)

Belt Installation, Ranger and Explorer 4.0L Engine


q4082b.gif


Item Part Number Description 1 8620 Drive Belt 2 10300 Generator 3 8678 Belt Idler Pulley 4 19703 A/C Compressor 5 3A733 Power Steering Pump Pulley 6 8501 Water Pump 7 6312 Crankshaft Pulley 8 6B209 Drive Belt Tensioner 9 N806020 Bolt 10 2882 A/C Compressor Mounting Bracket 11 3A674 Power Steering Pump 12 N606572-S2 Bolt 13 N800199-S8M Bolt 14 N620481-S2 Nut 15 3C718 Brace 16 N606068 Bolt 17 10153 Generator Mounting Bracket 18 8509 Water Pump Pulley 19 N605805-S2 Bolt A - Belt Tension Check (See Specifications) B - Tighten to 21-29 Nm
(15-21 Lb-Ft) C - Tighten to 40-55 Nm
(30-41 Lb-Ft)

Belt Installation, Ranger 2.3L Engine


q3646c.gif


Item Part Number Description 1 8678 Belt Idler Pulley 2 10300 Generator 3 8509 Water Pump Pulley 4 3A733 Power Steering Pump Pulley 5 2E884 A/C Clutch Pulley 6 6312 Crankshaft Pulley

Belt Installation, Aerostar 3.0L Engine


q4740a.gif


Item Part Number Description 1 10300 Generator 2 3F671 Belt Idler Pulley 3 3A733 Power Steering Pump Pulley 4 6B209 Drive Belt Tensioner 5 6312 Crankshaft Pulley 6 8509 Water Pump Pulley 7 19703 A/C Compressor 2010&c18=modelyear&c35=wsm%2cdrive%20belt%20replacement%2cssk%2c03-05%2cremoval%20and%20installation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=405&ct=lan&hp=n&[aqe]

Mar 07, 2011 | 1995 Ford Aerostar

1 Answer

How do u change a serpentine belt for a 1999 ford escort zx2


ADJUSTMENT 1.8L Engines ALTERNATOR AND WATER PUMP BELT
  1. Loosen the alternator adjusting bolt.
  2. Raise and safely support the vehicle.
  3. Loosen the alternator mounting bolt. NOTE: Do not pry against the stator frame. Position the prybar against a stronger point, such as the area around a case bolt. Fig. 1: A belt tension gauge should be placed on the longest span of the belt to check tension — 1.8L engine 90981g05.gif

  4. Position a suitable belt tension gauge on the longest accessible span of belt and tighten the belt.
  5. Adjust the tension to 86–103 lbs. (383–461 N) for a new belt or 68–86 lbs. (304–383 kg) for a used belt.
  6. If a belt tension gauge is not available, adjust the tension to 0.31–0.35 in. (8–9mm) deflection for a new belt or 0.35–0.39 in. (9–10mm) deflection for a used belt.
  7. Tighten the alternator adjusting bolt to 14–19 ft. lbs. (19–25 Nm).
  8. Tighten the alternator mounting bolt to 27–38 ft. lbs. (37–52 Nm).
  9. Lower the vehicle. Fig. 2: Alternator and water pump pulley belt routing — 1.8L engine 90981g06.gif
POWER STEERING PUMP BELT
  1. Raise and safely support the vehicle.
  2. Loosen the power steering pump mounting bolt and nuts.
  3. Adjust the power steering pump and, if equipped, the air conditioning compressor belt tension by turning the pump adjusting bolt. Fig. 3: Power steering pump belt routing and locations of the mounting bolts, nuts and adjusting nut — models without A/C 90981g07.gif

  4. Tighten the power steering pump mounting nut near the pump adjusting bolt.
  5. Position a suitable belt tension gauge on the longest accessible span of belt and tighten the belt.
  6. Adjust the tension to 110–132 lbs. (491–589 N) for a new belt or 95–110 lbs. (422–491 N) for a used belt.
  7. Check for proper belt deflection. For a new belt (one with less than 10 minutes of run time), the deflection should be 0.31–0.35 in. (8–9mm). For a used belt (one with more than 10 minutes of run time), the deflection should be 0.35–0.39 in. (9–10mm).
  8. Tighten the power steering pump mounting nut, located near the adjusting bolt, to 27–38 ft. lbs. (37–52 Nm).
  9. Tighten the pump mounting bolt behind the pulley to 27–40 ft. lbs. (36–54 Nm), and the remaining pump mounting nut to 23–34 ft. lbs. (31–46 Nm).
  10. Lower the vehicle. Fig. 4: Power steering pump belt routing and locations of the mounting bolts, nuts and adjusting nut — models with A/C 90981g08.gif
1.9L Engines The accessory drive belt for 1.9L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner. NOTE: Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension. Fig. 5: Drive belt routing — 1.9L engines 86751052.gif
2.0L Engines The accessory drive belt for 2.0L engines has no provision for manual belt adjustment, since these engines use an automatic belt tensioner. Drive belt slack is taken up by the automatic tensioner. NOTE: Movement of the automatic tensioner assembly during engine operation is not a sign of a malfunctioning tensioner. This movement is the tensioner self-adjusting and is required to maintain constant belt tension. The belt tensioner has a belt length indicator. If the indicator marks are not between the MIN and MAX marks, the belt must be replaced. Fig. 6: Drive belt routing — 2.0L SOHC engine with A/C 90981g23.gif
Fig. 7: Drive belt routing — 2.0L SOHC engine without A/C 90981g24.gif
Fig. 8: Drive belt routing — 2.0L DOHC engine 90981g25.gif
prev.gif next.gif

Jul 16, 2010 | 1999 Ford Escort

1 Answer

Removing power steering pump from v8 windsor


Section 11-02A: Steering Pump, Power, C-II 1996 Aerostar, Ranger and Explorer Vehicles Workshop Manual REMOVAL AND INSTALLATION Pump and Pulley SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Steering Pump Pulley Remover T69L-10300-B Steering Pump Pulley Replacer T65P-3A733-C
Removal
  1. Disconnect the power steering return hose (3A713) at the pump and drain fluid.
  1. Remove the power steering pressure hose (3A719) by unscrewing connector from the pump.
  1. On the Aerostar 3.0L V-6 engine (6007), loosen the drive belt tensioner (6B209) and adjustment bolts.





    Item Part Number Description 1 10346 Generator 2 8501 Water Pump 3 8678 Belt Idler Pulley 4 3A733 Power Steering Pump Pulley 5 6303 Crankshaft 6 2884 A/C Clutch 7 — Without A/C On the 2.3L I-4 and 4.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a counterclockwise direction. On Ranger 3.0L V-6 engines, slacken belt tension by lifting drive belt tensioner in a clockwise direction. Remove drive belt (8620) from under drive belt tensioner and slowly lower pulley to stop. Remove the drive belt from the power steering pump pulley (3A733).





    Item Part Number Description 1 10346 Generator 2 2884 A/C Clutch 3 3A733 Power Steering Pump Pulley 4 8501 Water Pump 5 6303 Crankshaft 6 8678 Belt Idler Pulley 7 6B209 Drive Belt Tensioner
  1. NOTE: If the drive belt requires servicing, refer to Section 03-05 .

    Remove the drive belt from the power steering pump pulley.
  1. Remove the oil dipstick tube.
  1. Remove the power steering pump support (3C511).
  1. Install Steering Pump Pulley Remover T69L-10300-B on the pulley.
  1. NOTE: Do not apply pressure on the power steering pump rotor shaft (3B559). Pressure will damage internal thrust areas of the power steering pump (3A674).

    While holding the remover tool nut stationary with a wrench, rotate the inner spindle of the remover tool clockwise until the pulley is pulled off the power steering pump rotor shaft.
  1. Remove the bolts attaching the power steering pump to the A/C compressor mounting bracket (2882).
Installation
  1. Install the power steering pump on the A/C compressor mounting bracket. Install and tighten attaching bolts to 41-61 Nm (30-45 lb-ft). On 4.0L engine, tighten to 47-64 Nm (35-47 lb-ft).
  1. Position the support on the A/C compressor mounting bracket. Install mounting bolts and tighten to 47-64 Nm (35-47 lb-ft).
  1. NOTE: Fore/aft location of power steering pump pulley on power steering pump rotor shaft is critical. Incorrect belt alignment may cause drive belt squeal or chirp. Make sure pull-off groove on power steering pump pulley is facing front and flush with end of shaft ± 0.254mm (± 0.010 inch).

    Install the Steering Pump Pulley Replacer T65P-3A733-C and install the power steering pump pulley.
  1. Install the drive belt on the power steering pump pulley.
  1. On the 2.3L I-4, Ranger 3.0L V-6, and 4.0L V-6 engines, position and rotate drive belt on engine. While lifting drive belt tensioner in a counterclockwise direction (clockwise on Ranger 3.0L V-6), slide drive belt under drive belt tensioner and lower drive belt tensioner to drive belt.
    On Aerostar 3.0L V-6 engine, position the belt idler pulley (8678) assembly to give the drive belt the tension specified. Refer to belt tension check in Section 03-05 . Tighten the drive belt tensioner and adjustment bolts to 47-64 Nm (35-47 lb-ft).
  1. Install the power steering pump support, if removed.
  1. Install the oil dipstick tube.
  1. Install the pressure hose tube nut and new Teflon® wagner into power steering pump valve outlet fitting (3D654) and tighten to 41-54 Nm (30-40 lb-ft).
  1. Connect the power steering return hose to the power steering pump, and reposition the clamp.
  1. Fill the power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent fluid meeting specification ESW-M2C33-F. Start the engine and turn the steering wheel (3600) from left to right without hitting stops to remove air from the system.
  1. Check for leaks and recheck the fluid level. Add fluid if necessary to proper level as specified in Section 11-00 .


    Power Steering Pump and Power Steering Pulley, 2.3L TPH Engine, Ranger Only





    Item Part Number Description 1 2882 A/C Compressor Mounting Bracket 2 N606543-S2 Bolt (2 Req'd) 3 N606069-S2 Bolt (2 Req'd) 4 N605803-S2 Bolt 5 N800199-S8M Screw 6 3D673 Power Steering Pump Pulley 7 3F671 Power Steering Belt Idler Support 8 N806020-S2 Bolt 9 3A674 Power Steering Pump 10 19703 A/C Compressor A — Tighten to 21.2-29 Nm (16-21 Lb-Ft) B — Tighten to 40.3-55 Nm (30-41 Lb-Ft) C — Tighten to 44-51 Nm
    (32-38 Lb-Ft)

    Power Steering Pump and Power Steering Pulley, 3.0L Engine, Aerostar





    Item Part Number Description 1 3A674 Power Steering Pump 2 3C511 Power Steering Pump Support 3 6007 Engine 4 N803564 Stud 5 N802827-S2 Nut 6 N800199-S8M Screw (3 Req'd) 7 N8011179-S2 Screw (3 Req'd) 8

Jun 09, 2010 | 1996 Ford Explorer

1 Answer

How to remove and install a fan belt for Audi 1988 model 80?


loosen all the bolts on the alternator,swing it inward,toward the block,then fit belt,swing outward,with a lever to tighten belt,before tightening all bolts.(easy,but spanner rash......)

May 21, 2010 | 1988 Audi 80

2 Answers

Looking to see haw difficult it is to change power steering pump.? any ideas Iam some what mechanicaly inclined


GM Astro/Safari 1985-1996 Repair Guide
Power Steering Pump - REMOVAL & INSTALLATION
(see Figures 1, 2, 3, 4, 5, 6 and 7)

199f8a3.jpg

Fig. 1: Exploded view of the power steering pump assembly mounting-2.5L engine

1544b7a.jpg

Fig. 2: Exploded view of the power steering pump assembly mounting-early-model 4.3L engine

8c93529.jpg

Fig. 3: Removing the power steering pump pulley-1985-92 vehicles

1995aea.jpg

Fig. 4: Installing the power steering pump pulley

d000dbb.jpg

Fig. 5: Pump pulley removal and installation-1993-96 vehicles

e8e94e6.jpg

Fig. 6: Exploded view of the power steering pump mounting-late-model 4.3L engines (1993-96 shown)

44caf14.jpg

Fig. 7: Typical power steering pump hose routing-1996 shown


The following procedure requires the use of the GM Puller tool No. J-29785-A (1985-92), Puller J-25034-B (1993-96) or equivalent, and the GM Pulley Installer tool No. J-25033-B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993-96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
WARNING Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  1. Remove the power steering pump from the vehicle.
To install:
  1. Position the pump to the vehicle, then uncap and connect the pump hoses.
  2. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm).
On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  1. Install the pump pulley using the GM Pulley Installer tool No. J-25033-B or equivalent. Press the drive pulley onto the power steering pump.
  2. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  3. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment.
  4. For 1993-96 vehicles install the upper fan shroud and the hood latch assembly.
  5. For 1996 vehicles, install the air cleaner assembly.
  6. Connect the negative battery cable.
  7. Refill the power steering reservoir and bleed the power steering system.
  8. Remove the jackstands and carefully lower the vehicle.
  9. Road test the vehicle, then check and top-off the power steering fluid.

hope this help (remember rated this post) Good luck.

May 13, 2010 | 1989 GMC Safari

1 Answer

Replace power steering pump


NOTE: The following procedure requires the use of the GM Puller tool No. J–29785–A (1985–92), Puller J–25034–B (1993–96) or equivalent, and the GM Pulley Installer tool No. J–25033–B or equivalent.
  1. Disconnect the negative battery cable for safety.
  2. For 1996 vehicles, remove the air cleaner assembly for access.
  3. For 1993–96 vehicles, remove the hood latch and the upper fan shroud.
  4. Release tension and remove the drive belt. For details, please refer to Section 1 of this manual.
  5. Remove the power steering pump pulley using a suitable puller tool.
  6. Remove the power steering pump retaining bolts, then reposition the pump as necessary for access to the hoses.
  7. Position a fluid catch pan under the power steering pump.
  8. Remove the hoses from the power steering pump and drain the excess fluid into the catch pan.
  9. WARNING
    Be sure to cap all openings in the pump hydraulic system to prevent excessive fluid spillage and the possibility of system contamination.
  10. Remove the power steering pump from the vehicle. To install:
  11. Position the pump to the vehicle, then uncap and connect the pump hoses.
  12. Install the steering pump to the retaining bracket, then secure using the retaining bolts. Tighten the power steering pump-to-bracket bolts to 37 ft. lbs. (50 Nm). For 1996 vehicles, tighten the nut to 30 ft. lbs. (41 Nm). NOTE: On early-model vehicles where the drive belt is tensioned by pivoting the power steering pump assembly, do NOT fully tighten the mounting bolts at this time, since you will just have to loosen them again for belt installation and adjustment.
  13. Install the pump pulley using the GM Pulley Installer tool No. J–25033–B or equivalent. Press the drive pulley onto the power steering pump.
  14. Hand-tighten the pivot bolt, the adjusting bolt and the washer.
  15. Install the drive belt. On early-model vehicles so equipped, properly adjust the belt tension. For details on belt installation and tension adjustment, please refer to Section 1 of this manual.
  16. For 1993–96 vehicles install the upper fan shroud and the hood latch assembly.
  17. For 1996 vehicles, install the air cleaner assembly.
  18. Connect the negative battery cable.
  19. Refill the power steering reservoir and bleed the power steering system.
  20. Remove the jackstands and carefully lower the vehicle.
  21. Road test the vehicle, then check and top-off the power steering fluid.
Fig. 3: Removing the power steering pump pulley — 1985–92 vehicles

213c6a5.jpg
Email me at greg.bernett@mcchord.af.mil for an engine picture breakdown.

    Jul 22, 2009 | 1990 GMC Safari

    1 Answer

    Do you have the steps to replace the pump


    Notes Power steering pump, replacing

    Note: As the illustrations in this service information are used for different model years and/or models, some variation may occur. However, the essential information in the illustrations is always correct.

    Preparation

    Warning: Used fluid is considerably more dangerous than new fluid. Avoid skin contact with the oil.

    Remove

    • the oil hose from the mounting on top of the power steering pump
    • the auxiliaries belt.
    Note: If there is dirt in the fluid, drain the system and remove the hoses from the steering gear.

    Removing the power steering pump/engine strut
    Applies only to diesel cars:

    Remove

    113652509


    • the screw at the pump
    • the screw at the engine.
    Leave the strut hanging in the delivery line.

    Removing the feeder hose and delivery line
    Install

    113652510


    • the lock grip pliers on the feeder hose as close to the power steering pump as possible
    • the lock grip pliers on the return hose at the fluid reservoir.
    Note: Place paper over the generator (GEN) as protection against oil.

    Remove

    • the screw nipple. Remove the delivery line from the pump
    • the hose clamp. Remove the feeder hose from the power steering pump.
    Warning: Avoid skin contact with the oil.

    Removing the power steering pump
    Remove

    113652511


    • the 3 screws
    • the servo pump.
    Installing the power steering pump
    Install

    • the servo pump
    • the three screws. Tighten to 25 Nm .
    Installing the power steering pump
    Install

    • the feeder hose. Tighten the clamp
    • the delivery line. Do not tighten yet.
    Installing the power steering pump/engine strut
    Applies only to diesel cars:

    Install

    • the strut
    • the screw at the engine. Tighten to 24 Nm
    • the screw at the pump. Tighten to 24 Nm .
    Finishing
    Tighten the delivery line. Tighten to 25 Nm .
    Remove paper and lock grip pliers.
    Install the auxiliaries belt.

    113652512



    Jun 06, 2009 | 2004 Volvo XC90

    Not finding what you are looking for?
    2000 Audi A6 Logo

    Related Topics:

    121 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Audi Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    yadayada
    yadayada

    Level 3 Expert

    61168 Answers

    Thomas Perkins
    Thomas Perkins

    Level 3 Expert

    13152 Answers

    Are you an Audi Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...