Question about 1995 Subaru Legacy

1 Answer

Subaru thankyou for your quick reply i made an error in my opening statement i meant crankshaft not cam shaft the pulley has completley come off the crank hub i cant see how they were joined as the pulley has no scoring and there seems to be a 1/16"gap between the pulley and the hub

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 98 Answers

Well this sounds like the rubber is broke that connects pulley to hub... This is called a vibration dampner the crankshaft pulley has to be replaced it is attatched by bolt and can only be installed one way ... Hope this solves your problem.....Good Luck

Posted on Jan 02, 2009

  • David Quesenberry
    David Quesenberry Feb 09, 2009

    the whole crank shaft pulley needs replacement

  • David Quesenberry
    David Quesenberry Feb 09, 2009

    crank shaft needs to be replaced

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How many foot pounds of torque should i tighten the bolt that holds on the harmonic balance on a 1996 subaru legacy outback


From FSM:

B: INSTALLATION
1) Install the crankshaft pulley.
2) Install the pulley bolt.
To lock the crankshaft, use ST.
ST 499977400 CRANKSHAFT PULLEY
WRENCH
(1) Clean the crankshaft pulley thread using an
air gun.
(2) Apply engine oil to the crankshaft pulley bolt
seat and thread.
(3) Tighten the bolts temporarily with tightening
torque of 44 N·m (4.5 kgf-m, 33 ft-lb).
(4) Tighten the crankshaft pulley bolts.
Tightening torque:
127 N·m (13 kgf-m, 94.0 ft-lb)

Apr 10, 2014 | 1998 Subaru Legacy

1 Answer

Position of cam shaft censor in the ford f150


nstructions
    • 1

      Insert the square tip of a 1/2-inch socket wrench into the square hole in the center of the serpentine belt's adjustment pulley. The adjustment pulley is the smallest pulley the belt wraps around.

    • 2

      Pull the adjustment pulley toward the engine with the socket wrench to release the tension on the serpentine belt, then pull the belt off the air conditioningicon1.png compressor's pulley.

    • 3

      Remove the bolts which secure the air conditioning compressor to its mounting brackets with an open-end wrench, then position the compressor to the side of the engine compartment. Do not disturb the hoses that attach to the compressor.

    • 4

      Pull the electrical connection off the crankshaft sensor.

    • 5

      Remove the two bolts that secure the crankshaft sensor against the engine with an open-end wrench, then slide the sensor out of the engine.

    • 6

      Slide the new crankshaft sensor into the engine, then install and tighten the sensor's two securing bolts with an open-end wrench.

    • 7

      Press the electrical connection onto the crankshaft sensor.

    • 8

      Position the air conditioning compressor against its mounting brackets, then install and tighten the compressor's bolts with an open-end wrench.

    • 9

      Pull the serpentine belt's adjustment pulley toward the engine with the socket wrench, then position the belt onto the air compressor's pulley.



Read more: How to Replace the Crankshaft Sensor in a Ford F-150 ' eHow.com http://www.ehow.com/how_6769823_replace-crankshaft-sensor-ford-f_150.html#ixzz2Ebai9Ftj

Dec 09, 2012 | 1998 Ford F150 Regular Cab

2 Answers

Where is the cam shaft location sensor located on a 2005 gmc yukon


camshaft sensor located above crankshaft pulley, the camshaft sensor mounted on the front timing cover above the crankshaft pulley.

Sep 17, 2012 | 2005 GMC Yukon

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

My balance shaft belt broke while I was driving. It stripped some of the teeth off the timing belt and Im pretty sure it jumped time. I need a diagram to show the timing marks and how to get it back in...


see diagrams from autozone.com. Cam sprocket has an "UP" label, but also 2 scribes on the sides to align to upper head surface. The critical part of the job is keeping tension on the side of the belt that is opposite from the tensioner as the tensioner is released onto the belt. The timing marks must be aligned when the job is done.

2bd7a51.jpg
4256a1c.gif To install:

  1. Install the camshaft timing sprocket so that the UP mark is up and the TDC marks are parallel to the cylinder head gasket surface. Install the key and tighten the bolt to 27 ft. lbs. (37 Nm).
  2. Install the crankshaft sprocket so that the TDC mark aligns with the pointer on the oil pump. Install the spacers with their concave surfaces facing in. Install the key. If equipped, install the TDC sensor assembly back into position before installing the timing belt.
  3. Install and tension the timing belt. Use a 6 x 1.0 mm x 25 mm bolt threaded through the cam belt tensioner plate to temporarily hold the tensioner.
  4. Temporarily install the crankshaft pulley and rotate the crankshaft counterclockwise 5-6 turns to be sure the belt is properly seated.
  5. Set the No. 1 piston at TDC for its compression stroke.



WARNING If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves.

  1. Rotate the crankshaft counterclockwise so that the camshaft pulley moves only 3 teeth beyond its TDC mark.
  2. Loosen, then retighten the temporary cam belt tensioner bolt.
  3. If the rear balance shaft sprocket/gear case assembly was removed, perform the following:
    1. If the rear balance shaft was moved, rotate the balance shaft until the 6 x 1.0mm x 100 mm bolt can be installed into the maintenance hole to the scribed line.
    2. Align the notch of the balance shaft sprocket edge with the pointer on the gear case. Install the rear balance shaft sprocket/gear case assembly using a new O-ring coated with fresh engine oil. The balance shaft sprocket should be installed in the TDC position. The pointer on the gear should align with the pointer on the oil pump housing plate.
    3. Tighten the mounting bolts to 18 ft. lbs. (25 Nm).

  4. If the front balance shaft sprocket was removed, perform the following:
    1. Install a suitable and sturdy screw driver or drift through the maintenance hole in the shaft behind the sprocket to hold the front balance shaft.
    2. Install the front balance shaft sprocket and mounting nut. Torque the nut to 22 ft. lbs. (29 Nm).

  5. Make sure the balance shafts and crankshaft are in the TDC position.
  6. Remove the crankshaft pulley, and if removed, install the balance shaft belt drive sprocket.
  7. Install the balance shaft belt, making sure the balance shafts and sprockets are still in the TDC position.
  8. If removed, install the balance shaft belt tensioner and tension the balance shaft belt.
  9. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  10. Remove the 6 x 1.0mm x 100mm rear balance shaft holding bolt.
  11. Temporarily install the crankshaft pulley and rotate the crankshaft 2 revolutions counterclockwise, stopping at TDC.



WARNING If any resistance is felt, stop immediately and determine the cause.

  1. Recheck that all of the TDC marks align for both the camshaft and balance shafts.
  2. Loosen, then retighten the tensioner adjusting nut to 33 ft. lbs. (45 Nm).
  3. Remove the 6 x 1.0 mm x 25 mm bolt used to secure the camshaft timing belt tensioner.
  4. Remove the crankshaft pulley and install the lower cover.
  5. Install the crankshaft pulley, lubricate the bolt threads and both sides of the crankshaft pulley bolt with fresh engine oil and tighten the crankshaft pulley bolt to 181 ft. lbs. (245 Nm). Do Not use an impact wrench.
See Figures 19 and 20


087aa27.gif

              Fig. Fig. 19: Holding the rear timing balancer shaft-4-cylinder Odyssey



            811a2fe.gif

            Fig. Fig. 20: Aligning the front timing balancer shaft-4-cylinder Odyssey

            1. Install the upper timing cover and the valve cover. Be sure the seals are properly seated.
            2. Install the side engine mount. Tighten the through-bolt to 47 ft. lbs. (64 Nm). Tighten the mount nut and bolt to 40 ft. lbs. (55 Nm) each.
            3. Remove the floor jack.
            4. Install and tension the alternator belt.
            5. Install the power steering pump and tension its belt.
            6. Install the splash shields.
            7. Reconnect the positive and negative battery cables. Enter the radio security code.
            8. Check engine operation.

            Sep 20, 2010 | Honda Odyssey Cars & Trucks

            2 Answers

            Where does the cam-crank sensor go on a 1993 pontiac bonneville?


            I don't know about the cam sensor, but the crankshaft position sensor is located just behind the crankshaft pulley, or possibly even right on the pulley. Should be just a small little thing with a couple small bolts holding it down. If you are changing it out, just be very careful to get it reinstalled in exactly the right position, they can be very finnicky.

            Aug 20, 2010 | 1993 Pontiac Bonneville

            1 Answer

            Were is the cam shaft senor and the crank shaft senor located


            this car does not have a camshaft sensor the distributor pick up coil acts as a cam sensor here is crank sensor info the crank sensor is located in front of engine just behind the crankshaft pulley using ohmmeter check resistance between terminals on sensor replace is not within specs cold 1630-2740 ohms hot 2065-3225 ohms if this is not the problem please reply to your post ill monitor it. hope this helps

            Jul 26, 2010 | 1996 Toyota Corolla

            1 Answer

            Setting the timing in a 1993 subaru justy


            If you are talking of the rubber timing belt setting then rotate the cam gear till the timing mark (small hole) on the camshaft gear aligns with the mark on the plastic cover behind it. Mark is on top of plastic cover (12 'o' clock).
            Rotate the crank till the timing mark (groove, not the one for the crankshaft woodruff key) on crankshaft gear is aligned with the mark on the bottom of the plastic cover behind it. (6 'o' clock).
            Tighten tensioner against timing belt rotate engine a few times make sure alignment of timing marks remain.

            Dec 14, 2008 | 1992 Subaru Justy

            1 Answer

            Instaling a timing belt on 2002 daewoo lanos


            I have a 2001 Lanos and I've replaced my belt twice (after breaking the first one at speed and having to replace the engine). The two cam gears have timing marks that should point towards each other. If you hold a ruler up with the edge of it passing through the center of the cam shaft bolts, the timing marks on each cam should be lined up on with the edge of the ruler and pointing towards each other. The crankshaft gear (not the big pulley) has a small triangle timing mark on it that should point almost straight down. There is a V cut into the oil pan that actually should line up with the cranshaft timing mark. BE VERY CAREFUL because if you rotate the crankshaft independently of the cams, you can tear up the valves very quickly.

            Dec 05, 2008 | 2002 Daewoo Lanos

            1 Answer

            Car Flooding-Not starting


            I had the same symptoms. I had to count the correct number of teeth from the crankshaft pulley to the cam pulley marks.It is a different number of teeth to each pulley.It turns out that I was off by one or two teeth on one cam.

            Jul 22, 2008 | 1992 Subaru Legacy

            Not finding what you are looking for?
            1995 Subaru Legacy Logo

            Related Topics:

            133 people viewed this question

            Ask a Question

            Usually answered in minutes!

            Top Subaru Experts

            yadayada
            yadayada

            Level 3 Expert

            61037 Answers

            Colin Stickland
            Colin Stickland

            Level 3 Expert

            21949 Answers

            Jeff Turcotte
            Jeff Turcotte

            Level 3 Expert

            6812 Answers

            Are you a Subaru Expert? Answer questions, earn points and help others

            Answer questions

            Manuals & User Guides

            Loading...