Question about 1994 Chevrolet K1500

2 Answers

Replacing a 4L60E with a 700R4?

I have a 94 Chevrolet 1500 (4X4 with a 5.7 liter) pickup with the 4L60E tranny. Can I remove the 4L60E and replace it with a 700R4 (and obviously not utilize the computer). If so, will this ''mess'' with the ecm?

Posted by on

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

I have a 99 suburban and it is slipping trying to go into 3rd and won't maually shift into 1st and 2nd

Posted on Aug 12, 2011

  • mike 20074 Mar 17, 2015

    This will need a full rebuild

×

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 180 Answers

Not with good results, the 4L60E is run by your ecm, the 700R4 while looking close to the same does not relie on your ecm for commands,it relies on a cable to regulate your line pressure.

Posted on Jan 01, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't it shift into 3rd or 4th?


It doesn't sound right, the majority of the Chevrolets from the smaller jimmy to the full size pickups had 4L60E transmissions in them. Reverse works fine as well? Could possibly be a shift solenoid.

Dec 04, 2015 | 1995 Chevrolet Tahoe

1 Answer

Wiring 99 4l60e 4x4 tranny from suburban to 98 pickup problem


Hi Jesse, You need to get the correct management system and probably the wiring harness to go with it. It will also require someone conversant with electronics and who knows the circuit of the vehicles concerned. Regards John

Nov 28, 2013 | Chevrolet Cars & Trucks

1 Answer

Will 400 transmission fit my 1994 c1500 pickup with overdrive


no. in the late 80's chevy switched to a electronic automatic tranny called the 4L60E, that is the tranny you should be looking for. the only bad part, its more expensive.

Aug 21, 2010 | 1994 Chevrolet C1500

1 Answer

4.3 liter, Rocker nuts back off at idle


I would try using some Loctite Threadlocker, they offer different strengths, removable and non-removable.

May 15, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

93 chevy 4x4 with a 4l60e tranny. will a 98 tranny swap?


Nothing after 1995, because from 1996 on the transmissions are for OBD II. Your truck has OBD I.

May 05, 2010 | Chevrolet Silverado 1500 Cars & Trucks

1 Answer

Swapped tranny, just need help with matching up wiring


It won't work. The shifting of the 4L60E is done by the computer in the 93. You might check with Summit or Jegs, I think they make a system to make it work.

Feb 20, 2010 | 1990 Chevrolet Suburban

1 Answer

I just installed a used 4l60e in my '97 Tahoe. On test drive, it shifts from 1 to 2, then about 1/2 way to 3, it downshifts back to 1. Any ideas about the problem?


how many miles on the tranny your put in? those don't last any more then about 120-140. the sunshell breaks, you should replace it with "the beast"

all shifting is in the valve body, you don't need to remove the tranny again. If your going to open her up and start wrenching, get a video/book on the 4L60E, you will start with check electrical components

Nov 16, 2009 | 1998 Chevrolet C1500

1 Answer

4L60E slipping and not locking up


Very well could be taht the Computer is not recieving the Shift codes Correctly. Just for an Easy Solution, Remove the ECM Fuse from the Fuse panel for 2 or 3 Minutes to Reset the Computer and let me know what you get.

Dec 31, 2008 | 1994 Chevrolet K1500

Not finding what you are looking for?
Cars & Trucks Logo

1,793 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

74688 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22082 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7288 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...