Question about 1995 Ford Econoline

1 Answer

DOES A 95 E-150 HAVE A REAR HEATER CORE? IF SO WHERE?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 4 Answers

The front heater core is right above where the passenger's feet are normally resting, where the glove box would be on a pickup. there is a modesty panel that you have to take off, then the plastic cover that houses the HVAC duct work, and the heater core,

Posted on Jan 04, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Have to what seems to be a radiator leek on passenger side right in front of rear tire. I looked underneath and saw rubber "coolant" lines right above the spring? My question is: is this part of...


Hi, this is the heater core for your rear heater. If it's leaking from inside the box, it's likely the core is bad. Please let me know if you would like instructions for replacing the rear heater core. A new core is $92 at autozone, but I would shop around. Make sure you specify the rear or auxiliary when ordering a new new core, as the front core is different.

May 28, 2011 | 2000 Dodge Caravan

1 Answer

Rear heater core lines leaking near firewall


If the tubes going to the rear heater core are the problem , drain the system and replace the bad tube/tubes. If the actual heater core is leaking and you do not want to go to the expense of replacing it, unhook both tubes at the back of the motor , cut out a good section of hose and use it to loop/connect the outlet line and inlet line on the motor side (not the rear heater core side). This will bypass the rear heater core , the front heater core should be adequate to heat the whole car. If you have a pin hole in a section of solid (copper) tubing, you can cut out the bad section and reconnect it with some heater tube and two hose clamps.

Dec 04, 2010 | 1999 Plymouth Grand Voyager

1 Answer

How to replace heate core 1988 buick reagal


REMOVE OR DISCONNECT
  1. Negative battery cable.
  2. Drain cooling system.
  3. Upper firewall weatherstrip.
  4. Upper secondary cowl.
  5. Heater hoses from core.
NOTE Blowing out residual coolant from inside the heater core will prevent coolant leakage into the passenger compartment when the heater core is removed.


  1. Sound insulator.
  2. Rear seat duct adapter.
  3. Heater duct.
  4. Heater core cover.
  5. Heater core.
INSTALL OR CONNECT

  1. Heater core.
  2. Heater core cover.
  3. Heater duct.
  4. Rear seat duct adapter.
  5. Sound Insulator.
  6. Heater hoses to core.
  7. Upper secondary cowl.
  8. Upper firewall weatherstrip.
  9. Fill cooling system and check for leaks.
  10. Negative battery cable.

ba5091b.gif

f8f6a8e.gif

Oct 21, 2010 | 1988 Buick Regal

1 Answer

How to replace a heater core


Heater Core Removal & Installation Front To Remove:
  1. Make sure you have the anti-theft codes for the audio and the navigation system, and then write down the audio presets.
  2. Disconnect the negative cable from the battery.
  3. From under the hood, disconnect the heater valve cable from the heater valve. Turn the heater valve arm to the fully opened position.
  4. When the engine is cool, drain the engine coolant from the radiator.
  5. Disconnect the inlet heater hose and the outlet heater hose from the heater core.
  6. Remove the mounting nut from the heater unit. Take care not to damage or bend the fuel lines, the brake lines, and related parts.
  7. Remove the dashboard.
  8. Remove the evaporator.
  9. Remove the mounting bolts and remove the heater unit. Front heater unit honda-10-00-4128.gif

  10. Remove the self-tapping screws and the clamp.
  11. Carefully pull out the heater core so you don't bend the inlet and outlet pipes.
Front heater core honda-10-00-4129.gif

To Install:
  1. Using care, install the heater core to the heater unit and secure.
  2. Using care, install the heater unit and tighten mounting nuts and bolts to 7 ft-lb (10 Nm).
  3. Install the evaporator.
  4. Install the dashboard.
  5. Connect the inlet heater hose and the outlet heater hose to the heater core.
  6. Connect the heater valve cable to the heater valve.
  7. Refill the cooling system with engine coolant.
  8. Adjust the heater valve cable.
  9. Make sure that there is no coolant leakage.
  10. Make sure that there is no air leakage.
  11. Connect the negative battery cable.
  12. Perform the power window control unit resetting procedure.
  13. Enter the anti-theft codes for the audio and the navigation system, and then enter the audio presets.
Rear To Remove:
NOTE: The rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system) and the rear power transistor (climate control system), the rear air mix control motor (climate control system) , the rear mode control motor and the rear expansion valve can be replaced without removing the rear heater-A/C unit.
  1. Remove the self-tapping screws and the clamp, and then remove the bolts and the rear evaporator lines with the rear expansion valve. If necessary, remove the rear expansion valve. Use a second wrench to hold the other fitting on the valve so the rear evaporator lines won't twist. Leave the first fitting loosely connected so you can use it to hold the valve while you loosen the second fitting.
  2. Remove the rear heater hoses.
  3. If necessary, remove the rear blower motor, the rear heater core, the blower screen, the rear blower resistor (heating/air conditioning system), the rear power transistor (climate control system), the rear air mix control motor and the rear mode control motor.
  4. Remove the self-tapping screws and the lower housing.
  5. Remove the self-tapping screws, and carefully separate the left upper housing from the right upper housing. Remove the rear heater core.
Rear evaporator assembly honda-10-00-4116.gif

To Install:
  1. Replace the rear heater core.
  2. Attach the heater hoses.
  3. Make sure no air is leaking from the left upper housing and the right upper housing fitting and from the upper housings and the lower housing fitting.
  4. Before reassembly, make sure that the rear air mix control linkage and door move smoothly without binding.
  5. Before reassembly, make sure that the rear mode control linkage and door move smoothly without binding.
  6. Reassemble the housing.
  7. After reassembly, make sure the rear air mix control motor runs smoothly.
  8. After reassembly, make sure the rear mode control motor runs smoothly.
  9. Refill the cooling system and make sure that there is no coolant leakage.
prev.gif next.gif

Oct 16, 2010 | 2005 Honda Pilot

1 Answer

My truck smells like anti-freeze and the left side of the windshield fogs up... the defrost only blows hot air on the passenger side. Ive been told by two shops that I have to replace the heater core... I...


You need to replace the front one, that one sit under the dash, your truck has front and rear a/c and heater, the rear heater core is for the rear unit, that heater core is to give you heat for the rear unit, that heater core sit in the rear of your truck inside on the side, that one don't have anything to do with the front one leaking, order the one for the front unit. hope this was very helpful.

Aug 18, 2010 | Chevrolet TrailBlazer Cars & Trucks

1 Answer

How to uninstall heater core from 2002 camaro


Drain the engine coolant. Refer to Draining and Filling Cooling System in Engine Cooling.
Remove the heater hoses..
Remove the heater core tube clamp bolt.
Remove the heater core tube clamp.
Remove the heater core shroud seal.
Remove the heater rear case bolts (Remove the heater rear case.
Slide the heater rear case downward in order to disengage the upper case clip.
Remove the heater rear case.
Remove the instrument panel (IP) compartment door. Refer to Door Replacement - Instrument Panel (I/P) Compartment .
Remove the heater core clamp bolt
Remove the heater core clamp.
Remove the heater core

Feb 25, 2010 | 2002 Chevrolet Camaro

1 Answer

REPLACING HEATER CORE


HEATER CORE REPLACEMENT REMOVAL PROCEDURE 1. Remove the fuel injector sight shield. 2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. 3. Use J 38185 in order to position aside the heater hose inlet and outlet clamps at the heater core. 4. Disconnect the inlet and outlet heater hose from the heater core. 5. Remove the RH Instrument Panel Closeout/Insulator panel. 6. Remove the LH Instrument Panel Closeout/Insulator panel 7. Remove the floor carpet. 8. Remove the rear floor air outlet duct from the holes in the floor reinforcement. 9. Disconnect the rear floor air outlet duct from the heater air outlet cover. 10. Remove the rear floor air outlet duct. 11. Remove the heater air outlet cover screws . 12. Remove the heater air outlet cover heat stakes with a small chisel. 13. Remove the heater air outlet cover from the HVAC module assembly. 14. Remove the heater core cover screws . 15. Remove the heater core cover heat stakes with a small chisel. 16. Remove the heater core cover from the HVAC module assembly. 17. Remove the heater core from the HVAC module assembly. 18. Remove the heater core foam seal (1) from the HVAC module assembly.
INSTALLATION PROCEDURE 1. Install a new heater core foam seal to the HVAC module assembly. 2. Install the heater core to the HVAC module assembly. 3. From the inside of the heater core cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 4. Install the heater core cover to the HVAC module assembly. NOTE: Refer to Fastener Notice in Service Precautions. 5. Install the heater core cover screws . Tighten Tighten all screws to 1.5 N.m (13 lb in) . 6. From the inside of the heater air outlet cover, drill the dimples adjacent to the heat stakes using a 5.5 mm (7/32 in) drill bit. 7. Install the heater air outlet cover. 8. Install the heater air outlet cover screws (2). Tighten Tighten the screws to 1.5 N.m (13 lb in) . 9. Connect the rear floor air outlet duct to the heater air outlet cover. 10. Install the rear floor air outlet duct to the holes in the floor reinforcement. 11. Install the floor carpet. 12. Install the RH Instrument Panel Closeout/Insulator panel. 13. Install the LH Instrument Panel Closeout/Insulator panel. 14. Connect the inlet and outlet heater hose to the heater core. 15. Use J 38185 in order to reposition the heater hose inlet and outlet clamps to the heater core. 16. Install the fuel injector sight shield. 17. Fill the cooling system.

Nov 13, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

Replacing heater core on 2004 monte carlo


REMOVAL PROCEDURE 1. Remove the fuel injector sight shield. 2. Drain the cooling system. Refer to Draining and Filling Cooling System in Cooling System. 3. Use J 38185 in order to position aside the heater hose inlet and outlet clamps at the heater core. 4. Disconnect the inlet and outlet heater hose from the heater core. 5. Remove the RH Instrument Panel Closeout/Insulator panel. 6. Remove the LH Instrument Panel Closeout/Insulator panel 7. Remove the floor carpet. 8. Remove the rear floor air outlet duct from the holes in the floor reinforcement. 9. Disconnect the rear floor air outlet duct from the heater air outlet cover. 10. Remove the rear floor air outlet duct. 11. Remove the heater air outlet cover screws (2). 12. Remove the heater air outlet cover heat stakes (1) with a small chisel. 13. Remove the heater air outlet cover from the HVAC module assembly. 14. Remove the heater core cover screws (2). 15. Remove the heater core cover heat stakes (1) with a small chisel. 16. Remove the heater core cover from the HVAC module assembly. 17. Remove the heater core from the HVAC module assembly. 18. Remove the heater core foam seal (1) from the HVAC module assembly

Nov 08, 2009 | 2004 Chevrolet Monte Carlo

Not finding what you are looking for?
1995 Ford Econoline Logo

Related Topics:

123 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...