Question about 2006 Honda Pilot

Open Question

2nd row passenger side seat is jammed and won't slide forward

The seat pivot release latch works fine, but the seat will not slide forward to allow a passenger easy access to step into the third row seats. I don't know how to take out the seat or can't seem to locate the source of the jam.

Posted by on

  • ronmoor44 Feb 08, 2009

    I am having the same problem.



    Ron

×

6 Suggested Answers

  • 1 Answer

SOURCE: the third row seat is stuck in the collapsed

I had to take it to the dealer to get it 'unstuck' and they ended up bending the frame of the backseat! If you can get into the spot where it locks into the trunk frame you can unlock it yourself, but you need a second person to hold the seat back form the trunk frame so you can POSSIBLY squeeze your hand or a tool in there to do it. Its VERY DIFFICULT! Hope that made sense...lol

Posted on Apr 06, 2009

FIXYA Benny
  • 165 Answers

SOURCE: Power seat won't recline

are there any other leavers or dials around the seat that you can see that may operate the back rest independantly?
can you see the motors are they intact?
is there a button that selecets the particular funtion you wish to do?
it is functional, can you test that?
dirt is a major key in faulty switcches and can oftem be cleaned

Posted on May 05, 2009

Contronics
  • 20 Answers

SOURCE: middle row back seats...how can

first fold them flat then pull the handle which will release the rear bottom brackets and allow you to pull back and lift the entire seat out of the van....both seats.

Posted on Jun 03, 2009

  • 41 Answers

SOURCE: Remove seat from second row in Honda Mini Van 2007

on the passenger side feel under the seat and there is a lever that pulls toward you as you stand at the sliding door.

First, raise the armrest, then lower the back all the way forward. Then remove the headrest sit it out of the way and while pulling the lever under the seat towards you, lift up the seat from the back so it tilts forward. When it is standing on its "nose" lift first one side shifting it either forward or backwards to clear the rod on which it is hooked. Do the same with the other side of the seat and then lift it out. Installation is the reverse of removal.

The other seat is much the same, though sometimes the lever is a little different but in the same place.

Good luck,
bob

Posted on Jun 09, 2009

  • 1 Answer

SOURCE: Seat adjustment forward and back stuck

I had this problem not to long ago, it's a very easy fix! I agree with that garr651!

There is a a thin metal wire that runs from the left & right side under the seat. Each end of the wire loops around a small hole on each track bracket and is held in place by two small washers that fit inside a grove.

Check to see if the washers are in the groves and holing each end of the wire tightly. If they're not simply slide them back into place and make sure the wire tight.

The easiest way to do this is to look under the driver seat from the back seat. Also a pair of needle nose pliers may become handy (although not necessary).

Posted on Jun 17, 2009

Preeth Tom
  • 129 Answers

SOURCE: remove third row in 2006 odyssey

hi
its difficult to remove third row seat but either by pumping hot air to it or by sucking out the water by water ****** sponge. if its necessary to remove then better to take the car to an autorised service station

Posted on Jul 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i remove the 2nd row out of my town & country


There are two handles to be used on the side of the seat. One allows seat to fold forward and the other allows it to lift forward. There is a bar under the front of the seat which releases the cams which hold the seat mounts. Hope this helps.

Jul 03, 2014 | 2003 Chrysler Town & Country

1 Answer

Holden astra 2000 model


If the latch releases on both sides, then it may be jammed sideways just enough to hold it from sliding. Check if the seat sits evenly on the runners-move the left side back and forth to get the right side sliding. You may have to get a screwdriver or prying tool under the latch on the right runner, to make sure it releases fully. If it is a wire from the lever to the right latching tab on the runner, they get easily stretched.

Dec 07, 2013 | Cars & Trucks

1 Answer

Jus t purchased a used 2003 yukon xl and trying to find out how to fold the 2nd row seat down cannot find a lever on the one side


The passenger side 2nd row release lever is at the lower right corner. On the driver side, there is no release lever, just a pull ******** the center of the seat, that sometimes falls between the seat.

Aug 26, 2011 | 2003 GMC Yukon XL

1 Answer

I have a old mercury villager ...i want to replace the middle row seat with last row seat ...is it posible...?


The middle row seat slides forward to the middle position (and several other positions as well.)

Owners manual explains how to slide rear seat foreard.
Remove middle row seats. Lift handle under 3rd row seat cushion on passenger side. Raise seat cushion up until it locks up. Then lift the lever on the passenger side of seat and pull seat forward until it locks in place.

if you don't have owner manual, go to motorcraft.com, pro center, tech info, owner manual.
join our group for free help.

please rate too. Thanks.

http://groups.yahoo.com/group/villagerquest/

Jan 24, 2011 | Mercury Villager Cars & Trucks

2 Answers

My trunk is stuck shut, how can i get it open? they key will not turn and the latch thing by the front near the gas release will not work either...


If you have rear seats that fold down you can access the latch mechanism from the left side rear seat....if you are flexible. pull the corner of the seat forward to allow your arm to slide in behind. about 14-16" in, feeling up inside the trunk you can feel 3 quarter size holes in the sheet metal. The second hole has the cable release arm. stick your finger up there are pull towards you. this will release the seat allowing it to fold down. Crawl into the trunk. there is a glow in the dark release handle on the inside of the trunk lid to open the trunk.

Jun 29, 2010 | 2005 Toyota Corolla

1 Answer

Turn the seat around on a VW van?


There is a small round metal wire that comes out of the front center of the seat. If you sit on the seat, while depressing the wire down, and pivot using your body weight, the seat should turn. Sometimes spraying the black seat mount is necessary to lube it. You may have to remove the seat if rusty or very dirty. To do that, slide the seat as far forward as possible, then lift the small metal lever on the left side of the seat, to release the lock on the track allowing the seat to move forward off the track. Note: both the passenger and drivers seats should turn on your model.

Jun 23, 2010 | 1986 Volkswagen Wagon Camper

1 Answer

2003 chevy tahoe 2nd row seating


lower the bottom portion, there will be two black cables. follow them toward the back of the seat, past a black round plate, where they become top and bottom cables. Push down toward the floor board on the bottom cable (my bottom cable is no longer black coated but rather a bare feeling cable wire). When pushing down on the bottom cable, pull the seat forward. As the seat does come forward the headrest will fold back at the same time. Not an easy find for me either, they should just make a release lever, but oh well..... I Hope this helps. Just keep playing around with those two cables until it finally does release.

Feb 20, 2009 | 2003 Chevrolet Tahoe

9 Answers

Kia Sedona seat stuck


Got it, with the help and eyes of my wife. The rear latch releases as the seat back is lowered. This release is ALMOST seat back down (about 3 inches above the seat bottom). As the seat back lowers, apply constant lift on the rear latch, and it will release as the seat back lowers. Hard-won knowledge - I think I invented some bad words in the process.

Jan 03, 2009 | 2006 Kia Sedona

1 Answer

2003 YUKONXL 2ND SEAT DOES NOT SLIDE ON TRACK,


It sounds like one or more of the release cables came undone from your lever. Lift the lever, inspect all around it, look under the seat where the track is. There should be a small round cable that runs from your handle down to the release. Also there may be a thin wire that runs from the left side to the right side. If you find it and reconnect it you should be golden.
Good Luck!

Dec 14, 2008 | 2003 GMC Yukon XL

Not finding what you are looking for?
2006 Honda Pilot Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...