ECU pinout? I'm seeking pinout info on an ECU I've pulled from my recently dysfunctional 93' 1.3L Swift (auto trans unfortunately). The ECU is a Denso unit, L4, 1.3-AT-CAM, 33920-63E4 O, 112000-2170. My crappy service manual schematic connector pin numbering does not seem to match what I can read on the ECU PCB. Problem was / is ign abrupt failure. Traced & cleared all except primary coil drain switch at / in ECU but cannot trace actual wire through the firewall.....help?

[PDF]WIRING DIAGRAM BY MODEL - Apexi

www.apexi-usa.com/manuals/electronics/neo_diagram.pdf

TOYOTA. Table of Applicable Models. ..... The orientation of the ECU depends on the vehicle with ECU pins. Install the ECU fully checking the .... 2MZ?FE. '97.5?'02.1. VEROSSA. JZX110. 1JZ?GTE. '01.8?'04.4. L. T10?b. HW?23.

1997 Camry V6 ECU Pinout - Toyota Nation Forum : Toyota Car and ...

www.toyotanation.com/.../97568-1997-camry-v6-ecu-pinout.html

Sep 19, 2005 - 10 posts - ‎3 authors
So as the title says, Anyone know the pinout to help with a SAFC install? ... look in the apexi install manual, it is t8-f. the same as the 2mz-fe ... Perkins 99 Camry 1mz Build
15 posts
Nov 28, 2012
1mz-fe to 2mz-fe
15 posts
Feb 25, 2010
SAFC Wiring Pin-Out for 94 1MZ-FE - Toyota Nation ...
8 posts
Feb 8, 2008
1996 1mz ecu pinout needed and question
10 posts
Feb 18, 2006
More results from www.toyotanation.com

Have you recently had the brakes worked on .it could be the emergency brake hanging up .

the tranny is dying i think. you might've lost all your gears but 1st and 2nd thats why it's not shifting. if you have a semi-manual mode try all the gears and if they dont change then it definitely is the tranny

3s, humm...... what is that, google shows ZERO for that.
can i know what object shows that? dash, ECU, trans shift.? what?
where are your eyes looking,?
is this the ECU flash code>? LED? at ECU?

"1985-91 Prelude models, there is only one LED display."
ECU code 3 is bad MAP (or bad vacuum to it)

Carb engine or EFI engine./ and which engine?> "options"

here is the FSM , look it up , gen 2 to 5
http://hondatech.info/downloads/Auto/Manuals/Prelude/

which computer. what year.
in the old swift the ECU/PCM is reset 3 ways.
1: pulling the ECU memory fuse.
2: pulling battery neg lug for 5min or step on brakes and put back lug.
3: scan tool , reset, You wont have this,its old 0bd1 tool.

come cars have a A/T computer, called a TCM.

p5m? (what is that.)
no matter,
all the schematics are at alldata.com , pay the 15 clams and look.

this is an obd2 trouble code table, it can help you underdtand your code.

and i should charge you for this info, but ill be nice. aquire the appropriate pinout diagram for your ecu's plugs. then proceed to verify each of the ecu's power wires have the correct voltage. then proceed to perform a continuity test on all ecu grounds. this means checking voltage from the ecu plug to the ground location that the wire goes to. you should find your problem somewhere within there if you have already swapped out with a KNOWN GOOD ecu.

if this is a manual transmission it should take 80-90 weight gear oil,the same as in the differential.if its an automatic trans then us the manufactures required oil as with auto trans oil they have different additives that if the wrong one is put in it can cause problems.

If you are having problems with reading the engine computer and the engine is malfunctioning, you may have a bad ECU "engine computer".

Have you tried the local dealer for the info? You might be able to try alldata. com. Toyota also has a pay web site for factory info. This is the same site that the factory uses.