Question about 1993 Nissan Quest

2 Answers

Need torque specs for oil pan gasket

Replacing the oil pan gasket on a 1993 Nissan Quest. I would like to know the torque specs on the pan and is there an ordered pattern to follow when tightening the pan bolts?

Posted by on

  • 6 more comments 
  • dmalinows493 Jan 01, 2009

    I know this will sound funny,



    But thank you Thundergod!! Hahaha



    Appreciate the information. Proceeded as instructed and no leaks as you predicted.



    Thanks again,



    Happy Nissan Driver again.......

  • Anonymous Mar 16, 2014

    tporque specs oil pan bolts on a 1997 dakota 3.9 v6

  • Anonymous Mar 16, 2014

    replacing head gasket need bolt torque specs and sequence

  • Anonymous Mar 22, 2014

    replacing oil pan and using gasket instead of silicone sealer,is there any spec for tightening pan bolts

  • Anonymous Mar 22, 2014

    I replaced the clutch and noticed the pivot ball was bad, when I went to put the new one in the ball started turning and got loose, the spec`s call for 25 pounds torque, what did I do wrong?

  • Anonymous Mar 28, 2014

    How to remove oil pan from night a 1993 Ford Topaz Need help

  • Anonymous Mar 28, 2014

    Need help replacing oil pan on a 1993 Ford Topez

  • Anonymous Mar 29, 2014

    Need torque and tappet settins

×

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Nissan Master
  • 6,982 Answers

There likely is a spec for oil pan but unless you are a finatic, you really don't need to know what it is. Simple rule: Don't crank down ******* any fastener. If corners near crank ends have larger fasteners, you can tighten them a bit more than on siderails. Before tightening anything, install all bolts finger tight, to ensure that they are not cross threaded. To avoid warping pan, tighten from the center of the pan, working towards both ends, alternating from side to side as you go. When you are finished, go over it again, using the same amount of force on each bolt. As I said, end bolts can if larger in diameter, be tightened more but be careful not to tighten so much that you will either split or push the gasket out the sides.. Anywhere two gasket ends **** together, I recommend using a sensor -safe dab of silicone. An oil pan is not under any mechanical stress or pressure. I have used this method for many years and NEVER had one leak. If you really need #s, small fasteners get about 12-15in lbs, larger ones about 20.

Posted on Dec 31, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Just wondering if it's necessary to have any <a rel='nofollow' href="http://www.permadrywaterproofing.com/">permadry</a> experience when taking out insulatory materials in your basement.. Any suggestions or advice is welcome. Thanks!

Posted on Jun 06, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

98 jeep wrangler tj 4.0 oil pan bolt pattern or layout. An torch specs


Bobby, oil pan bolt torques for 4.0 Wrangler. Oil Pan Bolts 1/4 84 in-lbs Oil Pan Bolts 5/16 132 in-lbs As far as sequence, see last link, start in center, criss cross pattern tighten snug all, then repeat to torque spec.
Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Oil Pan Gasket leaking
http://jeephorizons.com/tech/99_40l_torque_specs.html
98 jeep 4 0 oil pan bolt torque sequence specs Google Search

May 21, 2016 | Jeep Cars & Trucks

1 Answer

Leaking transmission fluid


TRANSMISSION FLUID LEAKS,CAN BE FOUND AROUND PAN GASKET.CHECK PAN GASKET,IF IT LOOKS WET AND YOU SEE FLUID DRIPPING AROUND THE EDGE OF OIL PAN, REPLACE PAN GASKET, WHILE YOU REPLACING PAN GASKET REPLACE TRANSMISSION FILTER WHILE OIL PAN OFF.IF TRANSMISSION OIL PAN NOT LEAKING, CHECK TRANSMISSION OIL COOLER LINES GOING INTO RADIATOR YOU WILL LOOSE A LOT OF FLUID THERE ALSO TORQUE SHAFT SEAL WILL CAUSE HEAVY FLUID LEAK WHILE ENGINE RUNNING CHECK OIL COOLER LINES AND LOOK AT THE TORQUE AREA WHILE ENGINE RUNNING YOU WILL SEE FLUID POURING WHILE ENGINE RUNNING THE OIL PUMP PRESSURE WILL PUSH FLUID OUT AT THE LEAKING AREAS.

Aug 01, 2011 | 1991 Nissan Stanza

1 Answer

I NEED TO KNOW THE TORQUE SPECS FOR THE OIL PAN ON A 1994 BUICK LESABRE 3.8 L. V6


Exploded view of the oil pan and related components - 1993 vehicle shown

48ac114.jpg


* If removed, install the oil pump pipe and screen. Secure with the retaining bolt(s) and tighten to 89 inch lbs. (10 Nm).

* Place a new formed rubber gasket in the oil pan flange.


* Position the oil pan and secure with the oil pan-to-engine bolts. Tighten the bolts to 124 inch lbs. (14 Nm). Do NOT overtighten the bolts, as this will damage the oil pan, causing a leak.


Hope help with this (remembere rated and comment this help).

Mar 08, 2010 | 1994 Buick LeSabre

1 Answer

I am replacing an oil pan gasket on my 1995 toyota tercel i need to know the torque specs


Testing by FixYa Staff

Please do not rate this post!

We apologize for any inconvenience.

Jul 14, 2009 | 1993 Nissan Quest

2 Answers

Have 1990 corvette with slight oil leak on oil pan. Was told I needed to tighten bolts to correct torque. Need to know torque and in what sequence


Unless you are replacing the gasket, I'd just go around the pan and snug them up. I doubt you'll be able to hit all them very easily with the motor in the car.

Just use common sense and make them snug and don't overdo it and you should be fine. It will be clear which ones are loose when you put a wrench on them.

Good luck.

Jul 07, 2009 | 1990 Chevrolet Corvette

1 Answer

What are the oil pan torque specs for a 1997 Mazda 626 2.0L


try these websites www.autozone.com and the other one is www.alldatadiy.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your van.

Jun 30, 2009 | 1993 Nissan Quest

1 Answer

Need torque specs for oil pan bolts


torque specs for these bolts can be found in a Haynes or Chilton manual availiable from your local parts store, or maybe at your local library, however these bolts are usually no more than 14 ft pounds, unlike cylinder head bolts, the bolts do not need to have any stretch factor to hold the oil pan gasket in place or sealed.

May 17, 2009 | 1997 Ford Ranger SuperCab

1 Answer

1999 Saab 9-5 oil pan torque spec


they should be torqued with a 3/8 torque ratchet to 30 inch pounds.

Mar 06, 2009 | 1999 Saab 9-5

1 Answer

I am seeing small puddles of oil under our 96 nissan quest?


you can take it to any auto repair place.Like sears pep boys or a local repair shop. some times you can get away with a few turns on the bolts holding the pan up

Jan 19, 2009 | 1993 Nissan Quest

Not finding what you are looking for?
1993 Nissan Quest Logo

3,028 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

70347 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...