Question about 1996 Ford Taurus

1 Answer

I need to do serpatine belt on 96 ford taruaus 3.0

I need to replace serpatine belt on 96 ford taruaus 3.0. need to know process

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,990 Answers

On the Inside of the Engine Compartment you will find the Routing Sticker for the Belt to Reinstall. Locate the Tensioner (Will look like a Pulley that has one Round Pulley Under the Belt and One larger Round Pulley Mounted Above that. In the Middle of the Large Pulley there is a Bolt. Get a Wratchet and Turn it. It will Lower the Pulley under the Belt and Loosen the Tension Off of the Belt. Remove the Belt. Follow the Diagram Under Hood to Reinstall.

Posted on Dec 31, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 ford fusion keeps throwing serpatine belt


The most common reasons for this are the belt is stretched and not tight on the pulleys, or one of the pulleys is not aligned with the others.

Feb 25, 2013 | 2006 Ford Fusion

2 Answers

ROUTING FOR SERPATINE BELT 3.0 V/6 2001 SE


hear is the diagram please leave positive feedback.

sgm1115_21.pngsgm1115_22.png

Apr 16, 2011 | 2001 Ford Taurus

1 Answer

I need a diagram for the serpatine belt


You should have one....either on the underside of your hood or on the top of the radiator. If it is too dirty to see well, try gently wiping it off with some isopropyl (rubbing) alcohol and a cotton cloth.

Apr 15, 2011 | 1997 Ford Ranger SuperCab

1 Answer

I started my 2001 camero and smoke filled the inside through the vents this happened after a hard feeze, there was antifreez in the car, smoke also came out from under the hood. I turned the car off and my...


It sounds more likely to be the water pump that has failed.You should have it repaired as soon as possible or your timing belt may snap and cause further damage.
I hope I have been of help

Feb 14, 2011 | Chevrolet Camaro Cars & Trucks

1 Answer

The serpatine belt on my 96ford taurus broke. I fixed it but it still does not start.I recharged the battery still nothing.It tries to turn over


i think that when the belt broke it has damaged the wires too the crank sensor which could be on the front pulley

Jul 29, 2010 | 1996 Ford Taurus

1 Answer

My rotors are shot.How do i replace them? Also had a bad antifreeze leak. Pulled over and found hole in hose. Addressed problem so i thought.Now when i shut it off it leaks pretty good. Did the cheap...


Without being hurtful. Reading your story,I would suggest taking your vehicle to a repair shop and leaving all your issues in the hands of the folks that take care of those issues every day.

May 06, 2010 | 1995 Ford Econoline

1 Answer

1999 serpatine belt


Hi,the serpentine belt is tensioned automatically by means of a spring loaded tensioner,this is released by using a long 1/2 inch extension bar which fits into a square hole, once pulled back the tensioner can then be held by a nail etc, which is inserted into a hole which aligns with another hole,thus holding the tensioner back in a pre-loaded position to allow you to replace the belt,once replaced you can then pull back the extension bar to remove the nail again and then slowly let off the tension, IF replacing the tensioner, The new one comes pre-loaded with a pin in location to hold it ,hope this is of some help, Bill.

Feb 20, 2009 | 1999 Saab 9-5

1 Answer

Size of serpatine belt to reroute with out AC


hi the only way to get the size is to use a piece of string and wrap it around all of the pullies.in the proper order. and subtract 1-2 inches so thy tenshioner will work buy a couple of belts at diffrent sizes and return the ones you dont need

Feb 02, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
1996 Ford Taurus Logo

Related Topics:

213 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

63291 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...