Question about 2006 Chevrolet Trailblazer Ext

4 Answers

2006 Trailblazer Headlight Replacement

How do I replace the passenger side, low beam bulb om my 2006 Trailblazer?

Posted by on

  • 3 more comments 
  • EriK22 Jan 03, 2009

    Thanks, so much. I had a little trouble with the "rod" under the fender, but I finally got it. All is well, again thank you...

  • EriK22 Jan 14, 2009

    Again thanks for the advice. I agree "clips" may have been a better term, but I figured it out. I was able to the passenger side (the bad one) without having to remove anything else. Again, thanks for taking the time to advise.

  • Anonymous May 13, 2009

    2005 TRAILBLAZER HOW TO REPLACE LOW BEAM LIGHT ON DRIVERS SIDE?

  • Anonymous Mar 22, 2014

    no power on contour test

  • Anonymous Mar 27, 2014

    replaced headlight switch no luck

×

4 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

There are not two rods, there are two clips one under fender weild and one right above the light on top of the cover. Pull up on these two clips and pull the light forward a couple of inches and remove the dust cover. You have to take the air filter cover off to be able to reach in and replace the light. It took me about 10 min to figure these out but hope it helps out.

Posted on Jan 14, 2009

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 2 Answers

There are two slides accessed at the top of the headlamp assembly - they slide up, this allows the headlamp to move forward about two inches only to pop the rubber dust cover off. the bulb can be removed and the new one put in put the new bulb in the socket partially before connecting the wire, twist into socket, replace cover, reinstall slides and done in two minutes

Posted on Jul 09, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 62 Answers

There should be two rods holding the headlight in place and you just lift them up and the headlight will come out. you take the old headlight out and replace it with the new one and put the headlight assembly back in. I hope that helps.

Posted on Dec 31, 2008

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

Take the air cleaner off for the pass side. take the battery out for the drivers side, after raising the two retaining clips. the operation is still a pain it the!! Leroy

Posted on Mar 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

4 Answers

I have a 2006 civic SI. DRL indicator is on, driver side low and high beam ok. Passenger side low beam ok but DRL and hi beam not working. Any help is appreciated.


When either the high or low beam light is out in either side, DRL (daytime running lights) indicator will come on. When one bulb goes out, that's a clue the opposite bulb will burn out soon, so its best to replace both bulbs. If it was a fuse issue, both left and right side would be out. If driver side is OK but passenger side is not, then its a bulb issue. A 2006 Honda civic takes 9006 (HB4) low beam bulbs and 9005 (HB3) high beam bulbs. Cheapest is online from Walmart site-2-store. After procuring, wear latex, vinyl, or ANY gloves to keep your (corrosive) oil skin from coming in contact with headlight glass bulbs. Your skin oil will chemically react and cause shorter life span on glass bulbs. Instruction don't tell you this, so you handle with your hands, then need to replace bulbs 3 years later instead of 5 years (or more) in the future. With gloves on, pop the hood and look behind each headlight. Turn counter clockwise to unlock headlight bulb holders. Its a quarter to half turn to unlock bulb holder lock. Replace one bulb at a time so you don't confuse high beam from low beam. The wire has a tab you need to lift to pull out & disconnect wire connector. You might need a slim narrow-**** (NOT phillips) screwdriver to lift the tab; or use your house key. Snap the wire connector to the new bulb, then twist into headlight housing to secure bulb holders, then move on to the next bulb to repeat the procedure. Pict below, 9005 high beam is on the left, 9006 low beam is on the right. Handle by grasping the plastic base, not the glass bulbs. The raised potrusion on the bottom center is where the tab locks onto wire connector. Replace all 4 bulbs now, but in the future, its likely the low beam will wear out before the high beam. In the future, replace only the pair, not all 4. The factory installs inferior bulbs that go out sooner, hoping you'll take to dealership and they ******** you with higher parts-n-labor fees. As opposed to Walmart online site-2-store, it would cost you AT LEAST triple in parts & labor from dealership to replace all 4 headlight bulbs :-(
45d1f6ac-2983-42b9-a46c-30ef441b89e7.jpg

Nov 29, 2013 | 2006 Honda Civic

1 Answer

How do you change the low beam light on 2006 chevy trailblazer?


For the drivers side, reach down by your alternator and over behind the headlight. You'll feel a 3" round rubber boot. Slip this off and now you can remove the light bulb.

Passengers- Remove the top of the air cleaner, at that point you'll have complete access to the rubber boot and bulb.

Mar 14, 2011 | 2006 Chevrolet Trailblazer

1 Answer

How do you replace a low beam headlight bulb in a 2006 Chevy Trailblazer?


Drivers side- reach hand behind headlight and remove the rubber cover, then turn and remove bulb.

Passenger side- remove air cleaner top and move the air cleaner out of the way. Now you have access to the rubber cover to replace the bulb

Dec 13, 2010 | 2006 Chevrolet Trailblazer Ext

1 Answer

Need to replace low beam headlamps on 2006 Chevy Trailblazer.


For the passenger side- need to remove the air cleaner top and move the air cleaner out of the way. You can now access the rubber covers that protect the bulbs.

For the Drivers side, just stick, your hand down behind the headlight and remove the rubber cover.

Remember, do not touch the new bulbs, the oil from our hands will burn a hold in the bulb.

Dec 11, 2010 | 2006 Chevrolet Trailblazer Ext

1 Answer

How do I replace the low beam bulb?


Both sides have a rubber cover behind the actually headlight. There are 2 rubber covers, one on the top for the high beams and one on the bottom for the low beams. Drivers side is easy, reach your hand down there and remove. The passenger side requires removal of the air cleaner top to have easy access. Hope this helps!

Dec 05, 2010 | 2006 Chevrolet Trailblazer

2 Answers

Bulb replacement for passenger side low beam on 2003 Mazda6


Google "mazda6club" - a very good forum and search "changing headlight bulb. Hope this helps.
Cheers,Peter

Mar 01, 2010 | 2003 Mazda Mazda6

1 Answer

2004 Chevrolet TrailBlazer. Passenger front low beam headlamp out


FACE THE VEHICLE SO THAT BATTERY IS ON YOUR RIGHT;
2.REMOVE THE BLACK PLASTIC PIECE THAT RUNS OVER RADIATOR BETWEEN HOOD LATCH AND FAN. IT IS ABOUT 53 1/2" LONG AND HOLDS THE HOOD PROP CLIP. (3 PLASTIC PUSH RETAINERS & 2 SHEET METAL SCREWS);
3.REMOVE THE GRILL ASSEMBLY UNDERNEATH THE PIECE IN STEP 2 BY PUSHING DOWN FIRMLY ON 4 RETAINER CLIPS WHICH RUN ALONG THE TOP. USE A WIDE SLOT SCREWDRIVER. PULL UP GENTLY ON GRILL ASSEMBLY. IT WILL POP OUT. THE GRILL ASSEMBLY EXTENDS UNDER EACH HEADLIGHT ASSEMBLY (HA) AND IT DISPLAYS THE CHEVROLET LOGO IN THE MIDDLE. MY GRILL ASSEMBLY POPPED OUT EASILY AND ALL THE OTHER RETAINER CLIPS ON THE BOTTOM AND BENEATH AND TO THE SIDE OF HA WERE AUTOMATICALLY RELEASED WITHOUT ANY FUSS;
4.ON TOP OF HA SEE ONE TAB (ABOUT 1" LONG)ON THE RIGHT SIDE AND ONE ON THE LEFT (THE ONE ON L IS CLOSER TO THE FENDER);
5.PULLUPWARDDIRECTION ON TABS. THEY WILL SLIDE UPWARD A COUPLE OF INCHES AND WILL RELEASE THE HA WHICH YOU CAN THEN PULL OUT TOWARDS YOU;
6.AT BACK OF THE HA, REMOVE 2 ROUND RUBBER CAPS (ABOUT 4" IN DIAMETER)--ONE FOR LOW BEAM--ONE FOR HIGH. REVEAL BULBS. UNSNAP THE WIRE HARNESS FROM BULB BASE AND TURN BULB 1/4 TURN CLOCKWISE (REMEMBER YOU ARE FACING THE TRUCK)
7.REPLACE BULB(S). #9006 BULB IS GRAY-BASE, FOR HIGH BEAM ON OUTSIDE. #9005 IS BLACK-BASE, LOW BEAM TO INSIDE OF HIGH BEAM.
CHANGING HIGH AND LOW AND REASSEMBLY TOOK ABOUT HALF HOUR. GOOD LUCK. ALTERNATIVE: IF YOU ARE REPLACING THE PASSENGERSIDE HEADLIGHT JUST REMOVE THE AIR FILTER COVER AND PULL PLUG OUR FROM BEHIND HEADLIGHT AND REPLACE. BE CAREFUL HANDLING LIGHT BULB. TO CHANGE THE ONE ON THE DRIVER'S SIDE JUST REACH IN FRONT OF THE BATTERY TO ACCESS THE PLUG AND HEADLILGHT. TOOK ABOUT 5 MINUTES. ENJOY YOU TRAILBLAZER, GREAT TRUCK.

Feb 20, 2010 | 2004 Chevrolet TrailBlazer

1 Answer

Passenger Low Beam Headlight needs replacement!!!


You could remove the air filter cover and then you will be able to reach the bulb.

Apr 12, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

2005 Honda CRV High Beam


Honda Headlight Bulb(H1) - This bulb is the high and low beam bulb for your vehicle. One bulb required for each headlight.

This headlight bulb fits:
  • CR-V 2005-2006 (requires 2 bulbs per side)

Mar 21, 2009 | 2005 Honda CR-V

Not finding what you are looking for?
Cars & Trucks Logo

8,689 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...