Question about 1994 Toyota Celica

1 Answer

Wishbone bush needs replacing on my 1994 celica 2.0gt auto

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 42 Answers

Not sure if bushing is replaceable but usually when the bushing is worn it is a sign that the front mount is worn, placing excessive load on the wishbone

Posted on Jan 01, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want to replace the offside front bush on the lower wishbone is it a difficult job and how long would you expect it to take


If you can get to a press it should not be a big deal,just remove the wishbone and press the old one out and the new ones in.

Jun 07, 2015 | 2009 Kia Carens 2.0

1 Answer

Grinding or creaking in 2008 ford fusion front end


Mr.Mangus have you checked at all your front suspension struts,shock absorbers,or lower wishbones with bushing and ball joints? I had recently a diesel ford focus 2007 with similar case and both front wishbones were replaced due to ball joints and bushes and then sent for steering alignment. Vehicle drive excellent. Please check.

Aug 16, 2012 | Ford Fusion Cars & Trucks

1 Answer

I have an oil leak from the front of my engine it a 96 2,0GT


IF THE OIL FILTER SCREWS ON TO IT IT IS A OIL COOLER CHECK THAT THE FILTER IS TIGHT

Aug 31, 2009 | 1993 Toyota Celica

2 Answers

Car sqeaking when going over bumps


It could be the wishbones, the springs or the inside panels rubbing which is also very common. Also, some shocks have plastic shields on them that tend to squeak

Jul 02, 2009 | 1996 Mercury Mystique

1 Answer

Wishbone front offside bmw mini one


you have to put the wishbone on 1st, the ball joint nut on and the front one den guide it in the hole and use a big lever with plenty of wd 40 and it will go in, i jus did one the other day, i had to change dat rear wishbone bush which was a nightmare to do

Mar 01, 2009 | 2004 Mini Cooper

2 Answers

Steering problem


it may be bad tires or you need an alignment done

Jan 25, 2009 | 1994 Ford Escort

1 Answer

Hilux surf lower wishbone bushes need replacing .is it a hard job


Hi,
If you are experiencing grinding noises when turning, it is usually the top strut bearings above the springs that transmits noise inside.
These get the worst of salt spray - so often turn to dust. You will need to drop the suspension to check this area out.
It could be that this ball joint is suspect too, but you can only tell with the pressure off it.
Also check other rubber bushes when the suspension is off, as wear on an inner one may not normally be noticed. Uneaven tyre wear is usually an alignment problem - so have the tracking checked by a garage with Laser equipment.

Jan 03, 2009 | 1993 Toyota Pickup

Not finding what you are looking for?
1994 Toyota Celica Logo

Related Topics:

335 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...