Question about 1994 Jeep Grand Cherokee

2 Answers

94 Jeep Grand Cherokee Transmission Problom

My trany went out of my 94 Jeep Grand Cherokee Larado and I was wondering if a 1997 Jeep Grand Cherokee trany will fit in my 94 they are both 6 cylinders and 4X4 and they are both 42re transmissions so I dont know because there mite be differint in ectronics is the trany

Posted by on

  • 1 more comment 
  • Docmosher Jan 04, 2009

    My 94 Jeep Grand Cherokee Laredo has problems starting. Once it starts,you can turn the ignition off and on repetedlely with no problem. However,when I try to shift into drive,it stalls after it warms up. It has 160K miles on it. I know it will run 200K plus,what can you tell me?

  • morrisonh364 Jan 07, 2009

    i put a 1997 transmission in my 1994 jeep grand cherokee laredo now it will not shift right i now the transmission is good

  • Anonymous Mar 30, 2014

    How to take a stock shifter off a 94 jeep grand cherroke

×

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 45 Answers

1994 is the same as 1997. parts are interchangeable

Posted on Dec 31, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Interchange Applications for 400-3128 Transmiss,Transaxle 1) Jeep Grand Cherokee 1993 A.T., 6-242 (4.0L, VIN "S"), 42RE (w/o drain plug in pan); 4x4 [3128] 2) Jeep Grand Cherokee 1994 A.T., 6 cyl, 4x4 [3128] 3) Jeep Grand Cherokee 1995 A.T., 6 cyl, 4x4, thru 1/13/95 [3128]
Interchange Notes for 400-3128
CH $2170
Ident: 52118028
Ident: 52118283
Ident: 52118317
Ident: 52118354
Ident: 52118729
CAUTION: Verify output shaft splines and torque conv. bolt pattern before interchanging.
4 spd A.T., 42RE.
Control module may require programming to allow proper shifting when interchanging.
Interchange information requested, need transfer case ident. # with corresponding desc. of tail shaft and conv. bolt pattern of transmission.

Posted on Oct 05, 2011

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

94 jeep grand cherokee larado


Hi Eric, it sound to me like the modulator in the trans is faulty. This modulator is what controls the shifting in the trans.It details a 30 minmute repair by your transmission specialist. The replacement part should be around a hundred dls, plus the labor. While you are at it, have the filter changed in the trans for carefree shifting.

Aug 27, 2014 | 1994 Jeep Grand Cherokee

1 Answer

How much transmission fluid goes in my 1997 Jeep Grand Cherokee Larado V6 and where do I fill it?


Hi there:
Check this information about your 1997 Jeep Grand Cherokee 4WD 4.0L MFI 6cyl...

- 42RE transmissionService change only - 4 quarts. Total refill - 11 quarts.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Jun 21, 2012 | 1997 Jeep Grand Cherokee

1 Answer

1997 jeep gr. cherokeeI have no reverse, and in neutral the vehicle moves forward what are the possible causes and solutions


time for a new transmission i have the same vehicle and it did the same thing until i changed trany out

Feb 12, 2011 | 1997 Jeep Grand Cherokee

2 Answers

What size bolt is it for the idler pulley for 1997 jeep grand cherokee larado?


Should only be one bolt going thru the center of the pulley. probably a 14 or 15mm size.


Dec 20, 2010 | 1997 Jeep Grand Cherokee

3 Answers

Jeep grand cherokee larado 1999 going above 50


sounds like it time to have the front end balljoints inspected. Only with an inspection will you get the proper results. Why guess, this is a safety issue.

Jul 23, 2010 | 1999 Jeep Grand Cherokee

1 Answer

What fluid goes in the transfer case of my 94 jeep grand cherokee larado?


on a select trac---mopar plus 4 atf or equivalent, quadra trac----mopar transfer case fluid or equivalent,

Jan 23, 2010 | 1994 Jeep Grand Cherokee

1 Answer

Where is the blower motor resistor located in the 1997 jeep grand cherokee larado?


IT IS UNDER THE GLOVE BOX NEXT TO THE BLOWER MOTOR.IT WILL HAVE 2 DIFFERENT ELECTRICAL CONNECTOR

May 07, 2009 | 1997 Jeep Grand Cherokee

2 Answers

1997 JEEP CHEREOKEE WONT GO INTO OVERDRIVE BUT THE OVERDRIVE LIGHT COMES ON LOOKING FOR A DIAGRAM FOR IT 4.0 LT MOTOR


Try to adjust the linkage cable on the transmission; if that don't work change the transmission fluid and filter.

Mar 02, 2009 | 1997 Jeep Grand Cherokee

1 Answer

94 Jeep Grand Cherokee MY transmission went out


no it wont work.they made too many changes with them about 2 years older and id say yes but no they wont interchange

Dec 31, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

1,441 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

63801 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...