Question about 1994 Oldsmobile Cutlass Ciera

1 Answer

Headlamp housing removal

I have a 1994 caravan how to remove headlamp housing and replace mounting and adjustment studs?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 840 Answers

Well you need to take off the bumper to get all of these its pretty easy top of bumper has retainer bottom of bumper has retainers and 2 bolts one on each side of the front fenders and pull of then you will see headlight bolts and how to change mount panel/ Please rate my response thank you very much

Posted on Feb 02, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rear turn signal b ulb burned out - How to replace


Rear Turn Signal, Brake and Parking Lights
  1. Remove the tail light assembly screws, then the assembly.
  2. Disconnect the twist lock socket from the lens housing. NOTE: To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1?4 turn, then remove the socket with the bulb; replace the bulb if defective. Fig. 7: Remove the tail light assembly screws, then the assembly - wagon shown 86816223.jpg Fig. 8: Twist the socket counterclockwise to remove from the housing 86816225.jpg Fig. 9: This type of bulb simply can be pulled out of the socket for replacement 86816226.jpg To install:
  3. Attach the socket assemblies to the back of the lamp unit.
  4. Install the lamp assembly to the vehicle with the mounting screws.
License Plate Light
  1. Remove the lens screws.
  2. Once the lens is removed you, can access the bulb and replace if needed. To install:
  3. Install the new bulb, then attach the lens to the body of the vehicle.
Center High Mount Stop Lamp
  1. Remove the screws securing the lamp cover.
  2. Remove the mounting nuts, then unplug the electrical harness to the lamp assembly.
  3. The lamp now should come out. To install:
  4. Position the lamp assembly to the vehicle, then attach the electrical harness to the lamp.
  5. Install the mounting nut, tighten to 62 inch lbs. (7 Nm).
  6. Attach the lamp cover. Fig. 10: Exploded view of the center high mount stop lamp assembly - wagon shown 86816230.gif
    Fig. 11: Light bulb application chart for all models with non-European headlamps 86816237.gif
    Fig. 12: Light bulb application chart for Buicks with European headlamps 86816235.gif
    Fig. 13: Light bulb application chart for Oldsmobiles with European headlamps 86816236.gif
    prev.gif next.gif

Dec 19, 2010 | 1994 Buick Century

1 Answer

Where do I find the cooling fan relay switch on a 2000 dodge grand caravan sport.


RADIATOR FAN RELAY
The radiator fan relay is located below the left front headlamp module Radiator Fan Relay The headlamp module must be removed to access the relay.

REMOVAL
Open hood, disconnect and isolate the battery negative cable.
Remove the left side headlamp bulb from the headlamp housing.
Remove the left headlamp module.
Remove the cover over the relay.
Disconnect the relay connector Radiator Fan Relay
Carefully drill out the two retaining rivets.
Remove relay from vehicle.

Jul 15, 2010 | 2000 Dodge Caravan

1 Answer

How to change headlight


This is the same for the pick up as is the Trooper:

Aerodynamic Type

e5d8044.gif
Replacing a headlamp bulb—1994 Trooper shown


8391601.gif
Replacing a headlamp bulb—1994 Trooper shown


  1. Disconnect the negative (−) battery cable.
  2. Open the hood and disconnect the headlight bulb electrical connector.
  3. There are two possible designs. For the first design, turn the bulb to remove it from the housing, for the second unscrew the retaining cap and remove the bulb.

    WARNING Do not touch the glass portion of the halogen bulb. Any contamination on the bulb may cause the bulb to burst when turned ON. If the bulb is contaminated, clean the glass portion with rubbing alcohol.

  4. Hold the bulb by the plastic portion only. Install the bulb and connect the wiring harness. Make sure the sealing ring is in place.


Non-Aerodynamic




3dbcbc6.gif Replacing a sealed beam headlamp—1990 Amigo shown

  1. Disconnect the negative (−) battery cable.
  2. Remove the front grille and/or headlight bezel.
  3. Remove the headlight bulb retaining rim, headlight and disconnect the wiring.
  4. Before installing, spray some silicone grease into the bulb socket.
  5. Connect the wiring and install the bulb.
  6. Install the retaining rim and grille.
  7. Adjustment: turn the adjusting screw (A) for vertical adjustment. Turn the screw (B) for horizontal adjustment.

Feb 14, 2010 | 1994 Isuzu Pickup

1 Answer

How to replace front turn signal housing


Front Turn Signal & Parking Lights
  1. On some models you will need to remove the headlight bezel mounting screws and the bezel.
  2. Remove the mounting screws for the lamp assembly.

af50756.gif
Remove the mounting screws securing the lamp assembly

  1. After the screws are removed, pull the assembly from the vehicle.

5deda5d.gif
After the screws are removed, pull the assembly from the vehicle

  1. Disconnect the twist lock socket from the lens housing.

90fe451.gif
Disconnect the twist lock socket from the lens housing

To remove the bulb, turn the twist lock socket (at the rear of the housing) counterclockwise 1/4 turn, then remove the socket with the bulb; replace the bulb if defective.


0568896.gif
Newer Oldsmobile models have the turn signal separate from the headlamp assembly ...


252443f.gif
... unlike the newer Buicks, where the unit is attached to the headlamp

To install:
  1. Install the electrical harness to the back of the unit.
  2. Position the signal assembly, then attach to the vehicle with the mounting screws. Tighten the screws to 54 inch lbs. (6 Nm).
  3. Insert the socket to the back of the unit, then attach the headlamp bezel if removed.

Feb 13, 2010 | 1992 Oldsmobile Cutlass Ciera

1 Answer

How do you remove the air filter box on a 2001


REMOVAL
Release hood latch and open hood.
Access Rubber Grommet
Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners.
Fastener Locations

Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield.
Remove Push In Fasteners
Remove the push pins attaching the fascia to the upper radiator closure panel.
Headlamp Jack screws

Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s).
Roll Fascia Forward

Roll fascia forward to clear way for headlamp housing removal.
Disconnect wire connector from back of lamp socket(s) and/or bulbs.
Remove Headlamp Housing

INSTALLATION
CAUTION : Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.

Place headlamp housing into position.
Connect wire connector to lamp socket(s)
Verify headlamp and signal lamp operation.
Install jackscrews to attach headlamp housing to crossmember.
Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
Install nut on fascia stud through the splash shield access hole.
Verify headlamp operation and alignment


Nov 03, 2009 | 2001 Chrysler 300M

3 Answers

87 Lincoln headlight changing instructions


You must first remove the Headlamp bezel which is the chrome trim that surrounds the duel headlamp housing. The chrome trim surround is mounted to the Headlamp mount panel with three nuts which you can only access on the inside. Pop open the hood and look on the inside near were the headlamp bulbs are. You will see the three mount nuts for the headlamp bezel. Might be rusty so first give it a shot of WD40 or similar. Remove the nuts and then you can lift the headlamp bezel from the outside away from the headlamp bulbs. The headlamp bezel only has tabs that slid into a slot on the bottom so you can lift out once the top three nuts are removed. Once the headlamp bezel has been removed you can then access the 4 screws that hold the headlamp trim ring2.gif in place which is what holds the headlamp bulb in place. There are several other screws that in the same area but they are only for adjustment of the headlamp bulbs within the housing. Leave them in place. Remove the stainless steel ring that is holding the lamp in place, and then unplug the headlamp from the back and replace the headlamp. Should take you less than 5 or 10 minutes. Dan

Sep 21, 2009 | 1989 Lincoln Town Car

2 Answers

How do i remove the brake drum on my 1996 dodge caravan


You remove the tire/wheel assembly and pull it off. Make sure you have removed the factory installed wheel lock tabs on your studs if they are still there.Discard them because they're not needed.

Jun 15, 2009 | 1994 Suzuki Swift

1 Answer

How do i change both headlights on my 2002 chevy cavillier


Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Hood close out filler panel.
    • Bolts from the headlamp.
    • Headlamp from the headlamp mounting panel.
    • Electrical connector from the headlamp.
    • Headlamp bulb/socket retainer ring from the headlamp.
c218bc4.gif

  • Headlamp bulb/socket from the headlamp.
  • Bolts from the headlamp adjuster mechanism.
  • Headlamp adjuster mechanism.
  • To Install:
    1. Install or connect the following:
      • Headlamp bulb/socket to the headlamp.
      • Headlamp bulb/socket retainer ring to the headlamp.
      • Headlamp adjuster mechanism to the headlamp housing, if necessary
      • Bolts to the headlamp adjuster mechanism. Tighten to 6 N.m (53 lb in).
      • Electrical connector to the headlamp.
      • Headlamp to the headlamp mounting panel and lower mounting bracket.
      • Bolts to the headlamp. Tighten to 10 N.m (89 lb in ).
      • Hood close out filler panel.

    Jun 06, 2009 | 2002 Chevrolet Cavalier Coupe

    1 Answer

    How do you replace headlamp bulbs on 1999 chrysler 300


    You half to remove the Headlamp housing to change it. Here is the instructions out of the factory manual.
    Tell me if this works for you?
    HEADLAMP HOUSING - CONCORDE/LHS/330M Headlamp lens fogging is a normal condition and does not require service unless excessive or continual. Moisture will vent from tubes or vents located on the back of the lamp.
    REMOVAL
    1. Release hood latch and open hood.
    2. Remove large rubber grommet (70 mm x 168 mm) from splash shield to gain access to fascia fasteners Access Rubber Grommet
    3. Remove fasteners attaching fascia to the front fender and splash shield, using access hole in splash shield Fastener Locations
    4. Remove the push pins attaching the fascia to the upper radiator closure panel Remove Push In Fasteners
    5. Remove jackscrews attaching headlamp housing to crossmember and remove the lamp housing to access the lamp(s) Headlamp Jackscrews
    6. Roll fascia forward to clear way for headlamp housing removal Roll Fascia Forward
    7. Disconnect wire connector from back of lamp socket(s) and/or bulbs.
    8. Remove headlamp housing Remove Headlamp Housing
    INSTALLATION CAUTION: Do not touch the glass of halogen bulbs with fingers or other possibly oily surface, reduced bulb life will result.
    1. Place headlamp housing into position.
    2. Connect wire connector to lamp socket(s) and/or bulbs.
    3. Verify headlamp and signal lamp operation.
    4. Install jackscrews to attach headlamp housing to crossmember.
    5. Align fascia to bumper reinforcement and install the top center push pins, to upper radiator closure panel.
    6. Align the two fascia studs to the fender vertical attachments, at the same time align the fascia groove on the horizontal flange with the fender drive pin. Push fascia rearward to engage the fasteners.
    7. Install nut on fascia stud through the splash shield access hole.
    8. Verify headlamp operation and alignment

    Mar 27, 2009 | 1999 Chrysler 300M

    1 Answer

    Instructions on replacing headlight assembly


    96 f150 procedure

    Headlamp Assembly Removal
    1. Remove radiator air deflector from radiator support.
    1. Remove two screws and two nuts retaining headlamp door (13064).
    1. Pull headlamp door from vehicle. Remove three bulbs and sockets.
    1. Disconnect engine control sensor wiring (12A581) from headlamp bulb (13007).
    1. Remove two retainers attaching upper two attachments of headlamp (13008).
    1. Turn horizontal headlamp adjusting screw (13032) completely out of the adjusting nut.
    1. Pull headlamp from vehicle.

    Oct 17, 2008 | 1994 Ford F150 Styleside Supercab

    Not finding what you are looking for?
    1994 Oldsmobile Cutlass Ciera Logo

    105 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Oldsmobile Experts

    yadayada
    yadayada

    Level 3 Expert

    61037 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    21949 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    6812 Answers

    Are you an Oldsmobile Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...