Question about 1989 Mazda MPV

1 Answer

How do i get the trouble codes off a 1989 mazda mpv?

The check engine light comes on on my 1989 mazda mpv,how do i retrieve the codes?

Posted by on

  • 4 more comments 
  • Anonymous Mar 14, 2014

    cluster light comes on and and turns off after 2 or 3 minutes and dont come one

  • Anonymous Mar 16, 2014

    overhead lights on 04 mazda mpv wont turn on unless the doors are opened what is wrong

  • Anonymous Mar 17, 2014

    sluggish going up hills feels like out of gas

  • Anonymous Mar 23, 2014

    over drive light tend to come on oinbce nin while

  • Anonymous Mar 27, 2014

    p1624 code

  • Anonymous Mar 28, 2014

    rear vent window glass coming loose

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 104 Answers

Http://img178.imageshack.us/img178/3331/obdikx3.jpg

The above link is to a diagram of your ALDL connector, all you need is a paper clip, straighten out the paper clip and insert one end into the diagnostic test pin and one in the system ground pin (terminals A & B).

Then put the key in the ignition and turn it to the on position but DO NOT start the engine. You will then see the check engine light flash. It will initially start by flashing once, then a pause and then flash twice and it will repeat this three times. That flash sequence indicates 12, which just means the system is operating. Its the flash sequences after that that will give you the code if any are stored.

For instance if it flashes twice, then pauses, then flashes four times, thats code 24. So any flash sequence you get after the initial 12 (flash once, pause, flash twice) you need write those down. Below is a list of diagnostic codes to tell you what the codes mean.

Code 12
1 flash, pause, 2 flashes
Diagnostic: This Code will flash whenever the diagnostic terminal is grounded with the ignition switch turned on and the engine is not running.

Code 13
1 flash, pause 3 flashes
Oxygen sensor voltage stays between 0.35 and 0.55 volts for 30 seconds when the TPS signal was above 0.55 volts. The engine had been running for at least 40 seconds with an engine temperature above 110° F.

Code 14
1 flash, pause, 4 flashes
Coolant temperature sensor signal indicates a temperature of over 284° F for 4 seconds after the engine had been running for at least 10 secondsCoolant Sensor Circuit (high temperature) If the engine is experiencing overheating problems, have those fixed before continuing. Check all wiring and connectors associated with the coolant temperature sensor. Replace the Coolant temperature sensor.

Code 15
1 flash, pause, 5 flashes
Coolant Sensor Circuit (low temperature) Coolant temperature sensor signal indicates a temperature colder than -36° F for at least 4 seconds after the engine had been running for 2 seconds. See above, then check wiring connections at the ECM

Code 16
1 flash, pause, 6 flashes
Charging system voltage was either below 9 volts or above 17 volts for 10 seconds. System High Voltage If the voltage is above 17.1 volts for more than 2 seconds, the Service Engine Soon light will illuminate. Have the charging system checked.

Code 17
1 flash, pause, 7 flashes
PCM did not detect any spark reference pulses within 240 fuel control reference pulses (80 crank revolutions) while engine was running below 1200 RPM. Spark Reference Circuit.

Code 21
2 flashes, pause, 1 flash
Throttle Position Sensor, TPS voltage was above 0.8 volts for 5 seconds when engine was running and air flow was less than 15 gm/sec, or the TPS voltage was over 4.8 volts at any time.

Code 22
2 flashes, pause, 2 flashes
Throttle Position Sensor check TPS adjustment. Replace the TPS sensor. TPS voltage was under 0.2 volts for 4 seconds when the ignition was on. Check for a sticking, or mis-adjusted throttle position sensor.

Code 23
2 flashes, pause, 3 flashes
Inlet air temperature sensor signal showed an air temperature of -29° F for 4 seconds. Manifold Air Temperature. Check the MAT sensor, wiring, and connectors for a possible open circuit. replace the MAT sensor.

Code 24
2 flashes, pause, 4 flashes
Vehicle speed sensor signal showed less than 3 MPH for 2 seconds when engine speed was greater than 3000 RPM and transmission has not been in park or neutral for more than 4 seconds. Or vehicle speed goes from above 18 MPH to 0 in less than 2 seconds without applying brake. This code can only appear when the vehicle is in motion, if it appears when the car is not in motion, ignore it. Check ECM connections, any other problems should be diagnosed by a qualified mechanic.

Code 25
2 flashes, pause, 5 flashes
Inlet air temperature sensor signal showed an air temperature of over 218° F for 5 seconds when vehicle speed was greater than 35 MPH. Check the voltage between the MAT sensor and the ECM. voltage should be above 4 volts.

Code 26
2 flashes, pause, 6 flashes
Quad-Driver sense voltage shows a low voltage when battery voltage should be present, or if the sense voltage shows battery voltage when a low voltage should be present for at least 5 seconds when the engine was running. Have the car checked by a dealer.

Code 27
2 flashes, pause, 7 flashes
2nd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 2nd or 4th gear switch was open when engine was first started. Gear switch Diagnosis Have the car checked by a dealer.

Code 28
2 flashes, pause, 8 flashes
3rd gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 3rd or 4th gear switch was open when engine was first started.

Code 29
2 flashes, pause, 9 flashes
4th gear switch was closed or grounded for 10 seconds when vehicle was in 4th gear, or 4th gear switch was open when engine was first started.

Code 31
3 flashes, pause, 1 flash
PRNDL indicates a gear other than park or neutral for 13 seconds for 3 consecutive startups when ignition was on, engine was off and vehicle speed was 0. Or the PRNDL status indicators (A, B, C, P) showed an incorrect combination of Lo and Hi for more than 10 seconds.
Check all connectors, and for a faulty switch.

Code 32
3 flashes, pause 2 flashes
EGR System Check vacuum hoses and connections for leaks and restrictions. Replace the EGR solenoid or valve.

Code 33
3 flashes, pause, 3 flashes
MAF Sensor Have the mass air flow sensor replaced.

Code 34
3 flashes, pause, 4 flashes
There was no MAF signal for over 4 seconds while engine was running. Check for loose or damaged air duct, misadjusted minimum idle speed and cacuum leaks. Inspect the MAF sensor and the electrical connections.

Code 38
3 flashes, pause, 8 flashes
The Torque Converter Clutch portion of the brake switch was open and caused the TCC to be inoperative, adjust OR replace switch.

Code 39
3 flashes, pause, 9 flashes
Torque Converter Clutch Check ECM connections, check for faulty Torque Conver Clutch solenoid.

Code 41
3 flashes, pause, 1 flash
Cam sensor signal was not received by PCM for the last 5 seconds while engine was running. Check for faulty connections, or a faulty cam sensor. Maybe also indicate a problem with the vehicle's timing chain.

Code 42
4 flashes, pause, 2 flashes
The Electronic Spark Timing (EST) signal did not change when the ECM applied bypass voltage to the ignition module. Check for faulty connections, or a faulty ignition module.

Code 43
4 flashes, pause, 3 flashes
Knock sensor signal was either above 3.5 volts or below 1.5 volts for at least 20 seconds. Check for a faulty knock sensor, or Mem-Cal.

Code 44
4 flashes, pause, 4 flashes
Oxygen sensor voltage was under 0.25 volts for up to 4 1/2 minutes of closed loop operation, lean exhaust. Check the ECM wiring connections. Check for vacuum leaks at the hoses and intake manifold gasket.

Code 45
4 flashes, pause, 5 flashes
Oxygen sensor voltage was over 0.75 volts for 2 minutes in closed loop operation with a throttle angle between 0.6 and 1.9 volts. Rich exhaust. Check the evaporative charcoal canister and its components for the presence of fuel.

Code 46
4 flashes, pause, 6 flashes
Power Steering pressure switch Check for faulty connections, or a faulty switch.

Code 48
4 flashes, pause 8 flashes
Misfire Diagnosis. Check the ignition and fuel systems.

Code 51
5 flashes, pause, 1 flash
Prom or Mem-Cal Make sure the MEM-Cal or prom is properly installed in the ECM. Replace Mem-Cal or prom.

Code 52
5 flashes, pause, 2 flashes
Cal-Pak Check the Cal-Pak to insure properation. replace the Cal-Pak.


Code 54
5 flashes, pause, 4 flashes
EGR #2 solenoid was out of range for 6 of 8 tests. 55 EGR #3 solenoid was out of range for 3 of 5 tests.

Code 55
5 flashes, pause, 5 flashes
ECM Check for faulty connections. Replace the ECM.

Code 56
5 flashes, pause, 6 flashes
Quad-driver voltage was incorrect for 5 seconds on the circuit connected to QDM "B".

Code 57
5 flashes, pause, 7 flashes
Boost control solenoid did not open bypass valve causing engine torque to be too high.

Code 63
6 flashes, pause, 3 flashes
EGR flow was incorrect. EGR solenoid did not work properly. Have vehicle serviced by a dealer.

Code 64
6 flashes, pause, 4 flashes
Same as Code 63 EGR flow was incorrect. EGR solenoid did not work properly.

Code 65
6 flashes, pause, 5 flashes
Same as Code 63.

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 mazda mpv missing when engine warms up


Sounds like possibly a coil starting to break down and fail. If the check engine light is on it would be fairly easy to retrieve trouble codes which could help identify the cylinder or cylinders that are. It working.

Apr 18, 2014 | 2006 Mazda MPV

1 Answer

Trouble code p0106


Code 106 is for a problem with the signal coming from the MAP sensor, not the EGR valve. The MAP sensor and circuits would need to be checked.

Jun 17, 2013 | 2002 Mazda MPV

2 Answers

Check engine light is on, engine missing


First get the trouble code that has been stored in the computer.Let me know what it is.

Jan 27, 2012 | 2003 Mazda MPV

1 Answer

MPV 2005 WARNING LIGHT COMES ON. PICTURE OF A ENGINE.WHAT DO I CHECK?


the light is what is called a check engine light it is part of the on-board computer system, the light came on because the on-board computer system has seen a fault with one of the sensor on the car, it could be about any of the 70 plus sensors, you will need to have the codes retrieved you can have this done at most any auto parts store after you get the codes get back with me and i will look it up for you.

May 06, 2011 | 2005 Mazda MPV

2 Answers

The light of check engine turn on in my mazda 3 the trouble is troubleshooting P2404


I check for engine codes at:
http://www.obd-codes.com/trouble_codes/
I couldn't find that code in the standard code list or the Mazda unique code list.

Apr 04, 2011 | 2006 Mazda MPV

1 Answer

How do you get the check engine light to go off on the 2000 mazda mpv


YOU HAVE TO SEE WHAT TROUBLE CODE YOUR PCM IS TRYING TO GIVE YOU.GO TO ANY AUTO ZONE THEY WILL DO IT FREE.CHECK ENGINE LIGHT IS NOT GOING TO TURN OFF UNTIL YOU FIX THE PROBLEM.

Mar 31, 2010 | 2000 Mazda MPV

1 Answer

Engine light is on and the engine is sputtering, feels like its going to stall


the engine light comes on when the computer system detects a problem. you need to retrieve the code with a code reader and then follow a flow chart for that code to find the necessary repair.Depending on you skill level, this job is better left to a pro

Mar 15, 2010 | 2002 Mazda MPV

1 Answer

My mazda mpv 2002 run rought and sometimes the check engine light flash


run scanner for trouble codes, some auto parts stores will do this for free

Sep 27, 2009 | 2002 Mazda MPV

1 Answer

Which is the #1 plug for firing order located to do a timing setting


You don't have your engine size posted so pick the applicable application:

1989 Mazda MPV
2.6 liter SOHC L4
cf032e2.gif
1989 Mazda MPV 2WD
3.0 liter DOHC V-6
cb46576.gif

Jul 15, 2009 | 1989 Mazda MPV

1 Answer

Engine light blinking in my Mazda MPV


A BLINKING ENGINE LIGHT INDICATES AN ENGINE CYLINDER IS MIS-FIRING. HAVE THE TROUBLE CODES TESTED TO DETERMINE WHICH ONE. DO NOT DRIVE THIS WAY AT HIGH SPEEDS AS IT MAY OVERHEAT THE EXHAUST SYSTEM AND CREATE A FIRE HAZARD.

May 01, 2009 | 2001 Mazda MPV

Not finding what you are looking for?
Cars & Trucks Logo

2,939 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...