Question about 2001 Lincoln Navigator

1 Answer

Exery time if put a new audio fuse in it immediately blows

No raido sucks!

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert who has written 50 answers of more than 400 characters.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 176 Answers

You have to look for a short in the can tkae a longtime to find th short or maybe you're one of the lucky people.

Good luck

Posted on Dec 31, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Cigarette lighter fuse continues to blow immediately after inserting a new one. Why?

It could be shorting behind the fuse panel or the ground is actually going to hot. Trace the ground and make sure it is well connected.

Nov 04, 2015 | 2003 Pontiac Aztek

1 Answer

Saturn vue batter boiling blowing relays

what is an ignition relay, ?
did you blow fuses?
what fuels, and battery boiling (running or not?)
running boil , would be overcharging , a bad alternator, or wiring to same.
not running boiling is crazy levels of battery loads.
if in my shop, out comes the AMPclamp meter, to find out
who is sucking extreme currents. and why fuses are not blowing
did some (#@!$) put in over size fuses, inviting a nice fire?
but if you have no tools? what can you do.
little, hold wet finger in air?
you could disconnect things and stop the drain
put them back 1 at a time (days work) an find the part that sucks
too much juice.

send photo with finger pointing to said relay.

Oct 12, 2013 | Cars & Trucks

1 Answer

1991 toyota 4runner efi fuse keeps blowing

Correct pump for the truck?
A blown fuse means there is too much current draw from the pump.
Why is the tough question.Pinched wire?
If the fuse does not blow,immediately,can you measure the current draw at the pump in put wire?

Be SURE to cycle the key on for 5 seconds,off for 2 and back on for 5 seconds 3 times! Prime the pump.
If not primed,properly the new pump may burn out.

Feb 22, 2013 | 1991 Toyota 4Runner

2 Answers

30amp AM 2 fuse blows as soon you turn on the key & car will not start

This is common about this time on these Camrys. I own three. The AM2 fuse is blowing because a coil, capacitor, or supressor has gone bad in the distributor. To test this disconnect the two wire connectors to the distributor. Replace the AM2 fuse. Turn the ignition. If the fuse doesn't blow. The distributor.

Jul 01, 2012 | 1994 Toyota Camry

1 Answer

EMC1 fuse keeps blowing immediately in 02 chevy express 3500LS 5.7L engine

That fuse powers the pink wire that runs to the coil, injectors, and pcm.
If the short isn't obvious, I disconnect everything I can from the wire and then put in a fresh fuse. I turn the key on and check the fuse. If it blows, I know it's something I haven't disconnected or the wire itself. If it doesn't blow, I start reconnecting things one at a time untl the fuse blows again.




Oct 02, 2017 | Cars & Trucks

1 Answer

Fuse 10 that conacts my raido and interior lights ECT keep blowing every tim i put one in

You have a SHORT CiRCUiT problem and only ur Auto Electrician can pinpoint where it is! The wire going to ur DOME light might have splintered and touch the body ground! The STEREO might have problem in its amplifier and power line thats why it kept blowing ur 10amp FUSE! Hope that might help u out! Taah!

Nov 15, 2010 | 2000 Dodge Stratus

1 Answer

I have a 2001 Ford Escape and recently it has been blowing both the break light and hazard/flashers fuses. It started with the break light fuse leaving me stranded in a drive through for an hour because I...

There is a shorted wire in somewhere in the circuit. The problem is where. You can use an ohmmeter and trace all your wiring or use a voltmeter and find a light socket that doesn't measure up to the rest or has inconsistent voltage readings. Make sure the fuse is not smaller than the origional

Dec 09, 2009 | 2001 Ford Escape

1 Answer

Radio Fuse blows

any time a battery is hooked up backwards anything that contains diodes will have to be replaced.unplug the radio and see if you can put the fuse in without it blowing.when you get the vehicle going have the alternator tested,it also has diode in it.good luck.

Sep 30, 2009 | 2000 Nissan Xterra

1 Answer

Alpine raido 2001 lincoln blows fuse soon as you put it in wires look ok. ???

There may be loose connections on wires or bad or loose ground.
As a stereo installer myself, I recommend wiring and installing with fuse out. Wait until everything is done before plugging in fuse!

May 10, 2009 | 2001 Lincoln LS

1 Answer

Blowing 30 amp engine control fuse.

You say it eventually allows you to put new fuse in, do you mean when it sits for a while, a new fuse won't blow, but if it blows and you immediately replace it, it blows again instantly?

Sep 05, 2008 | 1997 Dodge Ram 1500 Club Cab

Not finding what you are looking for?
2001 Lincoln Navigator Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts


Level 3 Expert

77499 Answers


Level 3 Expert

5608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides