Question about Honda Accord

2 Answers

I'm trying to remove the heater blower motor on Honda Accord I've removed the glove compartment and several screws but it seems to be hung-up on something on the back

Posted by on

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Honda Master
  • 329 Answers

I'm trying to remove the - 30e64e8.png
f38da4e.png
3f0119e.png

84eb4bd.png
a932a1b.png

4. Install in the reverse order of removal, and make sure there are no air leaks.

Posted on Dec 31, 2008

  • Level 1:

    An expert who has achieved level 1.

    Governor:

    An expert whose answer got voted for 20 times.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 4 Answers

There are three screws holding the blower motor in and they are upside down. There may be a black kick panel you have to you have to remove.

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

3 Answers

My fan blower motor only works on high,They say it maybe the resistor may be bad, where is it ? Thanks, Jim


Hi, the resistor is screwed to the side of the blower housing behind the glove box. See procedure below to replace the resistor. You don't have to complete all steps in the procedure. just work your way to the point that you can unscrew the resistor. Please let me know if you have questions, and thanks for using FixYa.

1990-93 Accord

See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)

jturcotte_1481.gif

Fig. Fig. 2: Remove the glove box and frame

  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.

  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
jturcotte_1482.gif

Fig. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully


jturcotte_1483.gifjturcotte_418.jpg

Apr 04, 2011 | 1993 Honda Accord

2 Answers

I cant find the blower motor


If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame 86806004.gif

  4. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  5. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 86806005.gif
      Fig. 4: Remove the lower covers from the blower unit 86806006.gif
      To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.
1988-91 Prelude
  1. Disconnect the negative battery cable.
  2. Remove the glove box and frame (lower support).
  3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws 86806007.gif

  4. Remove the 3 mounting bolts.
  5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
  6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

Jan 08, 2011 | 1992 Honda Accord

1 Answer

Need to replace heater blower motor. How do I get to it?


Behind the glove box. Please see my tip at http://www.fixya.com/cars/r6234839-doesn_t_heater_or_air_conditioner_blow . These are generic instructions. If you get stuck, please get back to me.

See instructions from autozone.com below.


REMOVAL & INSTALLATION


With Air Conditioning
See Figures 1, 2 and 3

  1. Disconnect the negative battery cable.
  2. Remove the glove compartment door and glove compartment.
  3. Disconnect the blower motor wires from the blower motor resistor.

jturcotte_62.gif
Fig. Fig. 1: Disconnect the blower motor wires from the blower motor resistor-1988 Escort
  1. Loosen the instrument panel at the lower right-hand side prior to removing the motor through the glove compartment opening.
  2. Remove the blower motor and mounting plate from the evaporator case.
  3. Rotate the motor until the mounting plate flat clears the edge of the glove compartment opening and remove the motor.
  4. Remove the hub clamp spring from the blower wheel hub. Then remove the blower wheel from the motor shaft.
jturcotte_63.gif
Fig. Fig. 2: Unbolt the mounting plate from the case


jturcotte_64.gif

Fig. Fig. 3: The motor can now be removed from the case


To install:

  1. If removed, assemble the blower wheel to the motor shaft and install the hub clamp.
  2. Install the motor and blower wheel assembly.
  3. Secure the instrument panel at the lower right-hand side.
  4. Connect the blower motor wires at the blower motor resistor.
  5. Install the glove compartment door and the glove compartment.
  6. Connect the negative battery cable.
  7. Check the system for proper operation.

Without Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the air inlet duct assembly.
  3. Remove the hub clamp spring from the blower wheel hub. Pull the blower wheel from the blower motor shaft.
  4. Remove the blower motor flange attaching screws located inside the blower housing.
  5. Pull the blower motor out from the blower housing (heater case) and disconnect the blower motor wires from the motor.

To install:

  1. Connect the wires to the blower motor and position the motor in the blower housing.
  2. Install the blower motor attaching screws.
  3. Position the blower wheel on the motor shaft and install the hub clamp spring.
  4. Install the air inlet duct assembly and the right ventilator assembly.
  5. Connect negative battery cable.
  6. Check the system for proper operation.

Nov 05, 2010 | 1989 Ford Escort

1 Answer

My 1988 Ford Tempo's heater fan is not working. I can feel heat at the windshield vents,but the fan wont come on. I have jumped the fan speed switch with a paper clip--and blew a fuse--and checked the...


your circuit is simple--I will paste it below. suspect the blower has shorted and caused the switch to burn up. remove the blower and hotwire it to the battery to see if it works. If not, replace the blower. Then run continuity tests on the swoitch and replace switch if bad. If you have questions, please let me know. Here is procedure for taking blower out:


REMOVAL & INSTALLATION With Air Conditioning

  1. Disconnect the negative battery cable.
  2. Remove the glove compartment door and glove compartment by removing the retaining screws and bolts. Push the sides of the glove box in to free the drawer from dash panel.
  3. Loosen the instrument panel at the lower right hand of the glove compartment opening. This is on it necessary if the panel is in the way of the motor housing.
  4. Remove the retaining screws securing the ducting around the blower motor.
  5. Remove the clip securing the blower motor fan blade to the motor arm. Remove the fan blade from the motor.
  6. Remove the blower motor mounting plate from the evaporator case by unscrewing the retaining screws.
  7. Rotate the motor until the mounting plate clears the edge of the glove compartment opening and remove the motor.
  8. Remove the wire harness from the rear of the motor.
  9. Inspect the fan blade for broken edges or cracks. Replace if needed.

To install:
  1. Connect the wire harness to the rear of the blower motor.
  2. Install the motor into the case and secure with the retaining screws.
  3. Position and fasten the fan blade to the blower motor arm. Secure with the clip.
  4. Secure the blower motor outer housing to the duct assembly with the retaining screws.
  5. Install the instrument panel at the lower right hand side if removed earlier.
  6. Install the glove compartment door and glove compartment.
  7. Connect the negative battery cable.
  8. Run blower motors to make the motor works correctly.
Without Air Conditioning
  1. Disconnect the negative battery cable.
  2. Remove the right ventilator assembly.
  3. Remove the hub clamp spring from the blower wheel hub. Pull the blower wheel from the blower motor shaft.
  4. Remove the blower motor flange attaching screws located inside the blower housing.
  5. Pull the blower motor out from the blower housing (heater case) and disconnect the blower motor wires from the motor.

To install:
  1. Connect the wires to the blower motor and position the motor in the blower housing.
  2. Install the blower motor attaching screws.
  3. Position the blower wheel on the motor shaft and install the hub clamp spring.
  4. Install the air inlet duct assembly and the right ventilator assembly.
  5. Connect negative battery cab
  6. Check the system for proper operation.

36d4b25.gif

Oct 21, 2010 | 1988 Ford Tempo

1 Answer

How to replace a blower motor in a 1996 ford thunderbird lx


Removal
  1. Remove the glove compartment liner to gain access to the heater blower motor and blower motor wheel assembly mounting screws.
  1. Use a small screwdriver to remove clip retaining hydraulic damper strut.
  1. Remove four screws and remove the heater blower motor assembly and blower motor wheel assembly from the heater blower motor housing.
Installation
  1. Using a new seal, position the heater blower motor and blower motor wheel assembly to the heater blower motor housing with the flat side of the flange near the heater blower motor switch resistor (18591). Install the four retaining screws.
  1. Tape the heater blower motor power lead to the air inlet duct to keep the wire away from the blower outlet during installation.
  1. Install the heater blower motor and blower motor wheel assembly in the vehicle.
  1. Install the glove compartment liner.

Oct 07, 2010 | 1996 Ford Thunderbird LX

1 Answer

Blower motor 1991 honda accord ex


the blower motor is located behind and under the glove box. its held to the blower housing by three screws. remove the three screws and the motor will slide down and towards you. to test the motor. apply power to the yelllow/black wire and ground to the blue/red wire. the motor should run. if not you prob have a faulty power resistor. 0881be0.jpg

Mar 06, 2010 | 1991 Honda Accord

1 Answer

How do i replace the heater blower motor


Remove the glove box.Then remove the glove box lower frame.The blower motor will be on the
right hand side under the dash.Remove three 10 mm screws.After removing the screws pull the
blower motor forward and up.There will be three harnesses connected in the lower right side
of the blower.

Nov 06, 2009 | 1992 Honda Accord

2 Answers

How do you replace the blower motor on 92 accord wagon - where is it located?


Disconnect the negative battery cable (if you have an anti-theft radio, make sure you have the code).
The blower unit is located in the dash, behind the glove box.
Remove the glove box and the glove box frame(damping screws on the sides and two screws underneath).
If the car isn’t equipped with air conditioning, remove the heater duct between the heater core and the blower assembly housings. Then remove the three blower housing retaining nuts, pull the blower housing out far enough to unplug the electrical connectors (at the lower right edge, right above the kick panel) and remove the blower assembly housing.
If the car has air conditioning, remove the strap bolt, the blower under cover and the three blower housing retaining nuts, then remove the blower assembly as previously described.
If you are replacing the blower motor itself, or either of the blower fan wheels, remove the motor, remove the retaining clip(s) and remove the fan wheel(s).
Reverse procedure to install.
Hope this helps you.

Oct 19, 2009 | 1992 Honda Accord

2 Answers

Honda Civic heater / blower noise.


Under glove compartment passenger side there is 4 screws that holds the blower in place loosen them and you will access the blower to clean it out.

Dec 11, 2008 | 2004 Honda Accord

1 Answer

Air and heater


  1. Disconnect the negative battery cable.
  2. Remove the glove box.
0900c1528005f9e2.jpgFig. 1: The blower motor assembly is secured to the right side of the dashboard
  1. Remove the duct between the blower and heater box.
  2. Unplug the wiring connector and the vacuum hose from the blower.
  3. Remove the three mounting bolts and remove the blower assembly.
  4. Install in reverse order, tightening the mounting bolts to 7 ft. lbs. (10 Nm). Make certain the blower mating surfaces are tightly sealed. Install the blower duct; make certain there is no leakage at its joints.
1990-93 Accord
See Figures 2, 3 and 4
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support)
0900c1528005f9e3.jpgFig. 2: Remove the glove box and frame
  1. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  2. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly.
0900c1528005f9e4.jpgFig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 0900c1528005f9e5.jpgFig. 4: Remove the lower covers from the blower unitTo install:
  1. Install the blower unit and tighten the retaining nuts.
  2. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  3. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  4. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  5. If applicable, enable the SRS.
  6. Connect the negative battery cable.

Oct 16, 2008 | 1990 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...