Question about 2000 Ford Windstar

1 Answer

2000 ford windstar, directionals both not working, hazards work f

The directionals on my 2000 Ford windstar stopped working, one right after the other. But my hazards still work fine. The fuses for the directionals are still good.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Turn signal flasher module or turn signal switch. I usuall try to wiggle teh column switch or move it slowly up and down, back and forth to help determine if it has a bad contact. if i cant get a failure (or turn signal) that way I begin the testing at the base of the column. the flasher module is a common failure on those and isnt unreasonably priced. if i had no diagnostic procedure i would try that first. oh yea, try turning the hazards on and off rapidly several times. the signal goes through the four way switch.

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Repair front directionals, hazards and high and low beams 2000 ford windstar


You probably have lost your ground. Check ground straps going from firewall to engine block. Then follow through and verify at the lights and look for exposed or corroded wires.

Jan 15, 2014 | 2000 Ford Windstar

1 Answer

Why does my 2000 ford windstar blow heat when moving but soon as i stop it is cold


Is it your blower motor work when moving and when you stop or there is no heat only?

Nov 29, 2013 | 2000 Ford Windstar

1 Answer

Some electrical problem


Why don't you suspect the ignition switch ?

Aug 22, 2012 | 2000 Ford Windstar

1 Answer

Need fuse lay out for a 2000 ford windstar. milage


Go to a local library and check out the Chilton series for 2000 Ford Windstars.
Good luck... its a Ford.

Jun 16, 2010 | 2000 Ford Windstar

1 Answer

Flashing ligth not working at all


Hi!!!

If your hazard lights turn on but do not blink, replace flasher.

If your hazard lights don't turn on, check hazard/stop/turn fuse(s).

Let me know how it worked out, good luck.

Mar 26, 2010 | 1998 Ford Windstar

1 Answer

2000 ford windstar 3.8L Front heater has


what stopped? the air doesnt blow,if thats the case then replace the blowermotor resistor, its located on heater box on passengerside next to blower motor.hope this helps, let me know if this was the problem.

Dec 24, 2009 | 2000 Ford Windstar

3 Answers

I have a 2000 ford winstar with a code 1131 what


This has to do with your bank one O2 sensor. You may just need to clean it off, possible you may have to replace it.

Nov 06, 2009 | 2000 Ford Windstar

1 Answer

Signal / hazard lights not working


THE RELAY MODULE IS BEHIND THE GLOVE BOX

May 04, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
2000 Ford Windstar Logo

Related Topics:

336 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60667 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21936 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...