1999 Ford Taurus Logo
Posted on Dec 31, 2008
Answered

Where on line can i find a diabram of a front wheel bdaring on a 1998 ford taurus. I need to change one

Answer This Question

2 Answers

Michael York

Level 1:

An expert who has achieved level 1.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.
Problem Solver:

An expert who has answered 5 questions.

  • Contributor 7 Answers
  • Posted on Jan 03, 2009
Michael York
Contributor
Level 1:

An expert who has achieved level 1.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.
Problem Solver:

An expert who has answered 5 questions.

Joined: Jan 03, 2009
Answers
7
Questions
0
Helped
5054
Points
13

Go to autozone.com they have repair manuals on their web site

Anonymous

Level 1:

An expert who has achieved level 1.
Hot-Shot:

An expert who has answered 20 questions.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.

  • Contributor 22 Answers
  • Posted on Dec 31, 2008
Anonymous
Contributor
Level 1:

An expert who has achieved level 1.
Hot-Shot:

An expert who has answered 20 questions.
Corporal:

An expert that has over 10 points.
Mayor:

An expert whose answer got voted for 2 times.

Joined: Dec 11, 2008
Answers
22
Questions
0
Helped
7311
Points
53

Not sure that you can find a diagram with out paying for it but if you take off the front wheel and brakes caliper ,rotor, there will be a big nut in center of lug nuts remove it then on the back side of spindle there will be either 3 or 4 mounting bolts holding in bearing remove those and unplug ABS sensor if equiped then use a hammer to seperate bearing (hub assembly) from spindle good luck

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

Panel that goes under ford taurus engine what does it screw into
take a look at the panel and you will see where the holes for screws are, when you line it with where it is suppose to go the holes will be where it screws.
Read full answer
Apr 14, 2014 • 1998 Ford Taurus
0helpful
1answer

Is my 98 ford taurus rear wheel?
If you want to know if it is rear wheel drive, then I would say no. It is front wheel drive. One can tell by looking at the halfshafts that lead to the wheels in the front vs. the back wheel area.
Read full answer
Dec 14, 2010 • 1998 Ford Taurus
0helpful
1answer

My 98 Taurus has alot of play on front driver side wheel not sure if the ball joints or bearing is bad is there a way to tell.
When jacked up if you can move wheel excessively it is probably wheel bearing.
Read full answer
Jul 23, 2010 • 1998 Ford Taurus
5helpful
1answer

LOUD CLUNKING NOISE IN REAR WHEEL AREA WHEN TURNING LEFT
sounds like either a sway bar end link or shock, more towards the end link tho
Read full answer
Feb 24, 2010 • 1998 Ford Taurus
1helpful
1answer

Alternator removal 1998 ford taurus dohc
3.0L (4V)
Removal
  1. Disconnect the battery ground cable.
  1. Remove the accessory drive belt from the generator pulley.
  1. Remove the power steering line bracket and heater hose support bracket from the generator.
  1. Remove the upper generator bolts.
  1. Partially raise the vehicle on a hoist.
  1. Remove the right front wheel.
  1. Remove the lower fender splash shield retainers and position the shield out of the way.
  1. Remove the generator splash shield.
  1. Raise the vehicle.
  1. Disconnect the electrical connector and remove the battery positive cable from the generator.
  1. Position an adjustable stand to the subframe.
  1. Remove the right subframe bolts.
  1. Remove the lower generator bolt.
  1. Lower the subframe to provide clearance.
  1. Remove the generator.
Installation
  1. NOTE: Do not tighten the lower bolt.

    Install the generator and the lower bolt.
  1. Raise the subframe and install the subframe bolts. Tighten the bolts to 90 Nm (66 lb-ft).
  1. Remove the adjustable stand.
  1. Lower the vehicle.
  1. Install the upper generator bolts and tighten them to 25 Nm (18 lb-ft).
  1. Install the power steering line bracket and the heater hose support bracket. Tighten the nut to 20 Nm (15 lb-ft).
  1. Install the accessory drive belt. Refer to Partially raise the vehicle.
  1. Tighten the lower generator bolt to 25 Nm (18 lb-ft).
  1. Connect the generator electrical connector.
  1. Install the battery positive B+ cable and nut. Tighten the cable nut to 10 Nm (89 lb-in).
  1. Install the generator splash shield.
  1. Install the fender splash shield and the retainers.
  1. Install the right front wheel.
  1. Lower the vehicle.
  1. Connect the negative battery cable.
Read full answer
Nov 08, 2009 • 1998 Ford Taurus
0helpful
1answer

It's a 98 Taurus, Wagon, the brake fluid line leaks
common problem, youll need a flare kit. and some brak line,unions, find a good spot of line in frt, and cut , remove other end at hose, then flair frt, make line the size you need install and bleed system, then check for leaks good luck,
Read full answer
Oct 14, 2009 • 1998 Ford Taurus
0helpful
1answer

My 1998 Ford Taurus has a charged a/c and the compressor works bu blows only hot air
is the condensor comming on, does the idle change when it comes on? watch the front of the compressor and have some one turn it on and watch the center wheel if it doesn't start moving it is not working even if it has a charge the compressor could be bad
Read full answer
Jun 06, 2009 • 1998 Ford Taurus
0helpful
1answer

Rear brake lines 99 ford taurus se
most of the time the auto parts can give you the right length.but if i had to gess your looking at 6to 7 feet long 8 ft at the most. it would be a good i dear to re place the line going to each wheel to . because those will be the next one to go good luck
Read full answer
Apr 19, 2009 • 1998 Ford Taurus
0helpful
1answer

Ford taurus 1998 brakes
it could be two things: you have a bad check valve in the master cylinder or the calipers themselves are bad
Read full answer
Apr 02, 2009 • 1998 Ford Taurus
0helpful
2answers

Brake Line Broke
metal
Read full answer
Jan 17, 2009 • 1998 Ford Taurus
Not finding what you are looking for?

View Most Popular

1999 Taurus

  • Cars & Trucks

Related Question

Panel that goes under ford taurus engine what does it screw into

  • 1998 Ford Taurus

Related Topics

345 views

Ask a Question

Usually answered in minutes!

Popular Questions

Diagram of fuse box 2000

2000 Ford Taurus

2005 ford taurus fuse box diagrams

2005 Ford Taurus

Fuse box diagram for 2002 ford taurus

2002 Ford Taurus

I turn key and starter spin but will not engage flywheel.

2005 Ford Taurus

Serpentine belt diagram 2002 ford taurus 3.0

2002 Ford Taurus

Check Out the Latest Top Trucks Report!
Check Out the Latest Top Trucks Report!

View all Fixya Reports

Top Ford Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...