Question about 1989 Mazda MX-6

1 Answer

Brake fluid leaking

Its leaking in to my car while its parked and i hav to replace clutch and brake fluid everytime i drive, i also have to pump brakes in order to stop i tried having my brakes bled and that just seemed to make it worse help what do i do?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 112 Answers

It looks a faulty brake pump, to check it- have some one else with you to watch the pump fluid while you are pumping the brake pedal, if there is an air bubble come up the fluid then you should change the brake pump or kit.

Posted on Jan 14, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1990 Honda EX clutch. It does not ingage. It pops to the top or sticks to the floor


Not sure of the model EX, but it probably has a clutch hydraulic slave and master cylinder that has leaked out the hydraulic fluid. Fill the clutch master cylinder (near the brake master cylinder) with brake fluid and pump the clutch pedal several times. The clutch work again until the fluid leaks out, so the permanent fix is to replace the master and or slave cylinders and bleed the system. Other models have a clutch cable that would need replacing in this case

Oct 24, 2017 | Honda Cars & Trucks

2 Answers

Ford transit 52 plate clutch pedal goes soft then csnt change gear then pump pedal pedal goes back to normal drive for a short while then clutch pedal goes soft again and just repeats as above just bought...


The clutch hydraulic system has a problem-either the clutch master cylinder or the slave cylinder on the bell housing may be at fault.

If the brake fluid is low in the clutch master cylinder reservoir, there may be a leak to the outside. Refill and check for leaks while someone pumps the clutch pedal. Check around the clutch master cylinder (also under the dash- if wet there around the top of the clutch pedal or if wet on the carpet below the pedal, the master cylinder is leaking.) Check the single line from the clutch master to the bell housing where the slave cylinder is. If no leaks found, likely the clutch master cylinder or the slave cylinder has failed internally.

Is it safe: there won't be any further damage caused by running it, but if shifting gets harder and harder to do, that may cause a driveability problem.

Jun 24, 2014 | Cars & Trucks

2 Answers

Power Steering reservoir leaking and dripping on Serpentine Belt, possible cause of loose belt movement (has come off once already). Wobble of A/C Pulley, resulting in A/C not cooling.


Power steering pump shaft seal is leaking, You can add a table spoon of DOT 3 brake fluid to the steering fluid to condition the seal. The A/C pulley wobble is a compressor clutch bearing problem and requires the correct puller to replace. Replace the clutch as a unit, to avoid messing with the bearing. Replace the belt if the steering fluid leak stops. If the brake fluid trick does not work, replace the steering pump. Parts and labor will be better than 200.00

Aug 25, 2017 | 1999 Plymouth Grand Voyager

1 Answer

I have a 93 Mazda mx6 Ls... Everytime I step hard


When my MX6 was doing this it turned out to be an hydraulic leak from the clutch master cylinder, which runs on the same fluid reservoir as the brakes. Clutch master cylinder replaced and all good again!

Apr 10, 2012 | 1993 Mazda MX-6

1 Answer

Where is the clutch auto adjustment located at on a 98 manual Volkswagen jetta?


you most likely have a hydraulic clutch, which the clutch master cylinder is located on the firewall on the driverside close to your drivers side windsheild.it takes brake fluid to fill dot brake fluid will fill it properly. however if your slave cylinder on the transmission is leaking,this will require a replacement of the clutch slave cylinder. look for leakage under passenger side,,just under or below passenger side seat onto ground. recommend if you replace the clutch slave cylinder,you also replace clutch master cylinder located on the drivers side firewall at wind sheild.look under the car while someone pumps the clutch in and out,if you see brake fluid leaking under car onto ground or inside onto carpet at brake pedal,you have a bad clutch master cylinder. recommend you replace both slave cylinder and clutch master cylinder. this will save you lots of time and headaches. thank you for choosing fixya.com

Sep 24, 2011 | 1998 Volkswagen Jetta

1 Answer

Clutch pedal has no pressure and goes straight to the floor when pressed. clutch disk is in good condition. parked the car the night before was working perfect. next morning no pressure and out of fluid....


Pump the clutch pedal and then check for leaks again, including under the dash where the rod from the pedal goes into the clutch master cylinder. Once you find the leak, replace what's leaking and bleed the system to restore the pressure (bleeds from the slave unit, just like bleeding brakes)

May 30, 2011 | 1996 Honda Civic

3 Answers

I Push my clutch down and has no resistance, i also cannot get the car in and out of gear. I drive a 1995 3000gt SL.


the clutch is hydraulic . you need to look on the fire wall for a reservoir . and fill it look on the cap it will tell you what fluid to use . after you refill it pump the clutch a few times the wait 5 minutes and pump it again . check the fluid again pump again if the fluid is leaking out you'll have this trouble again till you fix the leak.

Mar 16, 2011 | 1995 Mitsubishi 3000GT

2 Answers

1989 mazda mx6 brake fluid leaking


You have a leak in the master cylinder. If brake fluid is leaking into the vehicle I would say I have not heard of this problem before but anything is possible anyway the likely problem is the master cylinder is worn and leaking fluid and air - that's why you have to puimp the brakes. It really isn't that expensive if you provide the parts once it is diagnosed - you really should get it repaired right away though because they can go out completely without warning. Hope this helps.

Dec 31, 2008 | 1989 Mazda MX-6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

114 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...