Question about 1990 Acura Integra Hatchback

1 Answer

Trying to find out what the special bolt is on the crankshaft on my 1990 acura integra

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Bro., what do you mean in the crankshaft? just go to pick n pull and put it in your pocket and walk out.

Posted on Feb 22, 2009

2 Suggested Answers

txkjun
  • 409 Answers

SOURCE: special bolt on the crankshaft pully on 1990 acura integra

It should be a hex bead bolt. Nothing really special about the. If its a bolt that is torqued then tightened to a specific angle then you need to replace it when doing the work.

Posted on Dec 31, 2008

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch pedal is to high


There may be an adjustment bolt, called a stopper bolt, at top of pedal. Screw it out and pedal height will change.
Good luck.

Jan 08, 2012 | 1990 Acura Integra Hatchback

1 Answer

Im replace a head on a 1990 acura integra b18a engine can i reuse the same head bolts


no, always use new head bolts/head studs
Acura recommends this at every head gasket service unless previously replaced at last head gasket service....
I reccomend ARP head studs or equivalent quality

Sep 01, 2010 | Acura Integra Cars & Trucks

1 Answer

How to set the timeing on 1990 acura integra


YOU NEED TO CONNECT A TACHOMETER ACCORDING TO THE MANUFACTURERS INSTRUCTION.ON THE 1990 - 1993 MODELS USING A SUITABLE JUMPER WIRE CONNECT THE GREEN AND BROWN TERMINALS OF THE IGNITION TIMING ADJUSTING CONNECTOR LIGHT GRAY WIRE LOCATED UNDER THE RIGHT SIDE OF THE DASH.MAKE SURE ALL WIRES CLEAR OF THE COOLING FAN AND HOT EXHAUST MANIFOLDS.START THE ENGINE POINT THE TIMING LIGHT AT THE TIMING MARK POINTER AND THE CRANKSHAFT PULLEY.ON THE 1990 - 1993 MODELS THE POINTER SHOULD BE ON THE RED MARK 16 DEGREES BTDC ON THE CRANKSHAFT PULLEY AT 700 - 800 RPM.IF NECESSARY ADJUST THE TIMING BY LOOSENING THE DISTRIBUTOR ADJUSTING BOLTSSLOWLY ROTATE THE DISTRIBUTOR IN THE REQUIRED DIRECTION WHILE OBSERVING THE TIMING MARKS.AFTER MAKING THE NECESSARY ADJUSTMENT TIGHTEN THE HOLD DOWN BOLTS TAKING CARE NOT TO DISTURB THE ADJUSTMENT.REMOVE THE JUMPER WIRE.

Feb 28, 2010 | 1990 Acura Integra Hatchback

1 Answer

Do I need a special tool to install a crankshaft timing gear on a 1994 acura integra gsr


get a book from auto parts store on your car. its a must have for deep repairs. it will tell you what tools to use. good luck. joeyj35@live

Feb 12, 2010 | 1994 Acura Integra

1 Answer

I'm trying to replace the power steering pump on my acura integra 1994 how can i replace it


drain power steering fluid.disconnect the inlet and out let hoses from power steering pump.remove belt by loosen the adjusting bolts on pump bracket.remove power steering bolts and remove pump.put in new power steering pump torque it 17 ft lbs . connect hoses .put belt back on adjust the belt tension. add fluid check level . bleed the air from system.

Apr 13, 2009 | 1990 Acura Integra Hatchback

1 Answer

Special bolt on the crankshaft pully on 1990 acura integra


It should be a hex bead bolt. Nothing really special about the. If its a bolt that is torqued then tightened to a specific angle then you need to replace it when doing the work.

Dec 30, 2008 | 1990 Acura Integra Hatchback

1 Answer

Crankshaft pulley


no it doesnt,to undo fit a appropiate socket and using a big knuckle bar wedged in suspension turn starter motor to undoo the bolt

Dec 14, 2008 | 1990 Acura Integra Hatchback

1 Answer

Belt replacement 1990 acura integra


Ok, you will need a 10 mm socket and extension and a 14 and 15 mm wrench. One of the "idler" pullies is actualy an adjustable tension pully. loosen the center nut on the pully, and then begin loosening the 10 mm bolt from above. as you loosen it, the pully will drop, and soon enough you can slip the belt off.
good luck

Dec 14, 2008 | 1990 Acura Integra Hatchback

1 Answer

1990 Acura Integra Vin codes


The vehicle grade is denoted in the 6th digit, in your case "4" indicates an RS model.

Oct 19, 2008 | 1990 Acura Integra Hatchback

Not finding what you are looking for?
1990 Acura Integra Hatchback Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Acura Experts

yadayada
yadayada

Level 3 Expert

64052 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you an Acura Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...