Question about Hyundai XG300

1 Answer

Gearbox not comeng out from engine housing - XG300 Hyundai Cars & Trucks

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thewre is a bolt on the throw out bearing pivot which must be taken out

Posted on Dec 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm replacing the clutch. I have removed all the bolts and separated the the housing slightly but cannot totally separate the two. I'm thinking I may be missing a step.


in the same area of the bolt wholes there will be dowels sometimes the gearbox just needs to be pryed to seperate also make sure the driveshafts are completely removed from the gearbox shift cables and hydraulic line is removed mountings are removed completely out of the gearbox way.sometimes the loom or water hoses routed over the gearbox can restrict and its common for the cv joint flange on the gearbox differential to hook on the metal shim plate thats sandwiched between the engine and gearbox

Mar 16, 2016 | 2002 Kia Sportage

1 Answer

How to remove 1400 Nissan gearbox out


1 Remove battery earth cable.
2 Remove gear shift lever - usually just pulls out.
3 Remove starter motor.
4 Remove bolts holding prop shaft to gearbox final drive, and remove the prop shaft.
5 Remove all bolts around bell housing holding bell housing to engine.
6 Slide gearbox back to slide spigot shaft from clutch plate.
7 Slide gearbox from under vehicle.
Gearbox is now removed out.

Jan 02, 2015 | Nissan Cars & Trucks

2 Answers

Water leaks where engine and transmission connect, looking from the passenger side under the truck.


thats sounds like a core plug has blownout or rusted through,have to split engine from gearbox to gain access to the rear of engine block but first make sure its not above where gearbox housing butts to engine ie may have a higher core plug or a split hose ,

May 08, 2014 | 1993 Chevrolet S-10

1 Answer

Toyota caldina specifications


I suggest you get the gearbox model number. Could be on the plate under the bonnet or on the gearbox housing.

Jan 15, 2014 | Cars & Trucks

1 Answer

Hurth gearbox manual


Perkin engines were built to a standard bell housing configuration so that gear boxes of different makes would fit straight on. If you hurth gear box was made to these standards then the bell housing will bolt up to the engine. It was no 1 for most gear boxes or no2 for road ranger -splicer . Check with an engine rebuilder rand they will be able to tell you.

Nov 10, 2013 | Cars & Trucks

1 Answer

Cruise contol wont work


if your light comes on then check vac lines comeng off the cruse

Jun 24, 2012 | 1996 Honda Accord

1 Answer

Ive got a 94 firebird with bad freeze plugs how much should it cost to replace


Gday mate,geoff here, well yes i think you should, as they keep the coolant in, now if they are bad, you will find the worst one in the bell housing which means engine/gearbox out to replace, the ones on the side are easy, but make sure before you do remove either engine/gearbox that there really is one in the back of the engine block inside the bell housing, for if you replace the ones you can see then the weak link will be the one(s) that you couldn't see, hope this helps, geoff.

Feb 09, 2012 | Pontiac Cars & Trucks

1 Answer

If the clutch slave cylinder on my 2005 Saturn Vue is internal to the transmission, how would the fluid have poured out onto my garage floor? I think the transmission dude might be pulling my leg to the...


No its internal meaning that its in the bell housing.The bell housing is bolted to the gearbox to hous the clutch befor being bolted to the engine.It has no seal on it.So when your slave cylinder leaks,The fluid drips from the bell housing.And the only way to get at it is to remove the gearbox.

Jul 17, 2009 | 2005 Saturn VUE

1 Answer

Is the bell housing bolt pattern on a 1980 Ford escort the same as a cortina gearbox?


Yes, the splines are bigger on the 1.6 and up gearboxes on both the input and output shafts

May 30, 2009 | 1983 Ford Escort Gt

1 Answer

Gearbox removel mazda 626 1991


yes, that is what you do. You are almost there, keep going.

Feb 27, 2009 | 1991 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

45 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60867 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...