Question about 1997 Lincoln Continental
Service eng lite on, an abs lite on,scan system got u1039 speed signal invalid or missing,and no abs code in system,replaced speed sensor,wheel abs sensor,turbine shaft speed sensor,sent instrument cluster repaired,and now still have same problem odmeter not showing speedometer inop,intermitantly,has too turn off vehicle and restart to get odometer signal.
check the relays under the kick panel on drivers side...maybe switch them around and see if that works....sometimes corrolas will do the same thing.check the ones under the hood also.
Posted on Jul 25, 2009
same problem with 95 looking for answer
Posted on Sep 23, 2009
The switch contacts are probably dirty. They can be cleaned if you can remove the switches without disassembling the door. Not familiar enough with the Suburban to know how easily this can be done.
Posted on Oct 10, 2009
Having the same problem with my 2001 Merc Cougar, When does it black out? While reving or randomly? Mine is while heavy accelerating. Could be over voltage at the charging system (alternator or regulator) or internal in the cluster. Get the alternator and batt tested first, ask for a load test, then try the cluster next.
Posted on Dec 31, 2009
If it has no spark you might try to replace the ign. module by the drivers side hood hinge attached to fender . Bought this part at pull a part for less than ten dollars. Put it on and cranked right up. Be sure t seal the water out when replacing.
Posted on Apr 27, 2010
Tips for a great answer:
Sep 13, 2015 | 2004 Lincoln Aviator
Aug 21, 2015 | Cars & Trucks
Mar 14, 2015 | 2008 Lincoln Navigator
Review Strategy Based Diagnosis for an overview of the diagnostic approach.
Diagnostic Procedure Instructions provides an overview of each diagnostic category.
Conditions for Clearing the DTC
DTC C0561 71: System Disabled Information Stored Invalid Serial Data Received
DTC C0561 72: System Disabled Information Stored Alive Counter Incorrect
DTC C0561 74: System Disabled Information Value of Signal Protection Calculation Incorrect
The electronic brake control module (EBCM) receives serial data messages from the body control module (BCM), engine control module (ECM), instrument panel cluster (IPC), and the transmission control module (TCM) which are needed to perform antilock brake system (ABS), vehicle stability enhancement system (VSES), or traction control system (TCS) functions.
Conditions for Running the DTC
Ignition voltage is greater than 10 volts.
Conditions for Setting the DTC
The EBCM receives an invalid serial data message from another module.
Action Taken When the DTC Sets
The EBCM disables the traction control system (TCS)/ vehicle stability enhancement system (VSES).
A DIC message and/or a warning indicator may be displayed.
The condition for the DTC is no longer present.
The EBCM clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.
This DTC indicates that there are no problems in the EBCM. The BCM, ECM, IPC and the TCM should be checked for a possible fault.
Schematic Reference Antilock Brake System Schematics
Connector End View Reference Component Connector End Views
Description and Operation ABS Description and Operation
Electrical Information Reference ?€¢
Scan Tool Reference Control Module References for scan tool information
Conditions for Clearing the DTC
Sep 26, 2014 | 2007 GMC Acadia SLE
Feb 12, 2013 | 1998 Lincoln Continental
Oct 23, 2012 | 2001 Lincoln Town Car
Dec 23, 2011 | 2003 Lincoln LS
Jun 29, 2011 | 2001 Lincoln Town Car
Oct 09, 2010 | 1990 Lincoln Mark VII
Nov 06, 2009 | 1993 Lincoln Continental
Nov 17, 2015 | 1997 Lincoln Continental
Oct 11, 2015 | 1997 Lincoln Continental
587 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: