Question about 2002 Land Rover Freelander

1 Answer

Hard clutch pedal

I want to know how to bleed the servo unit on the landrover freelander as my pedal is very hard to press down

Posted by on

  • Anonymous Mar 12, 2014

    Clutch taking low, master and slave cylinders have been replaced, just need tips on how to bleed the system

  • Anonymous Mar 26, 2014

    servo not working

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 99 Answers

You cannot bleed a servo. it runs using the vacuum from either inlet manifold, or a seperate vac pump.Ensure pump is working if fitted (end of camshaft) the pipes to the servo are not leaking by removing the pipe from servo and start veh. If there is good suction then its servo failure. hard pedals can also be caused by pressure plate fatigue in the clutch itself.

Posted on Jan 21, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The Clutch disc and Release Bearing for the TD4-Freelander, were replaced recently. The Pressure Plate was still in a good condition.Gears difficult to engage.Please advise.Tks.John.


Most likely still has air in hydraulic clutch slave system. Many transmisions will have dificulty shifting if clutch doesn't full disengage. If air is in system it won't allow full disengage thus difficulty in shifting even possible grinding gears

Sep 17, 2016 | 2002 Land Rover Freelander

1 Answer

Bleeding the clutch


2 people job. one presses down on the clutch pedal while the other opens the bleed screw. then closes of the bleed screw before the pedal operator lets the pedal up . The process is repeated until all the air is out . Watch the fluid level in the reservoir.

Mar 11, 2014 | 2006 Ford Bantam 1.3i

1 Answer

I replaced clutch slave n master cylinder it still dont keep pressure afta 2 days i must bleed agen


please state model of vehicle and year .Is the fluid level dropping ?not a landrover freelander by any chance

Nov 03, 2013 | Cars & Trucks

1 Answer

Won;t start while clutch pressed but will push start


The clutch master cylinder must have gone out, the seals in it have failed. The clutch master cylinder (next to the brake master cylinder) gives you hydraulic pressure so the clutch pedal can operate the clutch.
You can buy a new clutch master, a rebuilt unit, or yours can be rebuilt with new seals. Save time and money and buy a rebuilt or remanufactured unit. Once installed, you bleed the system down at the clutch slave cylinder, mounted on the transaxle.

Jul 15, 2013 | 1989 Honda Prelude

1 Answer

97 jeep Cherokee clutch will not depress to start the engine


Now you need to bleed the clutch at the clutch slave cylinder down on the transmission to restore the clutch.
Put a wrench on the bleed valve and open it, then lightly close it. Now have someone pump the clutch a couple of times to build pressure. Then while the clutch pedal is slowly pressed down open the bleed valve, then close valve as pedal gets to floor. Repeat this bleed process until a steady stream of brake fluid comes out the bleed valve. Then you should have a good clutch again.

Dec 20, 2012 | 1997 Jeep Cherokee

1 Answer

Is there air in my ABS of my '92 thunderbird lx?


ABS isn't so much a thing as a system, but if you want to know how to bleed your brake system you place a tranparent tube on one of the brake cylinder valves/nipples, then imerse the end of the tube in a small bottle with some brake fluid in. Then you get someone to press the pedal down slowly as you open the valve/nipple. They should pump a few times slowly, then with the pedal down close the valve/nipple. Check to see if the pedal is harder. You should do this with both front and rear brakes, as they are seperate lines. The ABS is a system that ballances the brakes to stop slewing across the road when you apply the pedal too hard. The part attached to the master cylinder is actually a servo, which should have a tube go from it to the inlet manifold of the engine. This causes a vacuum in the servo, which when applying the brakes helps the brakes by taking away some of the pressure needed. If this pipe is broken or not connected, then your sevo won't work. There is an easy way to check your servo. Press the pedal down, then start the engine, you should feel the pedal go down a bit more. If it does not, check the servo tube.

May 20, 2012 | 1992 Ford Thunderbird

1 Answer

Have freelander td4 03 plate, continuous problem with clutch. had new clutch , slave cylinder and master 2 months ago, all fine till a month ago lost pedal completely , had new master fittted problem fixed...


Definitely a hydraulic issue. Iknow you said they were both changed, but its usually the master & slave assembly that go faulty on the Freelander. Both parts come filled with fluid and pre-bled and only require fitting, no bleeding. Check with garage to make sure they did not split / bleed them.

Jun 06, 2011 | 2003 Land Rover Freelander

2 Answers

Pushing clutch pedal fully down &still difficult to obtain gears


Clutch plate is worn down to nothing and/or throwout bearing needs replaced.

Jul 29, 2009 | 2002 Land Rover Freelander

Not finding what you are looking for?
2002 Land Rover Freelander Logo

589 people viewed this question

Ask a Question

Usually answered in minutes!

Top Land Rover Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

yadayada
yadayada

Level 3 Expert

70365 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6878 Answers

Are you a Land Rover Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...