Question about 1990 Chevrolet Suburban

1 Answer

Coolant in exhaust pipe but not the oil

I am wondering what the pipe that runs from rear of drivers side exhaust to the front of intake manifold is, and if would cause antifreeze consumption thru the exhaust? 1996 chevy tahoe vortec v8

Posted by on

  • 2 more comments 
  • callahankell Dec 30, 2008

    It is running like it is missing on one cylinder, not bad just a miss. But will run all coolant out burning and dripping from tailpipe in 30 mins or so

  • lafi30 Jan 08, 2009

    I was losing coolant via exhaust manifold. I found the leak to be from a pipe that runs from somewhere near the thermostat housing all the way to the exhaust manifold. The problem is no one of the 6 mechanics I have visited including the dealership knew what was pipe for.
    Anyway, the dealership found it in their data base charts and told me it costs $116. I am waiting for the engine to cool down and going to take a shot on this by taking it out and see where the leak coming from, is it the connections or the pipe itself. If is the pipe, I think I'll be luck to find someone to braze it for me. If it is the connections, one of them is replaceable the other one, then I am up **** creek without the paddles.


  • Anonymous Mar 22, 2014

    Antifreeze in exhaust pipe

  • Anonymous Mar 30, 2014

    Hole about the size of silver dollar

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,450 Answers

THIS SOUNDS LIKE YOU ARE TALKING ABOUT EGR PIPE. AND NO IT WONT CAUSE COOLANT

Posted on Dec 30, 2008

  • TripleTauto
    TripleTauto Dec 30, 2008

    your coolant is coming from a cracked block,head, headgasket could alos be coming from intake gasket leaking into intake port is truck running rough?

  • TripleTauto
    TripleTauto Dec 31, 2008

    I believe you have a blown headgasket. the coolant passage is shooting a stream straight into one cylinder.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Will a bad upper intake manifold gasket on a 97


sounds more like a blown head gasget a compression test will tell you for sure

Sep 25, 2014 | Cars & Trucks

1 Answer

I need head bolt torque specs for a 2000 cadillac deville dts..


DeVille, Eldorado, Seville 1999-2005

Cylinder Head

Print


Removal & Installation

Left Side

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Alternator Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Power steering return hose retaining bolt from the cylinder head 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket.
  5. Clean the head mating surfaces.

To install:

0996b43f80231662.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Left cylinder head bolt torque sequence-4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees
    2. Step 2: Turn an additional 60 degrees
    3. Step 3: Turn an additional 60 degrees (total 190 degrees)

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm)
  4. Install or connect the following:

    Power steering return hose retaining bolt to the cylinder head and tighten to 37 ft. lbs. (50 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Right Side
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Properly relieve the fuel system pressure.
  4. Remove or disconnect the following:

    Negative battery cable Exhaust manifold Water crossover Intake manifold Valve cover Timing cover Secondary camshaft drive chain Electrical connector from the Engine Coolant Temperature (ECT) sensor Nut attaching the coil cassette ground wire to the cylinder head Bolt attaching the exhaust crossover pipe to the cylinder head Bolt attaching the right transaxle mount bracket to the cylinder head Bolt attaching the rear transaxle brace to the transaxle Nuts attaching the rear transaxle brace to the cylinder head Rear transaxle brace 3 M6 external drive bolts from the front portion of the cylinder head 10 M11 internal drive cylinder head bolts Cylinder head and gasket
  5. Clean the head mating surfaces.

To install:

0996b43f80231663.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Right cylinder head bolt torque sequence- 4.6L engine

  1. Install the cylinder head with a new gasket. Lubricate the bolts with engine oil prior to installation.
  2. Torque the M11 bolts in sequence as follows:
    1. Step 1: 30 ft. lbs. (40 Nm), plus an additional 70 degrees.
    2. Step 2: Turn an additional 60 degrees.
    3. Step 3: Turn an additional 60 degrees (total 190 degrees).

  3. Torque the M6 bolts to 106 inch lbs. (12 Nm).
  4. Install or connect the following:

    Rear transaxle brace over the studs located at the rear of the right cylinder head Nuts attaching the rear transaxle brace to the cylinder head, loosely Bolts attaching the rear transaxle braces to the transaxle and tighten to 37 ft. lbs. (50 Nm) Nuts attaching the rear transaxle brace to the cylinder head and tighten 37 ft. lbs. (50 Nm) Electrical connector to the ECT sensor Bolt attaching the exhaust crossover pipe to the cylinder head and tighten to 18 ft. lbs. (25 Nm) Nut attaching the coil cassette ground wire to the cylinder head and tighten to 13 ft. lbs. (17 Nm) Secondary camshaft drive chain Timing cover Valve cover Intake manifold Water crossover Exhaust manifold Negative battery cable
  5. Change the oil and filter.
  6. Fill the cooling system.

Apr 16, 2013 | 2000 Cadillac DeVille DTS

1 Answer

Wont start



Trouble Code: P0300

Multiple Cylinder Misfire Detected
Possible Causes:


Air leak in the intake manifold, or in the EGR or EVAP system Base engine mechanical fault that affects two or more cylinders Erratic or interrupted CKP or CMP Sensor signals Fuel delivery component fault that affects two or more cylinders (i.e., a contaminated, dirty or sticking fuel injector)


Trouble Code: P0432

Catalyst Efficiency Below Normal (Bank 2)
Possible Causes:


Air leaks in at the exhaust manifold or exhaust pipes Base engine problems (high coolant or engine oil consumption) Catalytic converter damaged or has failed Front O2 older (aged) than the rear O2 (O2 is lazy) Ignition system problem (coil or plug) in two or more cylinders Vehicle driven with low fuel pressure or while very low on fuel

Jul 06, 2012 | 1999 Dodge Intrepid

1 Answer

Intakegasket for grandam gt


Exactly what is the wrong? Need the part? Need to know torque adjust or porcedure to take off?

For
1994 Pontiac Grand Am 3.1L SFI OHV 6cyl check this procedure for Intake Manifold...
(see Figure 14)
The 3.1L engine is equipped with upper and lower intake manifolds. The upper intake manifold is also known as the intake manifold plenum.

CAUTION The fuel system is under pressure and must be properly relieved before disconnecting the fuel lines. Failure to properly relieve the fuel system pressure can lead to personal injury and component damage.
  1. Relieve the fuel system pressure.
  2. Disconnect the negative battery cable.
  3. Remove top half of the air cleaner assembly and throttle body duct.
  4. Drain and recycle the engine coolant.
  5. Disconnect the EGR pipe from exhaust manifold.
  6. Remove the serpentine belt.
  7. Remove the brake vacuum pipe at the intake plenum.
  8. Disconnect the control cables from the throttle body and intake plenum mounting bracket.
  9. Remove the power steering lines at the alternator bracket.
  10. Remove the alternator.
  11. Label and disconnect the ignition wires from the spark plugs and wire retainers on the intake plenum.
  12. Remove the ignition assembly and the EVAP canister purge solenoid together.
zjlimited_601.jpg

Fig. 14: View of the intake manifold and related components

  1. Disconnect the upper engine wiring harness connectors at the following components:
    Throttle Position Sensor (TPS) Idle Air Control (IAC) Fuel Injectors Coolant temperature sensor Manifold Absolute Pressure (MAP) sensor Camshaft Position (CMP) sensor
  2. Tag and disconnect the vacuum lines from the following components:
    Vacuum modulator Fuel pressure regulator PCV valve
  3. Disconnect the MAP sensor from upper intake manifold.
  4. Remove the upper intake plenum mounting bolts and lift off the plenum.
  5. Disconnect the fuel lines from the fuel rail and bracket.
  6. Install engine support fixture special tool J 28467-A or an equivalent.
  7. Remove the right side engine mount.
  8. Remove the power steering mounting bolts and support the pump out of the way without disconnecting the power steering lines.
  9. Disconnect the coolant inlet pipe from the outlet housing.
  10. Remove the coolant bypass hose from the water pump and the cylinder head.
  11. Disconnect the upper radiator hose at thermostat housing.
  12. Remove the thermostat housing.
  13. Remove both rocker arm covers.
  14. Remove the lower intake manifold bolts. Make sure the washers on the four center bolts are installed in their original locations.
When removing the valve train components they should be kept in order for installation the original locations.
  1. Remove the rocker arm retaining nuts or bolts and extract the rocker arms and pushrods.
  2. Remove the intake manifold from the engine. Remove and discard the gasket.
  3. Using a suitable scraper, clean gasket material from all mating surfaces. Remove all excess RTV sealant from front and rear ridges of cylinder block
To install:
  1. Place a 0.12 inch (3mm) bead of RTV, on each ridge, where the front and rear of the intake manifold contact the block.
  2. Using a new gasket, place the intake manifold on the engine.
  3. Install the pushrods in their original locations. Coat the pushrods with prelube.
The intake pushrods are marked yellow (5 3 /4 inch long) and the exhaust are green (6 inches long). Make sure the pushrods are properly seated in the valve lifters and rocker arms.
  1. Position the rocker arms in there original locations and tighten to specifications. Refer to the procedure earlier in this section.
  2. Install lower the intake manifold attaching bolts. Apply sealant 12345739 (or equivalent thread locking compound) to the threads of bolts. Tighten the vertical bolts first then the diagonal bolts to 115 inch lbs. (13 Nm).
  3. Install the front rocker arm cover.
  4. Install the thermostat housing.
  5. Connect the upper radiator hose to the thermostat housing.
  6. Fasten the coolant inlet pipe to thermostat housing.
  7. Connect coolant bypass pipe at the water pump and cylinder head.
  8. Install the power steering pump in the mounting bracket.
  9. Loosely install the serpentine belt.
  10. Connect the right side engine mount.
  11. Remove the special engine support tool.
  12. Fasten the fuel lines to fuel rail and bracket.
  13. Install the upper intake manifold and tighten the mounting bolts to 18 ft. lbs. (25 Nm).
  14. Install the MAP sensor.
  15. Connect the upper engine wiring harness connectors to the related components removed earlier.
  16. Connect the vacuum lines to the PCV, vacuum modulator and fuel pressure regulator.
  17. Install the EVAP canister purge solenoid and ignition assembly.
  18. Install the alternator assembly.
  19. Connect the power steering line to the alternator bracket.
  20. Install the serpentine belt.
  21. Connect the spark plug wires to the spark plugs and intake plenum wire retainer.
  22. Install the EGR pipe to the exhaust manifold.
  23. Attach the control cables to the throttle body lever and upper intake plenum mounting bracket.
  24. Install air intake assembly and top half of the air cleaner assembly.
  25. Install the brake vacuum pipe.
  26. Fill the cooling system.
  27. Connect the negative battery cable, then start the vehicle and verify that there are no leaks.

For PARTS REPLACEMENT check in THIS LINK: carpartswholesale.com

Hope helps.

Feb 01, 2011 | 1994 Pontiac Grand Am

1 Answer

Location of thermostat on 2002 olds alero 2.2


Thermostat Removal & Installation 2.2L Engine To Remove:
  1. Remove the exhaust manifold. If equipped with an automatic transmission.
  2. Drain the cooling system.
  3. Remove or disconnect the following: chevy_cav_02-04_tstat.gif

    • Thermostat housing to water pump feed pipe bolts. chevy_cav_02-04_feedpipe.gif

    • Thermostat housing to water pump feed pipe.
    • Thermostat.
To Install:
  1. Install or connect the following:
    • Thermostat.
    • Thermostat housing to water pump feed pipe.
    • Thermostat housing to water pump feed pipe bolt.
      1. Tighten bolt to 89 in lbs (10 Nm).
    • Exhaust manifold if equipped with an automatic transmission.
  2. Fill the cooling system.
2.4L Engine To Remove:
Thermostat assembly 2.4L 87953024.gif

  1. Drain the cooling system.
  2. Remove the exhaust manifold heat shield.
  3. Remove the coolant inlet housing mounting bolts through the exhaust manifold.
  4. Raise and safely support the vehicle.
  5. Remove the coolant inlet housing stud from the oil pan.
  6. Remove wheel and tire assembly.
  7. Remove the engine splash shield.
  8. Remove the mounting bolts from the transaxle-to-engine block support. Remove the support.
  9. Remove the coolant housing pipe.
  10. Remove the thermostat.
  11. Clean the mating surfaces.
To Install:
  1. Install the thermostat.
  2. Install the coolant housing pipe.
  3. Install and secure the transaxle support-to-engine block mounting bolts.
  4. Install the engine splash shield.
  5. Install the wheel and tire assembly.
  6. Install the coolant inlet housing stud to the oil pan.
    • Tighten to 19 ft lb (26 Nm).
  7. Lower the vehicle.
  8. Install the coolant inlet housing bolts through the exhaust manifold.
    • Tighten the coolant inlet housing bolts to 10 ft lb (14 Nm).
  9. Install the exhaust manifold heat shield.
  10. Fill the cooling system.
  11. Inspect the system for leaks.
3.4L Engine To Remove:
  1. Drain the cooling system.
  2. Remove the air cleaner.
  3. Remove exhaust crossover pipe.
  4. Disconnect the surge tank line fitting from the coolant outlet.
  5. Remove the thermostat housing to intake manifold bolts.
  6. Remove the thermostat housing outlet and thermostat.
To Install:
  1. Install the thermostat and housing outlet.
  2. Install the thermostat housing bolts.
    • Tighten the thermostat housing bolts to 18 ft lb (25 Nm).
  3. Install exhaust crossover pipe.
  4. Connect the surge tank line fitting to the coolant outlet.
    • Tighten the fittings to 15 ft lb (21 Nm).
  5. Install the air cleaner.
  6. Fill the cooling system.
  7. Inspect the system for leaks
prev.gif next.gif

Oct 14, 2010 | Oldsmobile Alero Cars & Trucks

2 Answers

Leaking coolant somewhere below after car is warm and shut off can not find,recently replaced water pump, and it is not the radiator


Does this vehicle have a 3.1 or 3.4L motor. If so they commonly have intake manifold gaskets failures. This leads to coolant leaking, usually at the corners of the intake manifold and in some instances leaking into the oil. Look for signs of coolant leaking at the corners of the intake manifold and check the engine oil for coolant.

Sep 05, 2010 | 1997 Chevrolet Monte Carlo

2 Answers

Cylinderhead torque stc.


Cylinder Head Removal & Installation SOHC To Remove:
  1. Relieve fuel system pressure.
  2. Remove timing belt cover. Camshaft timing marks kia-03-20-7032.gif

  3. Turn crankshaft until timing mark on front housing and the arrow "2" on the camshaft pulley align.
  4. Loosen lock bolt on tensioner.
  5. Pry tensioner away from timing belt and tighten lock bolt to relieve tension on the timing belt.
  6. Remove timing belt from camshaft pulley.
  7. Disconnect battery negative cable.
  8. Remove 3 bolts that secure accelerator cable and air intake hose to cylinder head cover.
  9. Detach accelerator cable and place off to side.
  10. Remove the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  11. Disconnect mass air flow sensor electrical connector.
  12. Remove air intake hose.
  13. Remove PCV valve from cylinder head cover.
  14. Remove ISC air hose from idle speed actuator.
  15. Remove air hose from behind intake manifold.
  16. Remove 2 screws from high tension wire protectors.
  17. Detach wire loom from holder at rear of cylinder head cover.
  18. Detach vacuum tube at rear of cylinder head cover.
  19. Remove vacuum pipe. Cylinder Head Cover kia-03-20-7042.gif

  20. Remove 7 cylinder head cover bolts.
  21. Remove cylinder head cover and gasket.
  22. Disconnect 2 ignition coil electrical connectors.
  23. Disconnect 2 fuel injection electrical connectors at rear of cylinder head.
  24. Disconnect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  25. Disconnect heater hose from elbow.
  26. Disconnect brake booster vacuum hose and cruise control vacuum hose from surge tank.
  27. Detach wire harness from rear of cylinder head.
  28. Disconnect purge control solenoid vacuum hose from intake manifold.
  29. Disconnect fuel hose from fuel connector assembly.
  30. Remove grounding bracket.
  31. Remove 4 bolts and intake manifold bracket.
  32. Remove starter.
  33. Detach water bypass hose from bypass pipe.
  34. Disconnect water hoses from oil cooler.
  35. Disconnect fuel hose from fuel pipe.
  36. Remove exhaust manifold heat shield.
  37. Remove exhaust flange nuts and front exhaust bracket bolt.
  38. Lower exhaust system. Cylinder head bolt loosening sequence kia-03-20-7050.gif

  39. Loosen cylinder head bolts in 3 steps in proper sequence.
  40. Remove cylinder head bolts and washers.
  41. Remove cylinder head, intake manifold and exhaust manifold as an assembly.
To Install:
  1. Install NEW cylinder head gasket.
  2. Install cylinder head, intake manifold and exhaust manifold as an assembly.
  3. Tighten cylinder head bolts in 3 steps in reverse sequence that was used during removal. Tighten bolts to 62 ft lb (84 Nm).
  4. Install front exhaust bracket bolt. Tighten bolt to 20 ft lb (27 Nm).
  5. Install NEW lower exhaust flange gasket and 3 nuts. Tighten nuts to 24 ft lb (31 Nm).
  6. Install exhaust manifold heat shield. Tighten nuts to 35 in lb (4 Nm).
  7. Connect fuel hose to pipe.
  8. Connect 2 hoses to oil cooler.
  9. Attach water bypass hose to bypass pipe.
  10. Install starter and bolts. Tighten bolts to 34 ft lb (46 Nm).
  11. Install intake manifolds bracket and 4 bolts. Tighten bolts to 32 ft lb (45 Nm).
  12. Install grounding bracket.
  13. Connect fuel hose to fuel connector assembly.
  14. Connect the following electrical connectors;
    • Oxygen sensor
    • Throttle position sensor
    • Idle speed actuator
    • Oil pressure switch
    • EGR vacuum solenoid valve at intake manifold
  15. Connect purge control solenoid vacuum hose to intake manifold.
  16. Attach wire harness from rear of cylinder head.
  17. Connect brake booster vacuum hose and cruise control vacuum hose to surge tank.
  18. Connect heater hose to elbow.
  19. Connect 2 fuel injection electrical connectors at rear of cylinder head.
  20. Connect 2 ignition coil electrical connectors.
  21. Install cylinder head cover.
  22. Install 7 cylinder head cover bolts. Tighten bolts to 60 in lb (7 Nm).
  23. Install vacuum pipe and 2 bolts at rear of cylinder head cover. Tighten bolts to 60 in lb (7 Nm).
  24. Connect vacuum tube to pipe.
  25. Connect loom holder to rear of cylinder head cover.
  26. Install 2 screws to high tension wire protectors.
  27. Install air hose to behind intake manifold.
  28. Install ISC air hose to idle speed actuator.
  29. Install PCV valve to cylinder head cover.
  30. Install air intake hose.
  31. Connect mass air flow sensor electrical connector.
  32. Install the following;
    • Air hose
    • Air ISC air hose
    • Breather hose
    • Vacuum hose from air intake hose
  33. Attach accelerator cable.
  34. Install 3 bolts that secure accelerator cable and air intake hose to cylinder head cover. Timing belt pulley timing marks kia-03-20-7035.gif

    NOTE: Timing belt pulley timing mark and timing mark must be aligned.
    Camshaft timing marks kia-03-20-7032.gif

    NOTE: The arrow at "2" on camshaft pulley must be aligned with timing mark on front housing.
  35. Install timing belt.
  36. Install timing belt cover.
  37. Pressurize fuel system.
  38. Start engine and check ignition timing.

Jul 11, 2010 | 1999 Kia Sportage

1 Answer

How do you know if you have a blown head gasket


The classic signs to look for are engine over-heating with bluish-grey smoke from the exhaust pipe and it might be smoking excessively, look for coolat present in the engine oil, the engine oil will float on top of the coolant so if the engine oil is reading unusually high on the dip-stick you can loosen the engine oil drain plug just enough until it starts to drip fluid, and if that fluid is water or coolant then you might have a blown head gasket or an intake manifold leak, and if you have all of the symptoms of a head gasket without the smoke from the exhaust pipe it might just be the intake manifold.

Jun 12, 2010 | 1997 Cadillac DeVille

1 Answer

How do I remove the thermostat from a 1995 buick skylark quad 4


remove the exhaust manifold
remove 2- 8mm bolts at coolant pipe flange
now the coolant pipe that runs under the oil pan remove the bolt at the front of the oil pan lower the pipe down
t-stat is in the top of that pipe at the flange

Apr 11, 2010 | 1996 Buick Skylark

3 Answers

1999 mitsubishi montero sport white smoke


the weakest link from water entering engine is intake manifold losing its torque. their are four water ports right next to valve ports. two in front two at rear of intake manifold. they warp fairly easy.so check before re installing

Jan 02, 2010 | 1999 Mitsubishi Montero Sport

Not finding what you are looking for?
1990 Chevrolet Suburban Logo

1,546 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...