Question about 1995 Ford Taurus

1 Answer

Do you know where I could find a diagram of the front drivers side spring and shock assembly -Thank you

Posted by on

  • yadayada
    yadayada May 11, 2010

    What kind of diagram? I would suggest u buy a repair manual.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Www.autozone.com

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Shocks


1992 Toyota Celica is not equipped with front "shocks". This vehicle is equipped with front wheel drive and independent MacPherson strut front suspension. Any repairs made to this system requires the removal of the entire strut assembly, which includes the strut, the coil spring and upper strut bearing assembly.

Replacement of any of the parts of the strut assembly requires the use of specialized equipment designed to compress and hold the coil spring to relieve the tension on the strut and upper bearing assembly.



12_4_2011_9_36_51_pm.gif
Any attempt to disassemble the strut assembly without the proper equipment for compressing and securely holding the coil spring can result in SERIOUS INJURY or DEATH.

Nov 30, 2011 | 1992 Toyota Celica

1 Answer

How do you replace front broken coil spring on 1998 ford windstar? do you have a diagram, pictures or video?


Strut and Spring Assembly Removal
  1. Raise the vehicle on a hoist.
  1. Remove the front wheel and tire assembly.
  1. ani_caut.gif CAUTION: To avoid damage to the 6mm drive hole in the front stabilizer bar link ball stud, do not use an Allen wrench to break loose or tighten to final torque the front stabilizer bar link-to-front shock absorber nut.
    Remove the stabilizer bar link retaining nut and disconnect the link from the strut.


f8740a.gif

  1. ani_caut.gif CAUTION: Do not allow the halfshaft to move outboard. Over extension of the CV joint may result in the separation of internal parts, causing failure of the joint.
    Remove the strut assembly-to-steering knuckle pinch bolt. If required, slightly spread the steering knuckle to ease the removal of the strut. Pry down on the lower control arm and roll the strut base out of the knuckle. Do not pry on the halfshaft, as damage may result. Wire the steering knuckle up to prevent the halfshaft from moving outboard.
  1. Partially lower the vehicle.
  1. Support the strut assembly and remove the top three mount-to-strut tower nuts. Remove the strut assembly from the vehicle.


f9154a.gif

  1. ani_caut.gif CAUTION: The strut assembly is under spring tension. Attempting to disassemble the strut without properly compressing the spring can result in injury.
    Using a suitable spring compressing tool, slightly compress the strut spring to relieve initial tension. Loosen the upper rod nut. Continue to compress the spring until the tension is relieved. Remove the upper rod nut.


f3897c.gif

  1. Remove all upper mounting parts, coil spring, and coil spring isolators from the strut and save them for reassembly. Carefully note the position of each part during removal to ensure proper reassembly. Inspect each part for wear and damage as it is removed.
Installation
  1. ani_caut.gif CAUTION: The bearing and seal assembly is press-fit onto the upper mount. The mount washers must be installed in the correct orientation.
    NOTE: Be sure to check the spring insulator for damage before assembly. If the outer metal splash shield is bent or damaged, it must be carefully bent back, so it does not touch the locator on the bearing and seal assembly.

    NOTE: New gas struts are shipped with the rod in a locked down position. To extend the new strut, remove the external tie down and/or rotate the upper end of the rod, counterclockwise.

    Install the coil spring insulator, coil spring, and upper mounting parts to the new strut assembly. Make sure the spring is correctly seated in both spring seats.


f8737a.gif


Item Part Number Description 1 ? Dust Boot (Part of 18045) 2 N803826-S100 Front Shock Absorber Mounting Bracket Nut
(3 Req'd) 3 N803952-S100 Washer 4 N808625-S100 Front Shock Absorber Nut 5 18183 Front Shock Absorber Mounting Bracket 6 3B455 Front Suspension Bearing and Seal 7 5310 Front Coil Spring 8 5414 Front Spring Insulator 9 18045 Front Shock Absorber A ? Tighten to 35-40 Nm
(25-30 Lb-Ft) B ? Tighten to 55-63 Nm
(40-46 Lb-Ft)
  1. ani_caut.gif CAUTION: Do not over tighten the lock nut; damage to the lock nut or piston rod could result.
    Install new rod lock nut and tighten it to 55-63 Nm (40-46 lb-ft).


f3897c.gif

  1. Remove the spring compressing tool.
  1. Position the strut assembly into the vehicle. Install the three mount-to-strut tower nuts. Tighten the nuts to 35-40 Nm (25-30 lb-ft).


f9154a.gif

  1. Partially raise the hoist.
  1. Position the strut assembly to the steering knuckle. Install the pinch bolt and tighten it to 115-132 Nm (85-97 lb-ft).
  1. Position the stabilizer link to the strut assembly and install the retaining nut. Tighten the nut to 90-100 Nm (66-74 lb-ft).


f8740a.gif

  1. Install the front wheel and tire assembly.
  1. Lower the vehicle.
hope this helps

Aug 14, 2011 | 1998 Ford Windstar

2 Answers

Does this car have shocks front and rear??


Yes but they are called struts on the front and the shock are for the rear . Here is a picture..... Of the front.... mcneb_14.jpg>>>>>>>>>>>>>>>>>>>>..............................................................................................................................................................................................................................................................Here is a picture of the rear............................................................................................... mcneb_15.jpg

Feb 09, 2011 | 2000 Mercury Sable

2 Answers

Are struts on the front or back of this car?


The struts model (MacPherson Strut),are both in front and back of this car.
2000 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Rear, Driver Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly. $72
2000 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Rear, Passenger Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $68
1996 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Front, Driver Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $67
1996 - 2006 Hyundai Elantra Shock Absorber and Strut Assembly - Front, Passenger Side, KYB GR-2/EXCEL-G, Twin tube, Strut Assembly $63
Of course this is only the cartridge, you have to transfer the spring, and the top mount of the existing strut. You need a pair of coil spring compressor to do the job. The basic procedure to replace a strut is:
Remove the top nuts that secure the strut assembly to the frame mount inside the engine compartment. Do not remove the center nut.
Mark the lower strut mounting location on the hub for installation reference. The alignment will be close if the new strut is installed in the same position.
Remove the bolts that hold the strut assembly to the hub.
Remove the strut assembly from the vehicle.
Mark the top mount for installation reference. Using a side mounted spring compressor, compress the spring and remove the top nut and retaining washer. Pull strut assembly out from the bottom of spring.
Slide the new strut assembly up into the spring and reposition the top mount onto the spring in the same position that it was removed. Install the retaining washer and top nut.
Tighten the top nut to the manufacturer's specifications and carefully remove the spring compressor.
Place the strut assembly back into the vehicle.

Oct 16, 2010 | 2000 Hyundai Elantra

1 Answer

91 Audi 100 (non-quattro) needs front shocks replaced


You can pull the shock out from the top but you need special tools. The easiest way for a novice to do it is to pull the strut assembly out of the car, then compress the spring and remove the strut.

Mar 17, 2009 | 1991 Audi 100

1 Answer

'99 Lincoln Conti Front Suspension


yes. try this website they have replacement parts.
Suncore industries dot com

Mar 13, 2009 | 1999 Lincoln Continental

1 Answer

I need to know how to get to the rear suspension (tower)


i don't think you have to do any repairs from the top end. I will list most fromFord shop manual. Please rate as Fixya if this answers your questions. Please report back. Good luck.

Section 04-02: Suspension and Wheel Hubs, Rear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual
REMOVAL AND INSTALLATION Spring Rear
Removal
  1. Position a hoist under the rear axle housing, and raise the vehicle. Refer to Section 00-02 . Place jackstands under frame side rails.
  1. Remove rear stabilizer bar as outlined.
  1. Disconnect the lower studs of the two shock absorbers from the mounting brackets on the rear axle assembly .
  1. Unsnap the RH parking brake rear cable and conduit (2A635) from RH upper arm retainer before lowering the rear axle assembly .
  1. Lower the hoist and axle housing until the rear springs are released.
  1. Remove rear spring and rear spring center mounting insulators (5741) from vehicle.
    -----------------------------------------------------------------
Shock Absorber Removal
Raise the vehicle on a hoist. 1. To assist in removing the upper attachment on shock absorbers using a plastic dust tube, place an open end wrench on the hex stamped into the dust tube's metal cap. For shock absorbers with a steel dust tube, simply grasp the tube to prevent stud rotation when loosening the retaining nut.
  1. Remove the shock absorber retaining nut, washer, and insulator assembly from the stud on the upper side of the frame. Discard nut. Compress the shock absorber to clear the hole in the frame, and remove the inner insulator and washer from the upper retaining stud.
  2. Remove the self-locking retaining nut, and disconnect the shock absorber lower stud from the mounting bracket on the rear axle tube.
  3. Perform Shock Absorber Checks. Refer to Section 04-00 to determine shock absorbers performance.
Installation
  1. Properly prime the new shock absorber . Refer to Section 04-00 , Shock Absorber Checks.
  1. Place the inner washer and rear spring insulator (5536) on the upper retaining stud, and position the shock absorber so that the upper retaining stud enters the hole in the frame. While holding the shock absorber in this position, install a new rear spring insulator , washer and nut assembly on the upper side of the upper frame. Be sure to seat the rear spring insulator in the frame attaching hole. Tighten nut to 34-46 Nm (25-34 lb-ft).
  1. Extend the shock absorber , and place the lower stud in the mounting bracket hole on the rear axle assembly housing. Install a new self-locking retaining nut. Tighten nut to 76.5-103.5 Nm (56-76 lb-ft).
  1. Lower vehicle.
-----------------------------------------------------------------------------
Arm Lower
Removal
Refer to the illustration in Description and Operation. NOTE: To improve rear axle assembly noise and vibration concerns, the rear suspension should be fastened to the frame and rear axle assembly at the curb height position.
NOTE: If one rear suspension lower arm requires replacement, also replace the opposite rear suspension lower arm .
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN REAR SUSPENSION LEVELER COMPRESSOR SWITCH OFF (IF SO EQUIPPED).
NOTE: If both rear suspension arm and bushings and both rear suspension lower arms are to be removed at the same time, remove both rear springs as outlined under Rear Spring Removal. For air spring removal, refer to Section 04-05 .
  1. Mark rear suspension shock absorber relative to protective sleeve with the vehicle in a static, level ground condition.
  1. Remove rear stabilizer bar as outlined.
  1. Raise the vehicle on a hoist, and place jackstands under the rear axle assembly . Refer to Section 00-02 .
  1. Lower the hoist until the shock absorbers are fully extended to relieve rear spring pressure.
  1. Support rear axle assembly under differential pinion nose as well as under rear axle assembly .
  1. Remove and discard the lower arm pivot bolt and nut from the axle bracket. Then, disengage the rear suspension lower arm from the bracket.
  1. Remove and discard the pivot bolt and nut from the frame bracket, and remove the rear suspension lower arm .
-----------------------------------------------------------------
Upper
Removal
SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Suspension Bushing Service Set T79P-5638-A1, A2 and A5 Rear Axle Control Arm Bushing Tools T86P-5638-AH
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
  1. Raise the vehicle, and support the frame side rails with jackstands. Refer to Section 00-02 .
  2. Support the rear axle assembly .
  3. Lower the rear axle assembly , and support the rear axle assembly under differential pinion nose as well as under rear axle assembly .
  4. Unsnap parking brake rear cable and conduit from upper arm retainer.
  5. Remove and discard the nut and bolt retaining the rear suspension arm and bushing to the rear axle assembly housing. Disconnect the rear suspension arm and bushing from the housing.
  6. Remove and discard the nut and bolt that secures the rear suspension arm and bushing to the frame bracket, and remove the rear suspension arm and bushing . If upper arm rear bushing is to be replaced, use Suspension Bushing Service Set T79P-5638-A and Rear Axle Control Arm Bushing Tools T86P-5638-AH and the following procedure:
  7. Place the upper arm rear bushing remover tool in position, and pull bushing out. Using Suspension Bushing Service Set T79P-5638-A install bushing assembly into bushing ear of rear axle assembly.
------------------------------------------------
Stabilizer Bar
sra~us~en~file=ani_caut.gif~gen~ref.gif WARNING: TURN OFF REAR SUSPENSION LEVELER COMPRESSOR SWITCH (IF SO EQUIPPED).
Removal
  1. Raise vehicle on hoist, and place jackstands under the frame side rails. Refer to Section 00-02 .
  1. Lower the hoist and rear axle assembly housing until the shock absorbers are fully extended.
  1. Disconnect rear stabilizer bars from rear stabilizer bar link and bushing (5C488) . Remove bolts and stabilizer bar bracket (5486) retaining rear stabilizer bar to rear axle assembly .

Mar 05, 2009 | 1994 Lincoln Town Car

1 Answer

I need to change front shocks on a '04 Ford 150 4wd.Whats the procedure and tools i would need.Thank you


You Must Put it UP On Jack Stands And Take Out the LOWER BOLT From Shock FIRST ,Drop Lower Control arm By Removeing Lower Ball Joint AND OUTER TIE ROD.There are are 3 Nuts On top where the Coil Spring Seats Remove Them, Remove Assembly The Same as A STRUT ASSEMBLY, YOU Must USE CAUTION Use Spring Compresion tool to Remove top Shock Nut. REVERSE PROCEDURE For Instalation. Hope this Helps ;;;;;;;;AS FOR TOOLS METRIC SET & THE ONLY 'SPECIAL TOOL" IS >> A COIL SPRING COMPRESSOR. BUT NOTHING ELSE OTHER THAN METRIC WRENCHES & SOCKETS

Jan 29, 2009 | 2004 Ford F350

1 Answer

Front spring and shock assembly diagram


d4f5461.gif
Item Part Number Description 1 5310 Front Coil Spring 2 18124 Front Shock Absorber 3 3A130 Tie Rod End 4 1104 Wheel Hub 5 3K185 Front Wheel Knuckle 6 3078 Front Suspension Lower Arm 7 5482 Front Stabilizer Bar 8 5K484 Stabilizer Bar Link 9 N806899-S60 Bolt (4 Req'd) 10 5486 Stabilizer Bar Bracket 11 5484 Rack and Pinion Mounting Bracket Insulator (2 Req'd) (Position Slits Toward Front of Vehicle) 12 W520214-S60 Nut (2 Req'd) 13 N807144-S60 Nut (2 Req'd) 14 N803990-S60 Bolt (2 Req'd) 15 N806364-S60 Nut (2 Req'd) 16 N808466-S428 Nut (2 Req'd) 17 N808391-S100 Bolt (2 Req'd) 18 N807089-S101 Nut (2 Req'd) 19 W500746-S426 Bolt (2 Req'd) 20 W520214-S60 Nut (2 Req'd) 21 N804608-S1428 Nut (2 Req'd) 22 N804002-S100 Washer (2 Req'd) (Dished Side Up) 23 18183 Front Shock Absorber Mounting Bracket (2 Req'd) 24 3B455 Front Suspension Bearing and Seal (2 Req'd) 25 N811008-S100 Washer (2 Req'd)(Dished Side Up) 26 N803766-S60 Nut (6 Req'd) A — Install With Color Code at Bottom of Link — Green—RH Side, Red—LH Side B — Tighten to 30-40 Nm (22-29 Lb-Ft) C — Notches and Stamped "Front" Toward Front Of Vehicle D — Tighten to 47-63 Nm (35-46 Lb-Ft) E — Tighten to 77-103 Nm (57-75 Lb-Ft) F — Tighten to 98-132 Nm (72-97 Lb-Ft) G — Tighten to 68-92 Nm (50-67 Lb-Ft) H — Tighten to 53-72 Nm (39-53 Lb-Ft)

Dec 30, 2008 | 1995 Ford Taurus

1 Answer

Replace front shock absorbers


My answer is not going to help you because not only do you need specialized equipment, but you will need special experience to perform this job.

You would be required to completely remove the entire front strut assembly from the car. It has to be safety set up on jacks. Once you have the strut assembly out of the car, special spring clamps are needed to compress the heavy spring that is part of the strut. These require very special clamps that compress the springs. If this is not done right, it can conceivably kill a person.

Once the spring has been removed, the strut it self must be removed from the strut housing using an impact wrench.

Once both sides are changed, the car must be realigned in the front end, otherwise the car will not steer or track properly.

Over all, this is a major job. These are not shock absorbers, as you would know them, but are called McPherson struts.


If you would like to contact me again about this or other problems, feel free to do so.
Bill
ASE Master Technician

Nov 25, 2008 | 1993 Toyota Corolla

Not finding what you are looking for?
1995 Ford Taurus Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

60792 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...