Question about 1992 Dodge Dynasty

1 Answer

My engine light comes on and my car will not stay cranked

I have a 1992 Dodge Dynasty and the engine light comes on . It will crank, but when I get off the gas it cuts off.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 18 Answers

You need to take it to your nearest auto zone and let them run a test on your engine light its free and they should be able to tell you what it is reading

Posted on Dec 30, 2008

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1992 Dodge dynasty turn signal lights and brake lights aren't working can u help


It's probably a bad turn signal switch, since the brake lights are wired in with the turn switch.
If you have a 3rd brake light, the high mounted one in the rear window, this light is separate from the brake lights that go through the turn switch. If your high mount brake light comes on, when brakes are pressed, then brake switch is good and probably a bad turn signal switch. Of course if you have a voltmeter or test light, you could test for power in and power out from the turn switch connector, to help you find the problem.

Oct 23, 2016 | 1992 Dodge Dynasty

1 Answer

Ignition switch on dodge dynasty?


I had a similar problem years ago. As long as your dash lights come on, it's likely you can use an external pushbutton switch to run the starter. There are likely just 4 wires on the ignition switch. Power from the battery, and switched to:
accessories
main car stuff (dash lights, ignition, signals, etc)
starter.
splice in wires from battery and starter to new switch, and you're good to go. This worked for years on my old car.

Jun 01, 2015 | 1992 Dodge Dynasty

2 Answers

No maintenance done in 3 years. Car starts but does not remain running fuel filter or plugs or both?


do a computer self test.

Insert key into ignition. turn as follows;

off-on, off-on, off-on. " on " is when the dash lights come on and "off" is one click back from on.

Codes with flash out on the check engine light is pairs of numbers; 5-5 being the end of the test.

Google your findings; eg, "1991 dodge dynasty code 22"

Your condition is usually a sign of a bad crank or cam position sensor ( if you cant keep the engine running by pressing on the gas pedal.)

If you can keep the car running by pressing the gas pedal than your problem is the idle control valve or a broken vacuum hose.

autozone.com has a tutorial on these parts.

Aug 19, 2011 | 1991 Dodge Dynasty

1 Answer

I have a 1992 Dodge Dynasty. I just bought it from a one owner seller. It has been well taken care of. recently the Check Guages light has been coming on. The first time it came on about a month ago, the...


The only time that message comes on is because one of you guages
quit working temporally, fuel guage sounds possible, because you lost fuel
pressure at the same time, all feed by same harness, with 4 wires in it, 2 for guage,
2 for fuel pump. connector is at rear of tank, than into frame area, check and follow
harness back to front of vehicle. possible corrision,

Good Luck, RDJRP.

Apr 12, 2011 | 1992 Dodge Dynasty

1 Answer

1992 dodge dynasty cuts out when i give it gas. runs fine for a few minutes and idles fine


I would start by checking the catalitc converter when these clogg the moter cant push out enough air for it to climb rpms but it will run fin at low rpms... Also as they heat up the metal expands closeing them off even more.

Oct 20, 2010 | 1992 Dodge Dynasty

1 Answer

ACblower working great except made a little raquet sometimes but would usually quite.Cut car off when returned to crank car again no air though vents.Compressor still kicking on like should.Fan just gave...


It ispossible that the filter is choked and the blower fan is choked. Occasionally the fan is getting struck with the dirt.
So you might have to remvoe the dash and access the blower fan , clean the filter and the cooling pipes to get your AC more efficient and less noisier.
The filter cleaning must be done occasionally, specially if you are driving with windows down as ddirt will accumulate into the filter.
so check this out.
Credit if this advice is helpful

Aug 26, 2010 | 1992 Dodge Dynasty

1 Answer

My 1992 dodge dynasty runs really rough and wont Idle at all.


Usually this is a sign of a malfunctioing coolant sensor. It is close to the thermostat housing. Dis connect wire to the sensor when engine is warm & if the engine runs normally change the sensor. You may lose a little coolant so have other one ready to put in as quickly as possible. Top off coolant if nesessary. This is a common problem with Chrysler products. Do not over tighten sensor, 5ft. lbs. Good luck!

Dec 30, 2009 | 1992 Dodge Dynasty

3 Answers

Serpentine belt diagram for a 3,3l dodge dynasty with ac


For the 1991 DODGE DYNASTY - V6 3.3L 201ci GAS FI N R , review this informacion:

Belt Routing Diagram
- Multiple Accessory, w/o A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. After 2/27/91)
- Multiple Accessory, w/o A.C. (Mfg. Before 2/27/91)
- Multiple Accessory, w/A.C. (Mfg. Before 2/27/91)
684ce70.jpg


Remove the serpentine belt by using a breakover bar, rachet or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the belt.

Hope helped with this (remember rated this help) Good luck.

Nov 12, 2009 | 1991 Dodge Dynasty

Not finding what you are looking for?
1992 Dodge Dynasty Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...