Question about 1998 Toyota RAV4

1 Answer

Where is the tach wire in 1998 toyota rav 4?

Hi, i'm installing an remote starter on my 98 rav 4. and i was wondering, does anyone know where the tach wire is at? and i read the booklet and it say its at the ignition coil and i can't find it? i don't know what it look like, so can anyone send me a picture of it or describe where it is at with detail, thanks...

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Toyota Master
  • 1,861 Answers

You are not going to find the Tach wire in the engine compartment, because the tach signal comes out of ther vehicle's ECU.

The Tach wire is solid BLACK, located on pin 13 on the ECU.

Posted on Dec 30, 2008

  • Toyota Ed Dec 30, 2008

    I would really appreciate a FIxYa rating for my info. Thanks.

×

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can I get the installation wiring diagram for remote starter viper where can this be found


1998 Cherokee?
wow , old bendix starters ,they are long long gone, (done many)
a blast from the past. LOL
so is this an after market hacked in Remote?>
sure.
well buy a new system and read the instructions.
if using an old system , get the instructions online, at makers web site, we can not guess makers, of anything aftermarket.

it hangs up the starter solenoid, , and is very dangerous to you , like that. sure.
my guess is the control (in car) is bad, shorted relay in box or transistor that drives the small wire to the starter, or to cars starter relay .

the starter relay is in the USA PDC fuse box.
all answers USA , not export jeeps, this is a USA forum (calif)

Feb 08, 2015 | 1998 Jeep Cherokee

1 Answer

CAN ENGINE IN 98 RAV 4 BE REMOVED OUT THE TOP?


top- buy removing the 4 motor/ tranny mounts
bottom - buy droping it with the sub frame.
either way you need to remove the shift linkige. (and wiring)

Apr 02, 2013 | 1998 Toyota RAV4

1 Answer

How do I remove the dash on my 1997 Rav 4 so I can get at the radio


This Toyota Rav-4 1998 to 2000 - Radio Installation / Stereo Installation coudl helped: InstallDocs/Toyota/PDF/869029.pdf

Good luck.

Jun 03, 2011 | 2003 Toyota Camry

1 Answer

1998 toyota rav 4. Right side low beam headlight doesn't work. Hi beam on that side does. Checked fuses, they appear OK, and tried 2 other headlights. Left side hi and low working fine.


sounds like there is a broken wire. the only advise i can give you is to follow the hot wire for that light untill you find the break in the wire.

Dec 25, 2009 | 1998 Toyota RAV4

1 Answer

98 CRV LX AWD - - - Install a Remote Key Fob


the easiest way to add remote entry is to get an alarm system or remote car starter off of ebay. you have to be pretty good at wiring to install them but they do come with directions. you will need the wireing diagrams of your car also. if you are not very confident in wiring you can have them installed for one or two hundred dollars at a sterio shop.

Jun 26, 2009 | 1998 Honda CR-V

3 Answers

1998 rav 4 ecu pinout location


sorry never done one so i havent a clue,in the good old days the tach connected to the coil wire but now with all this fancy electrics ,Well what happens is they call it vehicle security so they dont have to release the diagrams and this is done to stop people like myself from by passing the immobilisers when we service a vehicle.Because no doubt as you are aware on new cars that if you drop the oil the immobiliser cuts in.Change the battery and the same thing happens.So what happens to keep the dealers in work ,yes you have guessed it no wiring diagrams ,multilayered circuit boards and wires all the same colour to stop people like me from soldering the two outside legs together of a big switching transistor together to make the vehicle general mechanic friendly.Also encrypted software is used to stop the fault codes from being read ,they throw up the wrong code ?? try asking dealer to install then post where he connected too .,best of british with it

Mar 03, 2009 | 1998 Toyota RAV4

1 Answer

2004 toyota corolla tach wire


you can also solder the wire to the tach wire, this way it won't come off and cause a malfunction

Jul 03, 2008 | 2004 Toyota Corolla

Not finding what you are looking for?
1998 Toyota RAV4 Logo

Related Topics:

380 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...