Question about 2001 Hyundai XG300

1 Answer

Difficulty with replacing fog lamp bulb on 2001 Hyundai XG300

I cannot figure out how to replace the fog lamp bulb (front passenger side). Need some guidance or steps on how to replace.

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 3 Answers

Remove the headlight and put it in from the top.

Posted on Dec 31, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Headlight come on , replace dimmer bulb but light comes on and goes back out. could it be relay or switch itself. The light and fog light work on driver side but not passenger side. IThis problem occur...


it sounds as though there is a loose connection on the passenger side. Check socket and switch bulbs from driver and passenger side. hope this helps tim

Sep 05, 2010 | 2001 Hyundai XG300

1 Answer

I need to replace a foglamp bulb right side.I have fairly easy access to & can see the rubber housing for the bulb,but cannot figure out how to remove it.Do I need to rermove the entire assembly in...


Typically the fog lamp is located in the front bumper assembly. It's usually fairly easy to access and replace these.

Place the car is park, secure parking brake. Use a creeper to scoot under the front end of the car, look up into the bumper. Located the backside of the fog lamp holder. You would usually grab and twist counter clockwise about an inch, then pull straight out. Push in on the bulb while turning counter clockwise until it pulls out of the lamp holder.

These fog lamps usually have a little bit of cushioning grease in the socket. Do not remove the grease or connectivity problems will result with the new fog lamp. Push the new bulb in, turn clockwise until bulb stops turning, release hand pressure.

Installation is the reverse of removal.

May 25, 2010 | 1999 Oldsmobile Eighty Eight

1 Answer

Fog lamp replacement on 2008 elantra


1. Disconnect the negative (-) battery terminal. 2. Remove the front side cover screw. 3. Remove the front fog lamp assembly connector (A).

38eda8f.gif 4. Remove the front fog lamp bulb (A).

20279ba.gif

Jun 20, 2009 | 2008 Hyundai Elantra

1 Answer

Replacing 2001 Hyundai XG300 headlight, how difficult?


1bd6158.jpg Here's a photo - remove cap, disconnect connector to bulb, move bulb retainer out of the way & extract bulb - installation of new bulb is in reverse order.
If you want to replace the entire ASSEMBLY, there are three (3) 10mm bolts holding the assy. Remove them, then slide assy forward to access connectors - disconnect them.



06bdfd0.jpg

Jun 20, 2009 | 2001 Hyundai XG300

1 Answer

How change headlight on hyundai 2001 xg300


Remove the head lamp and disconnect the head lamp connector. 0f7fe9f.jpg Remove three 10mm bolts Unscrew the headlamp bulb CAPS to access bulbs. 5502d76.jpg

Jun 13, 2009 | 2001 Hyundai XG300

1 Answer

How to replace fog light bulb on 2001 hyundai 300xg


Replaced from the back side. Two ways to do this. 1. move the wheel well liner partially out of the way to get to the bulb & connector.
2. Remove the headlamp assy above the fog lamp bulb you wish to replace (pass side is easier than the driver's side because of the engine intake ducting on that side)
b6ca2de.jpg ad1a4b8.jpg .

Mar 19, 2009 | 2001 Hyundai XG300

2 Answers

2001 Hyundai XG300 Fuse Diagram


Here is the fuse arrangement...you can see there are usually some spares if they are there.
06fe106.gif

49834c0.gif

This should answer your question.
If it helps please rate my answers.
You can do it.
Brett

Mar 19, 2009 | 2001 Hyundai XG300

1 Answer

Tail lamp replacement


if there aren't screws on the out side lens, open trunk to get access.

Nov 30, 2008 | 2001 Hyundai XG300

1 Answer

2007 Hyundai Santa Fe - Replacing fog light


hi have not had pleasure of this on santa fe yet? but will try to help dependant of which side o/s or n/s ? i would first remove the screws holding the front of the under engine plastic cover/shield and drop down sufficient to gain view/access? to the rear of fog lamp then if a cover is on? try turning anti clock to remove? or if rubber cover pull off? then the bulb and clip should be visible? unplug the wire from bulb then the spring clip holding bulb in place normally just sring the 2x top ends together and swing down/clear to remove bulb? refit new bulb correctly! pay attention to position old bulb positioned? then clip securely and re connect wire at this stage it would be best to ensure bulb works ?? before you re assemble all else? wish you luck and hope this helps with your problem ?

Oct 28, 2008 | 2007 Hyundai Santa Fe Limited

2 Answers

Changing fog light bulb


I just replaced the fog light bulb on my 2008 Azera. I went under the car and removed two screws from the protective shield. I pulled down the shield and reached up and turned the fog light socket and pulled it out of the housing, remembering which side the wires were on and removed the old bulb (Don't touch the new bulb with your hand) and replaced it with the new bulb. The job took less then 15 minutes

Aug 08, 2008 | 2002 Hyundai Santa Fe

Not finding what you are looking for?
2001 Hyundai XG300 Logo

Related Topics:

264 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

60960 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...