Question about 2001 Lexus RX 300

1 Answer

Running lights How do you replace light bulb on the passenger side rear 1/4 panel bumper area

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 17 Answers

Remove 3 - 4 screws on fender cover close to side marker light. Pull fender cover out a bit for you to use your other hand to reach side marker light. By twisting on one direction and here you go the light out. Replace new bulb and replace everything on reverse order.

Posted on Aug 23, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Weird tail light problem


HI Matt,
Your issue sounds like a fault, most likely in the rear lights. Current is feeding from the brake light circuit, into the running light circuit. The most common causes are a bulb filament broken and touching the running light circuit, and loss of ground.
observe the rear lights closely and you should get a clue as to which light is failing....but if not, just pick one....
I would run a temporary ground and test again, if no results, pull the brake light bulbs...
Transient current is often difficult to wrap your mind around, until you understand what can happen.
Doc

Mar 08, 2012 | 2006 Jeep Grand Cherokee

1 Answer

Have a 1986 chey k 10 truck. having problems with running tail light. i changed all the light bulbs. brake and blinker lights work but no running tail lights.


you may have bad sockets for the tail light circuit or a wiring problem under the rear of the truck along the bumper and drivers side frame area as this area takes a beating causing the wires to wear through rubbing and braking.also check the fuses as it could be just a fuse.

Mar 17, 2011 | Chevrolet 1500 Cars & Trucks

2 Answers

My rear marker/ running lights are out and i need to know how to get to them


Signal and Marker Lights Removal & Installation To Remove:
  1. Remove or disconnect the following:
    • Screw from the side marker lamp.
    • Side marker lamp from the front and/or rear bumper fascia.
    • Bulb/socket from the side marker lamp.
    • Bulb from the socket.
To Install:
  1. Install or connect the following:
    • Bulb to the socket.
    • Bulb/socket to the side marker lamp.
    • Side marker lamp to the front and/or rear bumper fascia.
    • Screw to the side marker lamp. Tighten to 2 N.m (18 lb in ).
prev.gif next.gif

Jan 08, 2011 | 2002 Pontiac Sunfire

1 Answer

2001 Acura TL - Replacing driver side headlight. Does bumper really need to be removed ? OR, can the air intake sleeve come out to access the bulb cover from the rear


You shouldn't have to remove the bumper. Feel behind the light on the engine side and you should find a collar assembly with wires running into it. If you twist that collar off and then pull back toward the rear of the vehicle, pull the collar back not the wires, the light bulb should come out of the light assembly. From there it is just a matter of unplugging the old bulb and putting the new one back in them putting everything back. The whole job should take about 15 minutes.

Nov 11, 2010 | 2001 Acura 3.2TL

1 Answer

O replace passenger side rear turn signal bulb on 2004 Cadillac


open trunk, remove the plastic panel around the latch plate, remove the plastic mounting bolts that hold the grey trunk liners in place, there are two 10mm nuts that hold in the light remove nuts pull out light twist the bulb retainer out and replace bulb.

Jul 12, 2010 | 2004 Cadillac CTS

1 Answer

How do you replace the rear liscense plate lights


Look behind you bumper where the lights are installed. There should be a clip slipped over the back of the housing that holds the light into the bumper. 1 per light. Use some needlenose plyers or a screwdriver to push it off. The light sould pull out of the bumper from the other side. You can disconnect the harness is you wish or just replace the bulb. Whichever suits your fancy. After replacement put the holder back into the bumper and slip the clip back on behind it. 10 minute job.

Apr 06, 2010 | 1998 Ford Explorer

2 Answers

Driver side blinker won't blink


replace the drivers front bulb. There are 2 different elements in the bulb 1 for park lights 1 for directional

May 25, 2009 | 2005 Buick Rendezvous

4 Answers

Front driver side turn signal light doesn't flash.replaced bulb,replaced socket,all other lights work on emergency flasher,except front driver side.rear driver side turn signal light works,but flashes...


replace flasher......usually located in fuse block area...listen in this area....select passenger side ...then select driver side...you can hear flasher clicking...you have seperate flashers for each...FLASHERS are small cubes plugged into fuse block....probable bad driverside flasher

May 09, 2009 | 1998 Buick Century

1 Answer

Rear lights


Sounds like a water leaking issue. Try taking out the whole light panel, drying it and spraying it with DW 40. worked for me

Nov 11, 2008 | 2001 Volkswagen Golf

1 Answer

SIDE MARKER LIGHT, PASSENGER SIDE


Assuming you are talking about the side marker bulb in the bumper, you need to get behind the bumper and un bolt the lens from the back side to change lens or if just bulb replacement twist socket counterclockwise to remove from lens and then change bulb. Keep in mind if the bumper has been hit this will be very difficult to do unless you loosen up bumper and pull out.

Jul 17, 2008 | 2003 Nissan Xterra

Not finding what you are looking for?
2001 Lexus RX 300 Logo

324 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...