Car will not lock by remote control

This is not a good thing. Ford uses a computer called the GEM and that means General Electronics Module. It controls:

• Low Coolant Indicator On Cluster
• Brake Indicator on Cluster
• DRL - Control
• Wipers
• AutoLamps
• Rear Defrost
• Interior Lamps(dome)
• High Beam Indicator only (cluster)
• Low Coolant indicator
• Key-in Buzzer
• Seatbelt indicator only (Cluster)
• Trunk Pop Relay
• Power Locks
• Door Ajar Sensors
• Door Keyless entry pad
• Remote Keyless Entry
• One Touch Down (power window)
• Air Bag Tone
• Anti Theft (perimeter Alarm) (SEL, or SE(s) with mods)
• Lift gate ajar (wagon)
• Liftgate Pop
• Accessory Delay signal (accessory that work after engine off, prior to door ajar)
• Battery Saver Relay signal (accessory that work after engine off, 15 mins) Map lights, vanity mirrors

They are located behind the radio in the dash and they are $$$ about 600 USD.

my suzuki alto 2009 locks keeplocking on and off all the time can you help with problem

Programming
When
Remote control added or replaced. System malfunction.
How
Obtain all remote controls. A maximum of 3 remote controls can be programmed. Switch ignition ON. Repeat procedure below 3 times: Within 4 seconds: Press lock or unlock button. Within 4 seconds: Switch ignition OFF. Within 4 seconds: Switch ignition ON. Within 4 seconds: Press lock or unlock button. System should now lock or unlock vehicle. Within 4 seconds: Press lock or unlock button. Within 10 seconds: Press lock or unlock button of first remote control. System should now lock or unlock vehicle. Press lock or unlock button of second remote control. System should now lock or unlock vehicle. Press lock or unlock button of third remote control. System should now lock or unlock vehicle. Switch ignition OFF. Remove key. Check operation of all programmed remote controls.
IMMOBILIZER CAN ONLY BE SET BY DIAGNOSTIC EQUIPMENT

Programming
When
Remote control added or replaced. System malfunction.
How
Switch ignition ON. Press and hold lock button Fig. 1 [2] for approximately 10 seconds. Keeping lock button depressed, press and hold unlock button within 10 seconds. Programming mode activated (acoustic signal will be heard). Proceed as follows: Release lock/unlock button. Complete the following within 30 seconds: Press lock or unlock button of first remote control. Correct programming indicated by a single acoustic signal. Press lock or unlock button of second remote control. Correct programming indicated by a single acoustic signal. Repeat above procedure to program any remaining remote controls. Remote controls can also be programmed using diagnostic equipment.
NOTE: A maximum of 4 remote controls can be programmed.

turn key all the way on (not to start) let set for 1 hur cycle key and try it.

I used to install power locks on cars. Lets see if I can help...

Take off your door panel, find the small rod that is connected to the door lock itself (the part that actually shows if the door is locked or not) There should be an actuator of some sort connected to the small rod that pushes back and forth when you hit the lock button. This may have popped off or is loose/bent...

Or, There may be module inside the door that controls your locks either way, pop off your door panel and see what you got!

Either the wring going to that motor or the motor itself is bad.

suzuki swift central locking does not operate when using remote key fob

you are going to have to replace the lock buttom actuator motor.

I will do it in my own way since the wiring is messed up, and when i press close on my Remote, the trunk pops open. I will Harness this problem to benefit me since my remote does not have a trunklid switch. I will route the Motor (that has a piston) wire through the switch relay (located just above the vehicle ID plate area), so that opening the trunk lid is only possible when i keep pressing the trunk open swich (on the trunk lid) while at the same time pressing the close/LOCk button on my remote.