Question about 2008 Dodge Durango

1 Answer

Time will not show

2008 Dodge Durango - up until yesterday the time would show on the display. now when you push the time button it says "clock not available"

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 2 Answers

This is also answered under the "clock not available" thread. I took the truck back for warranty work and this was the dealer's explanation: This is a known, but rare, glitch in the radio. It is not widespread enough for Dodge to issue a bulletin, but there is a write-up in the system that Dodge technicians access that covers this. The "repair" is to disconnect the battery for 5 minutes and/or remove the IOD (Ignition Off Draw fuse(s)). The radio then "resets" itself. If the problem persists, they have to replace a component of the radio system.

Posted on Mar 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to set the clock on a 2008 chevy cobalt


Setting the Clock (H-clock symbol, O-pwr symbol, f-music note symbol)
Without Date Display
AM/FM Base Radio with a Single CD Player
This type of radio has a
H
button for setting the time.
You can set the time by following these steps:
1. Turn the ignition key to ACC/ACCESSORY or
ON/RUN. Press the
O
knob, located in the
center of the radio, to turn the radio on.
2. Press the
H
button until the hour begins flashing
on the display. Press the button a second time and
the minute begins flashing on the display.
3. While either the hour or the minute numbers are
flashing, turn the
f
knob, located on the upper
right side of the radio, clockwise or counterclockwise
to increase or decrease the time.
4. Press the
H
button again until the clock display
stops flashing to set the currently displayed time;
otherwise, the flashing stops after five seconds and
the current time displayed is automatically set.
To change the time default setting from 12 hour to
24 hour, press the
H
button and then the pushbutton
located under the forward arrow label. Once the
time 12H and 24H are displayed, press the pushbutton
located under the desired option to select the default.
Press the
H
button again to apply the selected default,
or let the screen time out

Dec 27, 2014 | 2008 Chevrolet Cobalt

1 Answer

How do i change the clock on a 06 Nissan Lafesta, manual is in japanes


Hope this helps
If you are talking about the clock on the DVD display then.....

Audio display model
1. Turn the audio unit on by pushing the "PWR"
button.
2. Push the "MENU" button until the display
indicates the clock adjustment mode.
If the "CLOCK OFF" is indicated on the display,
push the "TUNE" button to change the mode
to "CLOCK ON". Then push the "MENU" button
The time indicator will flash.
3. Push the "SEEK TRACK" button to adjust
the hour.
Push the "TUNE" button to adjust the
minute.
Pushing the , buttons will advance
and , buttons will turn back
the time.
4. Push the "MENU" button to finish the
adjustment.

May 24, 2014 | Cars & Trucks

1 Answer

2002 dodge stratus clock setting


I'm pretty sure the 02 is the same as the 01, heres how I set that one, There are two rubber buttons next to the clock/radio display. Just push those in with a pen or needle until you have the time where you want it.On the right front of the radio display, there are two buttons, the one at the top marked with an "H" for hours and one beneath it marked with an "M" for minutes.



Sep 27, 2011 | 2002 Dodge Stratus

1 Answer

I don't know how to set my clock on my 2006 uplander


Hello, here is the instructions for setting your clock on this vehicle.


Press the H or the M button to enter the clock mode. Press and hold H until the correct hour appears on the display. Press and hold M until the correct minute appears on the display.
To change the time default setting from 12 hour to 24 hour, press either the H or the M button to enter the clock mode. Press the tune knob to select between the 12 or 24 hour display format. The clock mode automatically times out with the changed display format set as the current default setting.

Dec 09, 2010 | 2008 Chevrolet Uplander

1 Answer

How do I reset the clock on a 2008 Impala, and 2008 Accord? I can't find the manuals


For the Impala:

AM/FM Base Radio with a Single CD Player
This type of radio has a H (clock) button for setting the
time. You can set the time by following these steps:
1. Press the H button until the hour begins flashing on
display. Press this button a second time and the
minutes begin flashing on display.
2. While either the hour or the minutes are flashing,
turn the f (tune) knob, located on the upper right
side of the radio, clockwise or counterclockwise
to increase or decrease the time. Instead of using
the tune knob, you can also press the SEEK arrows,
\FWD (forward), orsREV (reverse) buttons
to adjust the time.
3. Press the H button again until the clock display
stops flashing to set the currently displayed time;
otherwise, the flashing stops after five seconds and
the current time displayed is automatically set.
To change the time default setting from 12 hour
to 24 hour, press the H button and then the
pushbutton located under the forward arrow label.
Once the times 12H and 24H are displayed, press the
pushbutton located under the desired option to
select the default. Press the H button again to apply
the selected default, or let the screen time out.
With Date Display
Single CD (MP3) Player
This type of radio has a H (clock) button for setting the
time and date.
To set the time and date, follow these instructions:
1. Turn the radio on.
2. Press theHbutton and the HR, MIN, MM, DD,
YYYY (hour, minute, month, day, and year) displays.
3. Press the pushbutton located under any one of the
labels that you want to change. Every time the
pushbutton is pressed again, the time or the date if
selected, increases by one.
• Another way to increase the time or date, is to
press the right SEEK arrow or\FWD button.
• To decrease, press the left SEEK arrow or
sREV button. You can also turn the f (tune)
knob, located on the upper right side of the radio,
to adjust the selected setting.

The date does not automatically display. To see the
date press the H (clock) button while the radio is
on. The date with display times out after a few seconds
and goes back to the normal radio and time display.

Mar 15, 2010 | 2008 Chevrolet Impala

1 Answer

Cant figure out how to set the minuetes on the clock


1. Turn the ignition key to the on position.
2. Press the time button until the hour starts to flash.
3. Turn the tune dial until the hour is set.
4. Press the tune button this will make the minutes flash
5. Turn the tune dial until the minutes are correct.

Feb 16, 2010 | 2004 Dodge Durango

1 Answer

Need to set clock on 2008 Dodge Avenger


push and hold set up until number blinks to switch to mins push tune knob

Jul 24, 2009 | 2008 Dodge Avenger

1 Answer

2007 dodge durango


Clock Setting Procedure
1. Press and hold the time button until the hours blink.
2. Adjust the hours by turning the right side Tune /
Audio control.
3. After the hours are adjusted, press the right side Tune /
Audio control to set the minutes.
4. Adjust the minutes using the right side Tune / Audio
control.

Owner's Manual under: INSTRUMENT PANEL AND CONTROLS 195


If this works please give me a rating on my solution, thanks!

OpenSource13


http://www.fixya.com/PostAnswer.aspx?thid=2028796&prdid=696996 where to find your Owner's Manual
4

Apr 19, 2009 | 2005 Dodge Durango

2 Answers

Clock not available


I took the truck back for warranty work and this was the dealer's explanation: This is a known, but rare, glitch in the radio. It is not widespread enough for Dodge to issue a bulletin, but there is a write-up in the computer system that Dodge technicians access that covers this. The "repair" is to disconnect the battery for 5 minutes and/or remove the IOD (Ignition Off Draw fuse(s)). The radio then "resets" itself. If the problem persists, they have to replace a component of the radio system.

Jan 06, 2009 | 2008 Dodge Durango

1 Answer

Clock reset


press the set button
push the volume button in, it's going to either show a P or an A
press the set button again
push the volume button (it's going to let u change the hour)
use the tune button to change the numbers (turn it left or right until u get to the number u want)
press set button
u're now able to change the minutes
use the tune button to change the numbers (turn it left or right until u get to the number u want)
press set again
u're now home free and now how to set the clock anytime u wish :) :) :)
hope this helps...i also have a 1988 dodge aries
have a great day.

Oct 30, 2008 | 1988 Dodge Aries

Not finding what you are looking for?
Cars & Trucks Logo

325 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...