Question about Lexus SC 400

1 Answer

Can't remove the leather cover off the gearshift

I am having difficulty removing the leather cover off the gearshift of my '96 SC400. There is a control/button for overdrive on the shift that I think is the culprit, but it is not coming off easily. Please help!

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Take the plastic cover down there are two screws take them out pull shifter handle off you should be able to fix it like that

Posted on Jan 09, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i take the radio out of my 96 xk8


remove plastic gearchange cover four clips use small plastic blade down each side about 20mm from each end to release, disconnect switch connectors.remove 4 screws and metal retainers, may have spacing washers underneath.remove veneer j gate surround.remove rear centre console end held by clips just pry off carefully,remove 4 torx screws now exposed. remove centre console you may have to disconnect electrical connectors depending on vehicle spec.cig lighter on all,it will then enable the audio unit fixings to be removed make sure you remove the gearshift from P and disconnect battery before you start work

Nov 12, 2013 | 1997 Jaguar XK8

1 Answer

How do I remove passenger seat for my SC400?


4 bolts 2 located in the front and 2 in the rear, just pop up the plastic covers.

Jun 15, 2012 | 1995 Lexus Sc 400

1 Answer

I have a Dodge Caliber 1.8 SXT and want to change the transmission fluid. It is a manual transmission and if i look it up in the owners manual, it tells me to use ATF 4... is this right? Further i did take...


Yes, the ATF4 is the correct transmission fluid to use in your Dodge Caliber. As for finding the fill plug it should be a bolt screwed into the side of the tail housing midway between where the gearshift goes in and the end of the transmission. Look on both sides. If it is not there, you may be required to pull the gearshift out of the transmission, this is not hard to do. Simple remove the gearshift boot cover and there should be 4 bolts holding what is known as the gearshift inspection plate. Remove these bolts with the gearshift in neutral, pull directly up on the gearshift and it should come out of the transmission, but by all means search for a fill plug first.

Aug 09, 2010 | 2006 Dodge Caliber

1 Answer

How do you remove the broken plastic gear fromthe antenna motor 1997 lexus SC400


You will need to take the antenna motor out and take the cover apart to remove that piece. Pretty simple.

Nov 23, 2009 | 1997 Lexus Sc 400

1 Answer

2000 F150 gear shift knob no longer shifts gears


Good day
No the steering wheel don't need to be remove.
1. remove the instrument panel cluster opening finish panel assembly. remove the 3 screws that retains the upper steering column shroud and remove cover.
2. insert a scratch awl into the access hole on lower steering column shroud and push in the ignition lock cylinder release pin. insert the ignition key into the lock, turn ignition to run position and remove the lock cylinder from the steering column. remove lower steering column shroud. unsnap and slide gearshift lever boot up toward end of gearshift lever.

NOTE: ALWAYS INSTALL NEW GEARSHIFT LEVER RETAINING PIN DURING REASSEMBLY

3. remove gearshift lever retaining pin by lightly tapping with a drift punch and hammer. disconnect gearshift lever harness connector. remove gearshift lever. to install reverse removal procedure.

hope this helps

Cheers

Jul 15, 2009 | 1993 Ford F150 SuperCab

1 Answer

Removing an automatic gear shift out of a sc400


position the shifter into the drive position, pull down on the plastic trim directly underneath the leather portion of the shifter. theres two phillips head screws behind that. remove the shifter knob and the plastic piece. the trim will pop out if you pull directly upwards, disconnect the heated seats(if you have them) and the trac button. hope that helps.

Jun 09, 2009 | 1997 Lexus Sc 400

1 Answer

How do you remove the leather gearshift cover on a 6 speed 2002 corvette


the six speed in these cars is a t56 tremec trans. the gearshift knob on these are just threaded onto the shifter lever. it is regular right handed threads so just grip it tightly and turn it counter clockwise to remove the shift knob. if you are only trying to remove the leather about the only way would be to cut it off but underneath it does not look good and you have to buy a whole knob not just the leather cover to replace it.

Apr 27, 2009 | Chevrolet Corvette Cars & Trucks

1 Answer

I want to remove the head light assembly on my 1992 lexus sc400


remove the 2 10mm bolts on top that you can see, then remove front part of inner fender liner you will find 2 10mm nuts. you will need a long extension. Recomend using duct tape around feneder area to avoid scratching.

Mar 21, 2009 | 1992 Lexus Sc 400

1 Answer

I have a Mariner outboard engine which requires the water pump to be removed for repair. The gear shift linkage once disconnected from the oprating lever will not pass through the casing in the engine...


In order to disconnect the gearshift linkage from the gearshift operating handle, a safety clip was rotated about 90 degrees clockwise. Once in this position, if you pull the safety clip towards you, it comes completely out, which then permits the gearshift rod to seperate from the operating lever.

Oct 11, 2008 | 2004 Mercury Mariner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

162 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

63456 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...