Question about 2000 Toyota Tundra

2 Answers

2000 toyota tundra #5 cylinder misfire

Truck is running pretty rough and check engine light is on. Blinks for about 100 times after i start acclerating then stays on, then blinks after a little bit. had it checked, said cylinder #6 misfire. replaced spark plugs and still same. so i took the coil from 6 and put it on 2 ( to the best of my knowledge, i am not sure exactly which cylinder is which - cant find a diagram anywhere) got it checked again and said cylinder 5 misfire now! replaced the coil i moved but still runs rough and says #5 misfire. not sure what to do next. any thoughts?

Posted by on

  • 2 more comments 
  • flip722000 Jan 11, 2009

    accelerate to 50 mph and let up on the gas, the truck start to vibrate. pushing on the gas pedal, it feels like it's going to stall and vibration gets worst. help

  • COmtntundra Jan 18, 2009

    same issue. #3 cyl. is missing. the miss is so hard that its running terrible, especially under even a minor load. diagnostics shows 12-23 misfires per second. swapped coils, but problem stays with the cyl. - will install new plugs as first option. will also run a can of BG44K injector cleaner. if that doesnt do it, will likely either replace the injector or go to the dealer.

    PS: #8 cyl. showed 200,000 misses then the meter clears to zero. go figure.

  • bkh811 Feb 09, 2009

    I have a 2000 Toyota Tundra started running rough. Gave it a tune-up, changed plugs, etc. didn't help. Check engine light on, had it put on a diagnostics, came back it was misfiring on 1, 4, and 5 cyl. Any suggestions?

  • Anonymous Mar 18, 2014

    The engine has 380,000 miles and timing belt replaced at 270,000 miles. Has always run smoothly until this problem

×

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 12 Answers

I think #5 is on driver side the front one....

Posted on Dec 30, 2008

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Cylinder # 5 is on driver's side it's the 3rd. from front. I hope this help you, good luck.

Posted on Sep 19, 2012

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine misfiring, warning lights are coming in and out.digital dash trac control, overdrive off light,temp gauge shots up momentarily, and check engine light. car running rough. 2000 Grand Marquis 95k


Misfire condition on cylinder 5 (P0305) and cylinder 8 (P0308). There is a good explanation of it here :
http://troubleshootmyvehicle.com/ford/4.6L-5.4L/how-to-diagnose-misfire-codes-1

Mar 20, 2013 | 2000 Mercury Grand Marquis

1 Answer

2001 Toyota Tacoma flashing Check Engine Light and misfire...oil light will come on as well after running for a bit.


Have you tried replacing the plug wires? Change your oil and filter your filter may be plugging up and causing your oil pressure to drop.

Jan 26, 2013 | 2001 Toyota Tacoma

3 Answers

2008 Toyota Tundra engine light on, vsc off, 4lo, slip indicator lights came on - what is the problem?


I currently have the same issue on my 2008 Tundra. I have noticed that one of the 12v acces plugs don't work. The problem is intermittent and started when the air was damp or after it rained. Now the same lights are on, the 12v doesn't work and the remote door locks don't work. Toyota want to run a diagnostic check at $125 an hour. Did you solve your problem?

Aug 02, 2012 | 2008 Toyota Tundra

1 Answer

Thanks Burkerobin & PC302001-- on 2000 Tundra V-8, 4,5 & 7 cyl. misfire. Find no distributor for this engine, reset engine light/retested. More info; Truck runs great while parked-revs/idles, put...


DO A LITTLE TUNE UP.CHANGE SPARK PLUGS.CHANGE FUEL FILTER.CLEAN FUEL INJECTORS.FILL FUEL TANK UP.AND ADD A BOTTLE OF FUEL INJECTOR CLEANER IN FUEL TANK.WHEN YOU DRIVE CAR AROUND.THE INJECTOR CLEANER WILL CLEAN OUT FUEL INJECTORS.IF CAR STILL RUN ROUGH IN DRIVE.YOU COULD HAVE INTAKE LEAK.

Jan 30, 2010 | 2000 Toyota Tundra

3 Answers

VSC OFF, Check engine and traction control lights are on


I would suggest having your mechanic scan the computer for viable trouble codes. WIthout that information, it is hard to determine the exact cause of your problem.

However, my experiences with the Tundra leads me to suggest that you have a bad Mass Air Flow Sensor...A concise scan and any codes would alow us to really help you out a lot better.

Sep 17, 2009 | 2007 Toyota Tundra

1 Answer

Misfiring


See what cylinder is loosing (if that's it) spark. Use a spark tester if you can, or remove plugs and turn it over with the wires on all of the plugs, grounded!

Jul 29, 2009 | 2000 Toyota Tundra

2 Answers

2000 Toyota Tundra 4.7L V8 Rough Idle


Clean/Inspect Intake, MAF sensor, IAC valve for proper operation. Also check for vacuum leaks within the air intake hose and intake components. Hopefully this helps

Jul 20, 2009 | 2000 Toyota Tundra

3 Answers

My 2007 Toyota Tundra 4.7l shows VSC OFF lights


check air filter for dirty , how many miles or kms have your car? , maybe need to replace spark plugs, try to reset the ecu for a momentany malfunction, remove the negative battery terminal few minutes and reconnect,start engine and drive, check if lights goes off , please write me

Jul 04, 2009 | 2007 Toyota Tundra

1 Answer

OBD2 read Misfire on 2,3 and 4 cylinders


p code will translate more of your problem what is p codes pls

Dec 10, 2008 | 1994 Toyota T100

Not finding what you are looking for?
2000 Toyota Tundra Logo

1,996 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

63661 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21981 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...