Question about 2005 Chevrolet Suburban

1 Answer

2005 Chevy Suburban Ignition Switch

I've checked the engine, checked out good. I've checked the started check out good. I got new spark plugs just hoping. I've checked the cables and they are fine, but I don't know where or how to check the ignition switch does anyone know?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 78 Answers

The ignition switch,is on bottom of the steering column. The key just moves a rood hocked to the switch. It can adjusted losening two small screws, and sliding it up or down. Check it by pulling the conector and using an owm meter.

Posted on Dec 29, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do fix my 2005 chevy equinox


If the engine is cranking properly, then the problem either has to be in ignition or fuel delivery systems. And if you have an automatic, you might want to check the neutral safety switch for proper operation. And do not ignore the ignition switch.

Jul 18, 2015 | Cars & Trucks

2 Answers

What should I check now??? my 2005 chevy suburban died while going down the road and now it wont start.


Lets start at the beginning.
Do you have spark to the plugs and normal fuel pressure ?

Aug 24, 2014 | 2005 Chevrolet Suburban

2 Answers

2002 CHEVY SIVERADO NO SPARK


check at the key lock and cylinder and the ignition switch, GM has had a lot of issues with this problem on a number of vehicles. The coil pack needs to receive the signal from the ignition to complete the circuit, if no signal from the switch, it will not produce any codes and cause a no spark issue. I would start with testing the switch with a multimeter for a resistance reading.

Nov 25, 2012 | Chevrolet Cars & Trucks

1 Answer

My 2004 Chevy suburban won't start but there is a locked padlock on dashboard , is this why?


sound like problem in the theft security systm,try this insert another key in the ignition switch, the other key could be worn where pcm and bcm dont recognize it. and switch ignition on engine off watch padlock symbol with ignition switch left on 10 minutes the padlock symbol will extinguish or turn off then you will turn off ignition switch wait 5 seconds then try starting vechicle if start your theft security failing need let dealership check it out.

Aug 27, 2012 | 2004 Chevrolet Suburban

2 Answers

I have a 2004 Chevy Suburban 1500 with 103,000 miles. I am having problems when starting. When the key is turned, the engine will turn over but not start. Turn the key back to off and re-start and the...


Check for power out of the ignition switch. It sounds like the ignition switch is not engaging on the first try and its taking that second turn to get power from the switch to the ECU and so forth. I would replace the switch and possibly the tumbler if the key comes out while the vehicle is running.

Jun 21, 2011 | 2004 Chevrolet Suburban

4 Answers

There is no spark thus car won't start. the battery is fine, it turns over good, it is not flooded, the spark plugs are new, the ignition coil was just replaced, what else controls the spark


The Crankshaft Position Sensor and the Ignition Control Module also control the spark. It depends on whether your vehicle is equipped with the 2.2L engine or the 2.4L engine as to where these components are located and what they look like.

Jan 29, 2011 | 1996 Chevrolet Cavalier

1 Answer

Random misfire after new spark plugs and wires


Check the firing order. If it wasn't happening before then that's most likely your culprit. For a 2005 Chevy Suburban the firing order is as follows;
1-8-7-2-6-5-4-3

Another thing to check is resistance in the plugs and wires. Check to make sure they all have the factory specified resistance.

Jan 01, 2011 | 2005 Chevrolet Suburban

3 Answers

My 2005 chevy malibu classic will not start i have everything checked out also my theft system light is on constantly


all gm vehicles from 97-2005 have a theft system called the passlock system. (how to deactivate system on chevy malibu) turn key on engine off, let it stay on for at least 10 minutes, then turn ignition off, take out key from ignition switch. after 1 minute start the car. you can also go to tubesound.com to disable system for good. --tubesound.com/passlocksystem. ( just type in the problem when page comes up ). have a good day!! vehicle will not start with system blinking. it thinks its being stolen.

Sep 10, 2010 | 2005 Chevrolet Malibu

1 Answer

1994 chevy suburban, no fuel coming from fuel


Put an injector noid light at the injector plug terminals to see if your getting a signal from the PCM(computer).If not try to find a computer from the same vehicle that works and swap it into yours to check.A PCM swap will take about 15minutes.

Sep 23, 2009 | Chevrolet Suburban 1500 Cars & Trucks

Not finding what you are looking for?
2005 Chevrolet Suburban Logo

186 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

60769 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6811 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...