Question about 1995 Jeep Cherokee

1 Answer

1995 jeep grand cherokee

How to replace a ignition lock clyinder on a 1995 jeep grand cherokee

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 475 Answers

Steering wheel has to come off and airbag disconnected (by a qualified tech or it can blow open in your face) speacial tool needed for steering column clip removal and install, should I go on?

Posted on Mar 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change an ignition switch for my 95 jeep grand cherokee


Try here
https://www.2carpros.com/questions/1995-jeep-cherokee-1995-jeep-cherokee-ignition-switch-replacement

Sep 27, 2016 | 1995 Jeep Grand Cherokee

1 Answer

1996 grand cherokee L.E. rear brakes locking.


Check you ebrake cable that is attached to brake shoes.Also check wheel cylinders.

Aug 26, 2012 | 1996 Jeep Grand Cherokee

1 Answer

Jeep grand cherokee alarm system


The 1995 Jeep Grand Cherokee Laredo Anti-Theft System is equipped with Vehicle Theft Security System (VTSS). VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running.

The following wiring diagram and electronics circuit contains detail schematics of The 1996 Jeep Grand Cherokee Laredo Anti-Theft System. Herein you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Try HERE and also, remember that here can find the Jeep Grand Cherokee Service Repair Manual.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Nov 25, 2011 | 1995 Jeep Grand Cherokee

1 Answer

How do I know if my ignition switch is bad on my 1995 jeep grand cherokee lerado 5.2 liter


The ignition switch does not usually go bad on Grand Cherokees but the ignition key cylinder does and it usually just stop turning, stuck in place. Key cylinder can be removed by taking the steering wheel off to access the little clip that's holding the key cylinder in place, inside the steering column.

Jul 27, 2011 | 1995 Jeep Grand Cherokee

1 Answer

1995 jeep grand cherokee. When I turn the key on, the warning chime stays on, a solid tone. I took the chime box out, but the power locks do not work properly.


most likely a short in the ignition cylinder and it's housing, ( were the key goes). if you dont want a new cylinder and housing you may be able to disconnect the connector by the housing. you will have to remove the plastic cover from the steering column.

Jun 09, 2011 | 1995 Jeep Grand Cherokee

1 Answer

I lost my keys and there are two different keys to operate my jeep. One opens the door, and the other ones starts the car. Can I get a new set?


Sounds like somewhere along the life of your jeep someone changed the ignition cylinder, resulting in your having two separate keys. You will have to replace the ignition cylinder and all or maybe just the one driver's side door lock cylinder. There's really no way one key will work with both your existing ignition and door locks. Another suggestion is that you can get a complete matching set of locks and keys from someone who's parting out their Grand Cherokee, so you would then have only one key for all the locks.

Feb 02, 2011 | 1995 Jeep Grand Cherokee

1 Answer

Remote lock no longer works


replace remotes from dealer possible water damage in remotes

Apr 21, 2009 | 1995 Jeep Grand Cherokee

1 Answer

1995 Grand Jeep Cherokee


The lower speeds are controlled by a resistor block. That's what needs to be replace. It's usually located next to the blower. It will have electrical wires connected to it. High speed bypasses the block so it alway works.
If you want to replace it then;
) Disconnect the battery negative terminal if the vehicle have air bags. Wait 2 minutes for system to discharge.
) Remove the kick block on the passenger side. )Remve the glove box ) Remove the bolts holding the blower motor resistor. Push the red lock up and press down on the click ) Pull the block out. ) Install new block and reverse steps above.

Apr 13, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Keys wont work


A little Costly, But contact a Locksmith to make you a New key from the Door lock or the Glove box lock,"If it's the same key"

Cost could be up to $150, Or as low as $45 an Hour.

A good locksmith Should be able to help in 30 to 45 min's

Feb 04, 2009 | 1995 Jeep Grand Cherokee

1 Answer

Ignition Problems


you can try spraying P.B. Blaster into lock clyinder sounds like a pin is sticking in lock or the key is worn... if thats doesnt work replace lock clyinder.....

Dec 10, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Cherokee Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

61037 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...