Where is the pvc valve on a ford ranger 2001 4.0

Relatively simple gig. Remove wires from plugs making sure to note which leads to which plug so that firing order is maintained on re-installation, remove vacuum hose from pvc valve, remove six valve cover retaining bolts and remove valve cover. Clean that up making sure there is no residue on gasket mating surface on wither the valve cover itself or the top side of the header. place new gasket in place and replace valve cover torquing bolts to appx. 72-108 inlb. Replace pvc vacuum line followed by plug wires and you\'re set. This is a stripped down version as there will be many hoses and lines in the way but you should just be able to wiggle past these. If you do end up taking anything else out just make sure you remember where and how it connect and you\'ll do fine. Nothing this high up is that terribly sensitive. Good Luck!

Mar 01, 2014 • 1987 Ford Ranger

1helpful

1answer

Where is the PVC valve located on a 98 ranger

Most likely in the valve cover...it would be helpful to know what engine we are talking about.

Mar 12, 2011 • 1998 Ford Ranger SuperCab

2helpful

1answer

A 1994 Ford Ranger, complete tuneup, new plugs, wires, rotor, distributor cap, the works. The PVC valve is ok and there is suction at the PVC hose. The large hose going into the PVC. This engine is a 3.0...

Fuel injectors, sounds like on the bad

Mar 27, 2010 • 1994 Ford Ranger Supercab

0helpful

1answer

I can not find the pvc valve for a 1990 ford ranger 2.3L

it is deep under the intake manifold near center it is on top of a sheet metal box that bolts to the block

Feb 21, 2010 • 1991 Ford Ranger Supercab

4helpful

2answers

How to replace pvc valve

SECTION 303-08: Engine Emission Control 2001 Escape Workshop Manual REMOVAL AND INSTALLATION Positive Crankcase Ventilation (PCV) Valve —2.0L Zetec Removal and Installation

Remove the PCV valve (6A666).
- Remove the crankcase ventilation hose (6853) from the PCV valve (6A666).
- Remove the PCV valve from the grommet.

Dec 31, 2009 • 2001 Ford Escape

4helpful

1answer

Were is the pcv valve located on 94 ranger

look around for your throttle body, the pvc valve is usually connected to a rubber tube and connects the engine and throttle body. check the throttle body for a small rubber tube and follow it..if it leads to the engine area and is connected by i believe a "L" shaped plastic piece, thats your pvc valve

Dec 02, 2009 • Ford Ranger Cars & Trucks

0helpful

2answers

1993 ranger 2.3L reg. cab

Are you smelling gas in your oil? because the throttle body is not connected to the valve cover.

Aug 15, 2008 • 1993 Ford Ranger SuperCab

Question 2

Anonymous

Contributor 19 Answers
Posted on Oct 04, 2012

Anonymous

Contributor

Joined: Jul 22, 2012

Answers

19

Questions

0

Helped

8697

Points

62

Drivers side valve cover, facing the firewall. There's a coolant line snapped into it. Remove the rubber elbow, removed the coolant line and untwist the PCV Valve.

Answer 2 · 1/26/2009 12:00:00 AM

Anonymous

5158 Answers
Posted on Jan 26, 2009

SOURCE: Ford Ranger PCV valve.

should be on the valve cover... goes into the cover thru a rubber gromet with a vacuum hose attached.

Robert

dave smith

94 Answers
Posted on Feb 27, 2009

SOURCE: where is the pcv valve located on a 2003 ford ranger

The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.

Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.

Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.

Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.

Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.

When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.

Anonymous

195 Answers
Posted on Jul 01, 2009

SOURCE: 2001 Ford Ranger V6 timing chain

Hello;
The Ford motors are pretty good. I had 280K on a 2.9 V-8 that only needed the oil changed every 3K. Unless you have fluctuatuation in the timing then you should be ok.
These engines use a chain rather than a belt and have excellent life.
Thanks;
Rich RPM Northwest

Anonymous

22 Answers
Posted on Oct 20, 2009

SOURCE: i need a diagram of a 2001 mazda tribute engine ,

Get a haynes manual they are priceless. Check out Ebay

Anonymous

4669 Answers
Posted on Mar 27, 2010

SOURCE: A 1994 Ford Ranger, complete tuneup, new plugs,

Fuel injectors, sounds like on the bad

Testimonial: "thanks."

Answer 3 · 1/26/2009 12:00:00 AM

Anonymous

5158 Answers
Posted on Jan 26, 2009

SOURCE: Ford Ranger PCV valve.

should be on the valve cover... goes into the cover thru a rubber gromet with a vacuum hose attached.

Robert

Answer 4 · 2/27/2009 12:00:00 AM

dave smith

94 Answers
Posted on Feb 27, 2009

SOURCE: where is the pcv valve located on a 2003 ford ranger

The PCV valve can be located in several places. The most common location is in a rubber grommet in the valve cover. It can be installed in the middle of the hose connections, as well as installed directly in the intake manifold.

Once the PCV valve is located, make sure all the PCV system hoses are properly connected and that they have no breaks or cracks.

Remove the air cleaner and inspect the air and crankcase filters. Crankcase blowby can clog these with oil. Clean or replace such filters.

Oil in the air cleaner assembly indicates that the PCV valve or hoses are plugged.

Make sure you check these and replace the valve and clean the hoses and air cleaner assembly.

When the PCV valve and hose are in satisfactory condition and there is oil in the air cleaner assembly, perform a cylinder compression test to check for worn cylinders and piston rings.

Answer 5 · 7/1/2009 12:00:00 AM

Anonymous

195 Answers
Posted on Jul 01, 2009

SOURCE: 2001 Ford Ranger V6 timing chain

Hello;
The Ford motors are pretty good. I had 280K on a 2.9 V-8 that only needed the oil changed every 3K. Unless you have fluctuatuation in the timing then you should be ok.
These engines use a chain rather than a belt and have excellent life.
Thanks;
Rich RPM Northwest

Answer 6 · 10/20/2009 12:00:00 AM

Anonymous

22 Answers
Posted on Oct 20, 2009

SOURCE: i need a diagram of a 2001 mazda tribute engine ,

Get a haynes manual they are priceless. Check out Ebay

Answer 7 · 3/27/2010 12:00:00 AM

Anonymous

4669 Answers
Posted on Mar 27, 2010

SOURCE: A 1994 Ford Ranger, complete tuneup, new plugs,

Fuel injectors, sounds like on the bad

Testimonial: "thanks."

Related Topics:

Where is the pvc valve on a ford ranger 2001 4.0

1 Answer

Anonymous

5 Related Answers

Anonymous

dave smith

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Change a pcv valve 2006 ford ranger4.0 4x4

Need the location of PVC valve on 1999 Ford Ranger 3.0 engine?

Where is the pcv valve located on a 88 ford ranger with a 2.0 engine

How to replace a valve cover gasket on my 1987 Ford Ranger with a 2.0 L engine

Where is the PVC valve located on a 98 ranger

A 1994 Ford Ranger, complete tuneup, new plugs, wires, rotor, distributor cap, the works. The PVC valve is ok and there is suction at the PVC hose. The large hose going into the PVC. This engine is a 3.0...

I can not find the pvc valve for a 1990 ford ranger 2.3L

How to replace pvc valve

Were is the pcv valve located on 94 ranger

1993 ranger 2.3L reg. cab

Not finding what you are looking for?

Cars & Trucks

Change a pcv valve 2006 ford ranger4.0 4x4

Ask a Question

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

ZJ Limited

john h

Arnie Burke

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

DIS9_Full.pdf. user-manual-1994...

DIS9_Full.pdf. user-manual-1994...

Rhonda_Docs.pdf. user-manual-2001...

Related Topics:

Where is the pvc valve on a ford ranger 2001 4.0

1 Answer

Anonymous

5 Related Answers

Anonymous

dave smith

Anonymous

Anonymous

Anonymous

Add Your Answer

Attachments: Added items

Related Questions:

Change a pcv valve 2006 ford ranger4.0 4x4

Need the location of PVC valve on 1999 Ford Ranger 3.0 engine?

Where is the pcv valve located on a 88 ford ranger with a 2.0 engine

How to replace a valve cover gasket on my 1987 Ford Ranger with a 2.0 L engine

Where is the PVC valve located on a 98 ranger

A 1994 Ford Ranger, complete tuneup, new plugs, wires, rotor, distributor cap, the works. The PVC valve is ok and there is suction at the PVC hose. The large hose going into the PVC. This engine is a 3.0...

I can not find the pvc valve for a 1990 ford ranger 2.3L

How to replace pvc valve

Were is the pcv valve located on 94 ranger

1993 ranger 2.3L reg. cab

Not finding what you are looking for?

Cars & Trucks

Change a pcv valve 2006 ford ranger4.0 4x4

Ask a Question

Popular Questions

Toyota dashboard CD player won't eject

4.3 Firing order diagram for 4.3L v6 Chevy engine

BMW X5 Trans Fail Safe Program,

Diagram of 1996 ford ranger fusebox which fuse is

What does my check engine light trouble code $7e8 mean?

Check Out the Latest Top Trucks Report!

Top Cars & Trucks Experts

ZJ Limited

john h

Arnie Burke

Are you a Car and Truck Expert? Answer questions, earn points and help others

Manuals & User Guides

DIS9_Full.pdf. user-manual-1994...

DIS9_Full.pdf. user-manual-1994...

Rhonda_Docs.pdf. user-manual-2001...