Question about 1999 Chevrolet Silverado 1500

1 Answer

Pulling the 4x4 shifter

How do i pull the 4x4 shifter handle?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 71 Answers

Put it neutral then move the lever; if still stuck, roll the vehicle front or back and continue to try till the gear splines mesh; good luck. ps. if electronic and that doesn't work, the ck the fuses.

Posted on Dec 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

REMOVING STOCK SHIFTER FOR 4X4 ON 07 WRANGLER


The 4WD shifter knob on the 2007 JK's is ridiculously hard to remove. Pull straight-up with all your might, then after that fails, get some towels, and a chunk of would with a long pry bar. Hopefully you won't crack your center console.

Mar 19, 2014 | 2007 Jeep Wrangler Unlimited Rubicon 2...

1 Answer

My shifter quit working


On a console shift auto, you need to remove the shifter handle by pulling out the clip on the side of the the T shifter with a needle nose pliers.. Pull handle up. There is a plastic bead strip with 3 or 4 balls on it. The clip needs to be re-installed so that the clip holds the strip in place. If this does not work the strip needs to be replaced.

Sep 03, 2012 | 1989 Pontiac Firebird

1 Answer

How do i replace the plastic handle on my automatic shifter for my ford f150 2006 lariat


I assume you have a console floor shifter...You may need to pull shifter all the way back to low gear to see...look near the bottom on the back side of the handle...you should find a removeable screw or pull out clip...after removing this, the handle should lift off...New handles are roughly $35. at your Ford dealer...or they are plentiful in your nearest salvage yard...Hope this helps.

Feb 01, 2011 | Ford F-150 Cars & Trucks

1 Answer

I need to remove the shifter handle on my 2000 firebird so i can adjust the link cable for the automatic trany. so can you help guide me through removing the shifter handle?


Hello: on the part of the handle facing the dash there will be a small piece of metal going across the shifter, this will be close to where the metal part of the shifter. Use a small flat blade screw driver and pull it out (toward the dash) once out the handle should come off(pull up)

Dec 14, 2010 | 2000 Pontiac Firebird

3 Answers

Gear shifter stuck on P. Won't move, and button, 1994 El Dorado


have the shift lock interlock solenoid checked out

Jul 29, 2010 | 1994 Cadillac Eldorado

2 Answers

98 Pontiac Trans am automatic trans...


The front of the handle has a large "U" clip. Use a screw drive and pry the clip out. It's a lot easier to do when the shifter is pulled all the way back to "1" or "2" but is doable in park still. The handle will then pull up. There will be a plastic piece in it that pushes down to release the lock in the shifter assembly. If when you push the plastic piece down it doesn't release the lock you will have to remove the shifter cover and take a look inside, to see what broke. It may require replacing the whole shifter assembly. You should be able to find the complete assembly used for fairly cheap.

Jan 02, 2010 | 1999 Pontiac Firebird

1 Answer

How do i use four wheel drive


if you have 4x4 in your sportage then pull the 4x4 shifter down and you'll be in 4high put it in neutral and push the shifter to the right and up to be in 4 low

Dec 06, 2009 | 1999 Kia Sportage

1 Answer

96 Jeep GC Shifter Removal


To remove the shifter handle you have to give the handle a good pull upwards. To put it back, give it a good smack down. The handle just snaps in place.

Jan 08, 2009 | 1996 Jeep Grand Cherokee

1 Answer

How do i take the shifter handle out of a jeep


pull the U clip from the side of the handle under the push knob
then the shifter handle will pull right up off the lever

Dec 31, 2008 | 1998 Jeep Cherokee

2 Answers

1988 suzuki samurai WONT MOVE


First thing just try to push or pull the 4x4 lever if you get it to move and it feels like it went into some gear try to drive the truck.If this works look on the shifter for the 4x4 and put it in 2 wheel drive (H2 is two wheel drive,H4 is 4x4 high,and L4 is 4x4 low range).Make sure you have the clutch depresed when you try to move the 4x4 lever.If you try this stuff with no fix try and look for clutch adjustment on the transmision you may need to adjust it or your clutch is bad.

Aug 30, 2008 | 1988 Suzuki Samurai

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

63990 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21990 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...