Question about 1984 Ford Bronco

1 Answer

84 ford bronco 2 thermostat

My 84 bronco had no thermostat in it. i went to put a new one in and the hosing that sits over top of it cracked. i ordered a new one to replace it with. at the parts store the guy sold me the thermostat, the gasket, and a circular cork gasket. i can't figure out where the cork gasket is supposed to go. also does anyone know hoe the thermostat fits in? is it bell up or down? anything would be a great help.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 651 Answers

Tha gasket goes on the housing, the copper side should go down.

Posted on Dec 29, 2008

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the thermostat located on a 1997 ford Taurus SHO?


Trace the top radiator hose back to the engine. Where it ends is the thermostat housing. You'll have to drain your radiator, remove the radiator hose at the housing on the engine side, then there's usually 2 bolts that hold the housing on. remove the housing, remove the thermostat Noting which direction the thermostat is sitting, replace with the new one in the same position, put a new gasket on the thermostat housing and reverse your steps to put it back together. NOTE**** DO NOT OVER TIGHTEN THE THERMOSTAT HOUSING BOLTS*** if you strip them or snap them off you will be looking at a major repair bill.

Feb 14, 2015 | 1997 Ford Taurus

1 Answer

1995 ford bronco 5.8 VL thermometer gasket housing


Hi Jeffy, I'm glad to help!
Jeffy, you'll need to take the housing back off and make sure the matting sufaces or clean enough to eat off of. You see, if there is only a tiny little piece of dirt or old gasket material left on the surface it will lift the gasket up and allow it to leak. NOTE: Also check the surfaces after cleaning them throughly and see if there are any scratches or cracks. NOTE: Also, if you are replacing a thermostat, then you'll also need to clean the are where the thermostat sits, so that it will sit all the way down because if its sitting up to high it will also cause a leak. Hope this helps and have an awesome day Jeffy.

Feb 22, 2014 | Ford F-250 Cars & Trucks

1 Answer

Can i put a 84 bronco 2 tranny mazda type 14 bolt pan in a 88 bronco 2 that originally had a 12 bolt pan both 4wd


well if it is a 1984 tranny it is a toyo koygo tk4 or tk5, which if mounted in the 84 bronco the transmission sets at a tilt, which means that the transmission crossmember bolts into the frame at a angle.. the mazda tranny was used in 88-90 the transmission crossmember sets straight across and bolts on to the frame on each side with one bolt.. with some major fabricating it is possible but to simply change out nope wont fit..

Jan 28, 2011 | 1988 Ford Bronco II

1 Answer

84 bronco 2 over heating


Check coolant level, then thermostat, then water pump circulation. If all are good then jump to head gasked, cracked head or block...

Dec 18, 2009 | 1984 Ford Bronco II

1 Answer

How to replace the front brake hose on an 84 ford


should be a bolt where the hose enters the front caliper. just unhook and replace with new one. Be forewarned. When you change out the lines, you need to bleed the brakes as well.

Oct 07, 2009 | Ford Bronco II Cars & Trucks

1 Answer

Drive belt configuration for 84 B II


Yours Maybe Missing But Ford Puts A Sticker On The Front Crossmember At The Radiator Somewhere Close To The Hood Latch It Shaws The Belt Routing For Your Vehicle's Engine Hope This Help's

Jul 16, 2009 | 1984 Ford Bronco II

1 Answer

Put in themostat


Hello

The thermostat is located in the housing at the end of the lower radiator hose. It sits in part of the water pump. Hope this helps

Apr 05, 2009 | 1987 Ford Bronco II

1 Answer

No heat or defrost


Thermostat is not on the radiator. It is in a housing on the intake manifold at the engine end of the top radiator hose.Heater controls on that truck may be vacuum controlled or cable controlled You need to check and make sure that the heater lines are open and water is flowing through them.

Jan 27, 2009 | 1986 Ford Bronco

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

289 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

70387 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22041 Answers

Ron Lankford

Level 3 Expert

5386 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...