Question about 2006 Hyundai Tucson

Open Question

The alarm system

I want to reset the keyless factory alarm the honk don't make any sound when the system is active.
thanks

Posted by on

  • philip van rensburg Jan 22, 2009

    I WANT AN AUDIBLE SOUND WHEN USING THE REMOTE TO LOCK AND UNLOCK THE CAR.

×

6 Suggested Answers

  • 41 Answers

SOURCE: 1996 Grand Cherokee keyless entry problem

That remote should not be able to  be programmed by you, it needs to be programmed by the dealer using their computer.  I know that some later and earlier models can be programmed by the user, but I did some research on this as i have a 96 as well and it seems the 96 was a dealer computer thing.  If you in fact bought the remote from the dealer they should be willing to program it for FREE.  Otherwise I was given a $30 estimate for the programming.

Posted on Dec 12, 2008

  • 2 Answers

SOURCE: 2006 aveo alarm system

this happened to me and it drove me crazy for a few days. check that the hood is closed tightly. its held shut for the most part by a peice of metal with a screw on one side, a spring around it, and a nub looking shape that fits into the locking device above the bumper. When i finally checked my hood, the entire bit of metal had come unscrewed and was stuck in the locking device, leaving my hood held shut only by the safety clamp. remove it from the locking part and screw it back into the hood, closing it a few times to find the right distance to screw it in. lock your car and hear that chirp, that should fix it

if thats not the case then check that all of the doors are closed nice and tight... if the doors lock but the audible alarm is not armed then that is most likely the case

Posted on May 19, 2009

ghost4548
  • 776 Answers

SOURCE: program factory remote keyless entry for 2003 Hyundai XG350

This bulletin supersedes TSB# 02-90-001.
DESCRIPTION: The security system keyless adapter cable (SPX/Kent-Moore P/N 09900-21300) is a special service tool (SST) that is used for programming new keyless entry remote transmitters to the factory security systems. The keyless adapter is used in conjunction with the Hi-Scan Pro (with Hi-Scan SOL Pro Software Version 09-29-03
or newer) and Data Link Connector (DLC) Cable. SERVICE INFORMATION: The keyless adapter cable can be used on the following vehicles:

  • 2001 - 2004 MY Elantra
  • 2001 - 2004 MY Santa Fe
  • 2002 - 2004 MY Sonata
  • 2001 - 2004 MY XG300/350 0390020a.gif
NOTE
  • The 2003 - 2004 MY Tiburon does not need the Keyless Adapter Cable to add keyless entry remotes to the factory security system. Instead, the Hi-Scan Pro connects to the vehicle using only the DLC cable. See page BE-60 in the 2004 MY Tiburon Shop Manual for the latest instructions.
  • The most current Keyless Adapter Cable Instructions are available in the following shop manuals:
SHOP MANUAL

PAGES

2004 MY Elantra
BE-73 - BE-74
2004 MY Santa Fe
BE-43 - BE-44
2004 MY Sonata
BE-40 - BE-41
2004 MY XG350
BE-46 - BE-47
KEYLESS ADAPTER CABLE INSTRUCTIONS:
  1. Connect the keyless adapter cable to the Hi-Scan Pro DLC cable. 0390020b.gif
  2. Plug the keyless adapter into the vehicle's 10-pin multi-purpose connector located behind the driver's side lower instrument panel (next to the DLC). NOTE Sample vehicle shown is the Santa Fe.
    0390020c.gif
  3. Turn the Hi-Scan Pro ON
    and press ENTER
    . NOTE "Release date 29. Sep. 2003" OR LATER
    must appear on this screen. To update your SOL card with the latest software go to www.hmaservice.com and refer to TSB 00-00-001.
    0390020d.gif
  4. Select option "HYUNDAI VEHICLE DIAGNOSIS"
    and press ENTER
    . 0390020e.gif
  5. Select vehicle model and press ENTER
    . 0390020f.gif
  6. Select option "TRANSMITTER CODE SAVING"
    and press ENTER
    . 0390020g.gif
  7. Ensure that the key has been removed from the ignition cylinder before proceeding. 0390020h.gif
  8. Follow the steps noted on the Hi-Scan Pro screen to program the remote(s). NOTE The factory security system can only be programmed to accept two remote transmitters and MUST be programmed for both remote transmitters at the same time.
    0390020i.gif
  9. Press ESC
    on the Hi-Scan Pro and verify that the remote(s) are functioning properly.
  10. Turn the Hi-Scan Pro OFF
    and disconnect the adapter cable from the multi-purpose connector.

Posted on May 31, 2009

  • 1 Answer

SOURCE: Alarm system sounds off for no reason ('97 Lesabre Limited)

I had the same problem. The alarm system on my 1997 Le Sabre self-actuates. Luckily, it went off once when I popped the trunk. I went to Auto Zone and bought a generic trunk replacement lock. I noticed the original lock had a funky push-pull type of switch used to activate the alarm. This switch was likely hair-line on/off and when the temperature changed, it activated.

I went ahead and replaced the lock without the switch, but you can try simply unplugging the switch through the hole in the metal behind the lock to see if that might stop the alarm from arming itself (or cut the wire).

Good luck, it's a "hairy" problem.

Posted on Jun 14, 2009

  • 197 Answers

SOURCE: 2007 Rav4, 41,700 miles. Today car will not start.

check if their is a fuse for the relay for the starter might be blown

Posted on Jul 24, 2009

  • 462 Answers

SOURCE: the factory alarm on my 2009 Toyota Rav4 was

Try to close doors and lock it with the key , not remote.
Then take the key out , wait 20-30 sec. and unlock it with the key.
After that try to start engine.

Posted on May 27, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I want my isuzu sportivo 2006 to activate again the alarm sound of my keyless entry


Check the owners manual the horn honk when alarm is activated is in most cars an option that can be turned on and off. Also does the horn work with the steering wheel button?

Jul 02, 2012 | Cars & Trucks

2 Answers

I can't turn off the security alarm on my 1998 nissan pathfinder


Reset procedure: Disconnect the Positive Battery Cable.
Open Drivers Door & LEAVE open
Turn Ignition Switch to On & Leave On
Reconnect Positive Battery Cable
Horn may sound for a few seconds
Start Vehicle
If Alarm does not reset, then the Alarm Module is probably defective

Jun 12, 2012 | 1998 Nissan Pathfinder

1 Answer

Bought from dealer with no keyless entry. alarm activates when doors are locked with power doorlock system. alarm sounds when we open the door. how do we de-activate the alarm before unlocking the door?


Opening the drivers door with the key is supposed to shut down the factory security but the drivers key cylinder usually goes bad. You will have to unlock the rear tail gate lock cylinder with the key and that will shut down the factory security, before opening the drivers door.Your other option is to have an aftermarket keyless entry system installed, which will open the doors remotely while shut down the factory security at the same time.

Jan 25, 2011 | 1996 Jeep Grand Cherokee

2 Answers

Keyless remote locks the doors but the horn doesn't honk.


Your lock settings were most probably changed from your remote unit. By pressing both lock and unlock keys together for around two to three seconds you can switch between silent mode and horn mode. Hooe that helps...

Sep 16, 2009 | 2002 Nissan Altima

2 Answers

Can I stop my horn from sounding when I lock my 2009 Accord


You might can have the dealer program it not to honk, but its just the way the keyless entry works. I've owned 2 accords--an 06 and 08--and both of them honk the horn when the lock button is pressed twice. Pressing the button once will secure the car and arm the alarm. So once click is all you really need. And no your alarm is not malfunctioning.

Jul 18, 2009 | 2006 Honda Accord

1 Answer

How can I reset my Factory Alarm on my Jeep it wont run


Alarm Module Reset Procedure
NOTE: This information applies to a Vehicle Theft Security System (VTSS) that was armed when the battery was disconnected and reconnected.
When the armed VTSS senses that the battery has been disconnected and reconnected, it enters its power-up mode. In the power-up mode the alarm system remains armed following a battery failure or disconnect. If the VTSS was armed prior to a battery disconnect or failure, the system will have to be actively or passively disarmed following a battery reconnection.
The power-up mode will also apply if the battery goes dead while the system is armed and battery jump-starting is attempted. The engine no-run feature will prevent the engine from starting until the alarm system has been actively or passively disarmed.
Passive disarming of the Vehicle Theft Security System (VTSS) occurs when the vehicle is unlocked using the key to unlock either front door or the lift gate. Active disarming of the VTSS occurs when the vehicle is unlocked by depressing the Unlock button of the Remote Keyless Entry (RKE) transmitter.
Once the alarm has been activated (horn sounding, lights flashing, and the engine no-run feature), either disarming method will deactivate the alarm.
Depressing the Panic button (if equipped) on the RKE transmitter will also disarm the VTSS, but the horn will sound and the lights will flash for about three minutes as part of the Panic feature. The horn and lights can be stopped by pressing any of the RKE transmitter's buttons or driving the vehicle above 15 mph.

Jan 28, 2009 | 1999 Jeep Grand Cherokee

1 Answer

My Truck honks 1 time randomly when alarm is activated


This is a factory system? don't remember any LED in a factory system.

Nov 25, 2008 | 2004 Ford F150

1 Answer

Keyless remote still works but the alarm system and horn seems to be deactivated. What could be the problem?


If you look in the jeeps owners manual for the keyless remote section, you can program the horn to honk or not honk when you lock the doors.

Oct 03, 2008 | 2002 Jeep Liberty

1 Answer

After market alarm went off and could not be reset. disconnected the system that was tapped into the ignition wires. still no power to anything including lights power locks windows ect. black box mounted...


what year is the Mustang? It does sound like the factory keyless entry module and the clicking is a relay inside of it. In order to disable the clicking, you would need the factory keyless entry remote or the aftermarket alarm system would have to be correctly wired to the vehicle's alarm disarm wire. A professional stereo shop would be able to handle this for you.

Aug 02, 2008 | Ford Mustang Cars & Trucks

Not finding what you are looking for?
2006 Hyundai Tucson Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

6812 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...