Question about 1993 Chevrolet K1500

1 Answer

Trans isit hard to change the output shaft

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chevrolet Master
  • 6,982 Answers

I honestly don't remember... it runs through drums etc inside unit and If I remember right, it has a retainer somewhere in there. I haven't done a swap like this in a long time but generally, GM does not make a seperate unit for 2wd & 4x4s except for tailshaft.

Posted on Dec 29, 2008


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Is there any difference if any at all on the tail

A quick tip for you. Believe it or not the shape of the oil pan gasket is often the key to knowing if they are compatible. if the gaskets are the same shape they are likely the same.

Jan 06, 2015 | Cars & Trucks

2 Answers

Will a chrysler engine go into a chevy truck

It would certainly be much easier to stay with a GM drive train.
Everything the Chrysler setup touches would need to be modified.
Wiring, exhaust, cooling, even the driveshaft. And that work would make the truck worth much less than if it had a stock drive train.

Jan 27, 2014 | Cars & Trucks

1 Answer

Cv shaft has a lot of play where its pinned to trans , bad cv or trans output shaft?

hi it would more than likely be a bad cv as the trans would vibrate or knock if it had excess play in the shaft

Apr 07, 2011 | 1993 Subaru Loyale

1 Answer

I have a 2000 AWD Chrysler Town and Country. I need to change the output shaft oil seal on the transfer case that goes to the prop shaft and to the back axle. Do I drop the prop shaft down and then...

you are correct on the whole sequence you explanined, just be sure to have a pan to catch the fluid that will come out of the trans when you pull the output shaft out.. as far as how tight to put the nut back on, cant really anwer that doesnt have a crush sleeve or anything in to to worry about messing up, so as long as its tight you will be fine, just dont crank on it excessively.

Dec 05, 2010 | 2000 Chrysler Town & Country

1 Answer

How hard is it to replace rear end output shaft seals (inner axel seals) 98 town and country? What fluid goes back in?

I assume you mean trans axle seals in front.
You have to remove the drive axles,best done on a lift,not in your driveway.
Trans fluid lubes the Diff,that is in trans.
ATF4 etc,whatever the fluid replaced the original spec, when it was new.

Oct 01, 2010 | 1998 Chrysler Town & Country

1 Answer

4L-60E trans interchange

Sorry it will not work, the internals are the same but the transmission housing has changed. The key distinction of the Later 4L60-E (1997-2006) from the Early 4L60-E (1992-1997) or 4L60 (1990-1992) or 700R4 (1982-1989) is the six-bolt "hex" rear output or tail-housing / adapter pattern. The previous versions featured a four-bolt square bolt pattern at the adapter or tail-housing. Additionally, the removable bell-housing is also another distinguishing feature.

Two-wheel-drive versions have tail-housings and typically a longer output shafts than four-wheel-drive versions, which have various adapter assemblies and a shorter output shaft.

Jan 12, 2010 | 2002 Chevrolet Tahoe

1 Answer

Transmission for 1988, 350, conversion van

A turbo400 trans will bolt up but you will have to change the drive shaft as the output shaft is longer than the 350 trans. There will be no trans exchange with a different type that will fit without some modifications. 

May 17, 2009 | Chevrolet Sportvan Cars & Trucks

1 Answer

Clunk in trans

If this is a 4X4 then the problem is most likely the slip yoke not sliding smoothly on the transfer case output shaft splines. You can correct this bt lubricating the slip yoke splines with Teflon Grease .
If it is a 4X2 then lube the output shaft splines on the back of trans.

Jan 25, 2009 | 2002 Ford F150 Regular Cab

1 Answer

1990 Dodge 250 2wd trans fit 4x4 1988 Ramcharger

if you are talking about the trans no! the 2wd trans has a longer output shaft than the 4x4 you can have the shaft changed so that it can work if you are having trouble finding a trans.

Dec 30, 2008 | 1988 Dodge Ramcharger

1 Answer

Speedometer goes to 0 and trans downshifts

There are 2 speed sensors on the transaxle. One is for vehicle speed and one is for trans output shaft speed. My guess is that you replaced the one for output shaft speed.

Nissan Scope Technician- 10 years with Nissan

Oct 26, 2008 | 1999 Nissan Sentra

Not finding what you are looking for?
1993 Chevrolet K1500 Logo

Related Topics:

81 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides