Question about 2000 Ford Focus

1 Answer

SIDE LIGHT BULBS

ANY ONE KNOW HOW THESE COME OUT, IVE TURNED CLOCKWISE, ANTICLOCKWISE PULLED PUSHED TO NO AVAIL

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 404 Answers

Rae they held in by a clip? or break with long nosed pliers grasp metal side push in and turn left

Posted on Jan 05, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the frontlight bulb for camry 2009


Not a lot of room in there, especially on the battery side, but at the back of the headlight there is a connector that turns anticlockwise a one eighth turn. Pull the connector out and the bulb is in it. The bulb has three prongs and pulls out. I can recommend any of the Sylvania Silver Star type bulbs.

http://www.osram-americas.com/en-us/products/automotive/Pages/default.aspx

Change both of them. I have them in my Lexus ES330 (Camry). When you insert the bulb, hold the glass with a tissue as oil on your hands damages the glass because of the heat. Insert the bulb, insert the connector, turn 1/8 clockwise.

How to replace the headlight bulbs on our car Toyota Camry

Aug 23, 2016 | 2009 Toyota Camry

1 Answer

How to remove lightbulb?


There are several different types.
Some, usually the larger ones, have to be pushed in and then turned counter-clockwise, then pilles out.
Others, typically the smaller ones, are simply pulled straight out.
Then there are the ones that are installed in removable sockets. These sockets have to be removed from the back of the light, and then the bulbs are removed from the holder

Sep 23, 2015 | Cars & Trucks

1 Answer

Toyota highlander rear side marker bulb replacement


In the rear compartment, there are little access doors that enable you to the four main bulbs for your tail light assembly. The small marker bulb is not among them, you have to remove the entire housing assembly from the car to gain access to the marker bulb. You should see two bolts that are gold in color, remove the nuts from there being careful not to drop them. Once they are removed you need to pull the tail light off the car. Now be warned, if you have an older highlander chances are that rubber gasket seal that keeps water away from the bulbs will be stuck to the car frame. You are going to need to some what forcibly play with assembly to get it off. What I did was tap the gold bolts with a socket screw driver and rubber mallet. Beyond that I just pushed and pulled till I pried it loose. Once free, remove the light that has the cable running out the back, look for the small light socket on the lower side, turn counter clockwise and replace the bulb. Never touch the new bulb with your bare hand, always hold it with a clean towel. Again, just don't be discouraged if the housing assembly doesn't pop off the first try. And ignore anyone that tells you that the bumper needs to come off or the interior needs to be peeled back; they are misinformed, this will work on the 2001-2007 highlander.

Jan 06, 2013 | Cars & Trucks

1 Answer

How do i turn on the radio in a ls400 1998


The Nakamichi radio in the 1998 Lexus LS400 is turned on by pressing the large round button on the radio in. This same button also controls the volume by turning it clockwise or anticlockwise. The radio will use the same audio input that it used when it was turned off. The input can be changed using the series of buttons on the right side of the radio, tape, cd, fm, am.

May 24, 2012 | 1998 Lexus LS 400

1 Answer

My right side turn signal cuircut works but my left side doesnt ive checked the light bulbs but they're all good.


if hazard lights are ok and you can see all are working, you can tell that your signal lever switch is broken.

Nov 18, 2011 | Cars & Trucks

1 Answer

My left brake light is out, according to the officer who pulled me over, I have a replacement bulb, how do I put it in?


Inspect/Replace Bulbs used in most other lighting fixtures fit into sockets and are held in place by spring tension or mechanical force.
f19-42.gif Common type of automotive bulbs. Bulbs are coded with numbers for replacement purposes. Bulbs with different code numbers might appear physically similar but have different wattage ratings.
There are two basic construction designs for exterior lights: those in which the lens is removed and then the bulb removed from the front, and those in which the light assembly must first be removed, then the socket from the back of the assembly, and finally the bulb from the socket.
  • Removing the lens from the latter type assembly could cause serious damage to the reflector due to dust and other contaminants.
  • Wiping the reflector surface to clean it can also seriously reduce the light's brightness. Therefore, do not remove the lens from light assemblies in which the socket and bulb are removed from the back of the assembly.
  • The bulbs are held in their sockets in a number of ways.
  • Some bulbs are simply pushed into and pulled out of their sockets, and some are screwed in and out.
  • To release a bayonet-style bulb from its socket, the bulb is pressed in and turned counterclockwise.
  • The blade-mount style is removed by pulling the bulb off the mounting tab, then turning the bulb and removing it from the retaining pin.
  • To replace a bulb, remove the bulb accordingly from its socket, and insert a new bulb.

Jan 19, 2011 | 2008 Jeep Compass

1 Answer

Need to replace front turn signal bulb


I have written up a proceedure for my 2005. It should still work for a 2007. I also have a bulb list at the end. Your owners manual also gives a good discription on how to remove the head light. Unfortunally, the head light assembley has to be pulled out to reach the back side of the front turn signal. Hope this helps...

Todd.

Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, place the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)

Dec 03, 2010 | 2007 Chevrolet Uplander

1 Answer

How to replace headlight on passenger side for chevy uplander 2005?


Chevy Uplander (2005) Headlight bulb or turn signal replacement:


It is important to ensure all lights are working for the safety of you and others on the road.


Headlight:

In order to gain access to the head light bulbs, the headlight assembly must be removed. There no easy way to gain access to the lamps with the assembly installed. Open hood. Use 10mm wrench to remove faster on top of the light assembly closest to the rubber hood rest. You then need to remove the silver looking pin near the grill. This pin is snapped in place. Rotate counter clockwise and then pull pin straight out. The light assembly will now have to be pulled past the front header panel near the grill. Use care as the light is pulled past the grill panel. When you have this done there is one more fastener holding the light to the vehicle. On the far out side edge of the light near the fender panel, there is a ball socket fastener holding the light to the vehicle internal frame. Pull straight forward to pull the ball pin out of the socket. It will take a lot of force, but be careful as you apply force and pull light out forward. My light took some wiggling up and down, left and right until the ball released. Once the light is out, the lights are accessible. Both the normal and high beam light sockets rotate counter clockwise to remove from the headlight housing. There is a very tight detent in the counter clock rotation which took a fair amount of force. Once it "clicks" past that point during rotation, the light socket was able to be pulled from the light housing. The light bulb pulls straight out of the socket. Please use a clean towel or gloves to protect your fingers. Bulbs can sometimes crack and cut your fingers. Also, when you install the new lamps, use a towel or cloves as not to get oil on the glass which can cause uneven heating of the glass and crack it under use.


With the light assembly out, it is now easy to reach down into the vehicle to change the turn signal. This lamp is colored since the turn signal lens is clear.


Once bulbs are replaced, please test them before reassembly just in case of any issues. The headlight assembly ball socket will snap back into place easy. Once that is in, press the rest of the light back to its normal place. When the holes are lined up, please the silver colored rod back into its slots all the way down the inside of the light assembly. It then can be rotated and locked back into place. Reinstall the 10mm bolt on top of the light assembly near the rubber hood rest. Again check the lights to insure nothing is out of order.


Rear Lights:

To gain access to the bulbs to the real light assemblies, you must remove the light housings. Open up the rear hatch. Use a T30 Torex screwdriver and remove the two screws on the inside of light. Once those are out, the light assembly can be pulled out slightly from the vehicle. On the side of the van, the light assembly is held in place by two snap fasteners. Pull the light towards the rear of the vehicle to disengage the outside edge fasteners. Once done, the light assembly will be loose and the bulb sockets are accessible. They rotate counter clockwise release from the housing. The bulbs themselves pull straight out of the socket. Please use a towel to protect your hands and to make sure no oil gets on the bulb surface. Once done, reinstall the light assembly by first lining up the two plastic fasteners on the outside edge to the vehicle panel and press the light assembly to the vehicle. Reinstall the two screws and test light. Be sure to have someone press the brake for you to ensure your brake light works.



Bulbs:

Front:


Low beam/ high beam lights: (12362LL) Phillips (H11LL)

Front Turn Signal: 4157NAK amber color

Corner marker lamp: 194FH4 clear


Rear:

Brake/turn light: 4157LL (clear lamp)

Lower back up light and top running light: 3057XX (Wagner) (clear lamp)


Oct 01, 2010 | 2006 Chevrolet Equinox

1 Answer

Trunk light burned out in 2003 Chevy Monte Carlo/ How do I replac


usually they are bayonet bulbs that just pull out. Some have to be pushed in slightly & rotated counter clockwise, These bulbs are usually the bigger ones.

Feb 17, 2009 | 2003 Chevrolet Monte Carlo

1 Answer

Tail lights 99 jeep grand cherroke limited


have you checked the bulb sockets to see if they are burnt or corroded sometime i see that the plastic melts around the contacts where the socket twists into the housing. if your lucky you might get away with replacing just the socket for the brake/running light bulb. but if it is too melted your most likely going to need a new housing

Jan 06, 2009 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Ford Focus Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

61249 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Fordexpert

Level 3 Expert

5331 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...