Question about 2000 Saab 9-3 Viggen

1 Answer

9.3 wont start

Engine turns over but wont fire .just replaced clutch for 1500$ my patience is wearing thin

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Checked spark its good went after fuses all good hit bottom of gas tank with rubber mallet and it started almost positive its the fuel pump

Posted on Dec 30, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My2002 sierra with a4.8 with a good battery, all my dash lights and cd player come on but the truck doesnt turn over right away sometimes it takes 5-10 minutes 2 start of repetitively turning key over


battrey is good but truck makes no sound and wont even click

www.cargurus.com > Questions > Chevrolet > S-10

CarGurusbattrey is good but truck makes no sound and wont even click ... Asked by Jennifer May 15, 2013 at 03:21 PM about the 2002 ... quite obviously the amps aren't getting through~ how do you know the battery is "good". the date ... If it turns over your power and starter are good but the ignition circuit ... Used GMC Sierra 1500".Missing: a4

Intermittant Failure to Start : Chevrolet Silverado 1500 ...

repairpal.com > Problems > Chevrolet > Silverado 1500
first start engine turns over alot. 2000 Chevrolet Silverado 1500. Hard start. When starting my truck it often takes two or three attempts. It kicks over but does not ...Missing: a4

Chevy Silverado and GMC Sierra Starting Problems - Car Forums at ...

forums.edmunds.com > Chevrolet > Chevrolet Silverado 1500

Oct 20, 2008 - 30 posts - ‎19 authors
i got a 2001 silverado 1500 and it wont start it turns over and fires and .... Put the key in and the truck barely starts due to the battery being weak. .... If it was really 8, the lights would be dim? .... I have a 2002 GMC Sierra 4.3L 2WD. ... I bled the fuel filter looking for air, but good fuel came out the top bleede ...Missing: a4

Jan 01, 2016 | 2002 GMC Sierra 1500

1 Answer

Installed new clutch set and now it wont start


Did you check the computer for trouble codes ?
Did you by chance move the crank sensor ??

Jul 02, 2012 | 1994 Jeep Wrangler

2 Answers

Changed manual clutch in a 2000 dodge ram 1500 2wd v6 truck got it back together now it turns over but won't crank


Do you mean that the engine will not fire or run? If that is what you mean, When you replaced the clutch you may have damaged the Crank shaft position sensor. It is located on the passengers side of the engine. where the Bell housing and engine block are bolted together, Just above where the exhaust manifold and exhaust pipe meet. It is bolted to the engine block with 2 bolts. If you do not know it is there and even if you do it is easy to damage.

Jan 26, 2012 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

Glow plug light not coming on, on dash. Engine turning over but not starting. Have never had any trouble starting before. The fan belt has been screeching for about 30 seconds for the last few weeks when...


Check fuses to see if there are busted ones. Then check heater plugs if good. Heater relay included in check. Engine wont fire if the air inside the chamber is cold. Then check fan belts for wear, replace if necessary.

Nov 29, 2009 | Volkswagen Golf Cars & Trucks

1 Answer

1996 DODGE RAM 1500 LOSES OIL PRESSURE AFTER WARMED UP FINE WHEN FIRST STARTED WHY?


There are several reasons. The oil viscosity can make a difference and if the oil is contaminated with fuel. Wear in the oil pump and all of your bearings starting with the main crankshaft bearings and the connecting rod bearings. The wrong or bad oil filter.
When cold oil flows it plugs leaking bearings and oil gears. When the oil warms, the wear in the bearings (gaps) can't hold back the thin oil and the pressure drops. If the bearings are replaced before the crank and cam are damaged, the pressure will be maintained.

Jul 07, 2009 | 1998 Dodge Ram 1500 4WD

1 Answer

My car wont start


You need a new engine. There has been quite a few cases of rod bearing failures on these engines. If the engine is left idling, the oil pressure drops as it gets hot and thin. If there was significant wear already inside the engine, that wear would accelerate rapidly with low oil pressure and the bearings would spin in their saddles.

May 20, 2009 | 1995 Pontiac Bonneville

1 Answer

My 01 chevy silverado 1500 won't start MOST of the time.


There is a clutch safety switch under the dash. When you press the clutch it presses the switch. You might try replacing that and see if that fixes your problem. This would cause it not to start and everything would still come on.

Jan 26, 2009 | 2001 Chevrolet Silverado 1500

1 Answer

93 honda prelude dohc vtec engine will not can be push started


Sounds like you accidently pulled the thin wire from you starter motor. Look at the connections at the end of the solenoid, mounted on starter motor.The thick red wire is Battery + next to that connection is a smaller male push- on terminal, locate loose wire (thin) in the same area and reconnect to male push-on terminal on solenoid or check if earth cable between body/battery to engine wasnt removed in the process.Also some vehicles you have to engage the clutch before starting, check for a switch located on clutch pedal where master cylinder connects to clutch pedal (Is clutch switch mounted and wiring connected?)

Jan 03, 2009 | 1993 Honda Prelude

Not finding what you are looking for?
2000 Saab 9-3 Viggen Logo

158 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saab Experts

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

yadayada
yadayada

Level 3 Expert

60769 Answers

rgbypoet

Level 2 Expert

161 Answers

Are you a Saab Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...