Question about 2005 BMW X5

1 Answer

Keyless entry will not operate nor can i crank 2002 escalade

It started with keyless would not operate but i could crank now i can't crank nor does keyless work

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 126 Answers

I think the battery in this key is dead. the ignition is suppose to recharge the key through normal use. if the key is not used often enough, it will lose its charge and need to be reprogrammed by the dealer.

try your other key to see if it will work. once you get them both working again, make sure to rotate them every 6 months so both maintain a full charge.

if you find the ignition is not recharging the key, then a trip to the dealer will be necessary to get it fixed. you might still be covered by the 4 year bumper to bumper warranty as long as you are under 50,000 miles regardless if you bought it new or used at a non BMW dealership or private sale.

good luck

Posted on Jan 17, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find out if vehicle has remote start feature ? all functions on key fob work except engine crank even park lights flash indicating remote start feature . maybe a fuse blown or not in place.


How to check if your GM car is equipped with factory keyless ...

blog.remotesandkeys.com/.../How-to-check-if-your-GM-car-is-equipped...
Aug 25, 2011 - Many, but not all GM vehicles, are equipped with factory keyless entry. ... If not, and you want to have remote keyless entry, go to an alarm shop or Best .... Your other option is to locate the aftermarket receiver under the dash and ... start but need programmed or how can i check if i have remote start installed.

Remote Start ' Vehicle Features ' Official Ford Owner Site

owner.ford.com/.../vehicle-features/.../remote-start-...

Ford Motor CompanyIf your vehicle has automatic climate control, you can configure it to begin operating when you remote start your vehicle. A manual climate control system will run ...

Factory Remote Start Installed? - Chevrolet Forum - Chevy ..


Jan 14, 2016 | Cars & Trucks

1 Answer

What if i dont have the keyless entry key


YES your car thinks you have stolen it, The dealers computer will convince it that you did not

Nov 28, 2013 | 2002 Ford F150 Regular Cab

1 Answer

Cannot program keyless following inst on can not get into program mode


is anti theft light flashing?? if so crank engine for one second. leave key in on position until theft light quits flashing. cycle switch to off. try to start engine. if no start, possible fault with keyless entry sensor at key tumbler..

Jan 17, 2013 | 2002 Oldsmobile Silhouette

1 Answer

2004 dodge strtus cranks but no start/ has security light flashing


Operate your keyless entry/alarm on and off a few times then try to start.

Oct 24, 2011 | 2004 Dodge Stratus

1 Answer

Keyless entry is not working


check the releys under the hood play musical releys and find the problem child
munber all the releys 1 - 10 then start playing musical releys

Dec 12, 2009 | Hyundai Motor 2002 Elantra

1 Answer

2000 Lincoln Towncar. Keypad on door will not unlock doors. Interior lights do come on. The last two keys pushed simultaneously will occasionally lock the doors. I am using the code printed on a sticker in...


The driver door module (DDM) is connected on the standard corporate protocol (SCP) communication network. The DDM controls many functions including power windows, power door locks and remote keyless entry. The DDM also communicates with the driver seat module (DSM) to control the power mirror and seat memory functions.
Do you know anything about automotive electronic control modules ?
The driver door module (DDM) receives inputs from the digital transmission range (DTR) sensor, ignition switch, seat switch, window/door lock switches, lighting control module (LCM), keyless entry keypad switch and remote transmitter. The DDM outputs consists of keyless entry keypad switch illumination, power door lock actuators, luggage compartment release solenoid, horn relay, and lighting control module (LCM).
Best thing to do would be to have a factory scan tool hooked up to check for DTC'S diagnostic trouble codes . That should be the first step if it's not programming the code.
  • The doors do not lock/unlock using the keyless entry keypad
  • Keypad.
  • Circuitry.
  • Driver door module (DDM).
  • GO to Pinpoint Test L .

PINPOINT TEST L: THE DOORS DO NOT LOCK/UNLOCK USING THE KEYLESS ENTRY KEYPAD CONDITIONS DETAILS/RESULTS/ACTIONS L1 RETRIEVE THE RECORDED RESULTS FROM BOTH CONTINUOUS AND ON DEMAND SELF TESTS Use the recorded DDM DTCs from the Continuous and On Demand self tests.
  • Are any DTCs recorded?
Yes For DTC B1525, GO to L3 .

For all other DDM DTCs, REFER to the DDM Diagnostic Trouble Code (DTC) Index.

No If the door locks are inoperative, GO to L2 .

If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 .
L2 CHECK THE DOOR LOCK OPERATION Check the door lock operation by depressing a door lock switch.
  • Do the door locks operate?
Yes GO to L3 .

No GO to Pinpoint Test E . L3 MONITOR THE DDM PID KEY_PAD
Scan tool
Monitor the DDM PID KEY_PAD.
  • Are any of the keyless entry keypad switch numbers present?
Yes GO to L4 .

No GO to L5 . L4 CHECK THE KEYLESS ENTRY KEYPAD SWITCH
Keyless Entry Keypad Switch C525
Monitor the DDM PID KEY_PAD.
  • Are any of the keyless entry keypad switch numbers present?
Yes If 1/2, REPAIR Circuit 78 (LB/YE). TEST the system for normal operation.
If 3/4, REPAIR Circuit 79 (LG/RD). TEST the system for normal operation.
If 5/6, REPAIR Circuit 121 (YE/BK). TEST the system for normal operation.
If 7/8, REPAIR Circuit 122 (YE). TEST the system for normal operation.
If 9/0, REPAIR Circuit 123 (RD). TEST the system for normal operation.

No INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry . L5 CHECK THE KEYLESS ENTRY KEYPAD INPUT WITH THE KEYLESS ENTRY KEYPAD SWITCH Monitor the DDM PID KEY_PAD, while depressing all the keyless entry keypad switches one at a time.
  • Are all the keyless entry keypad switches operating correctly?
Yes GO to L9 .

No GO to L6 . L6 CHECK CIRCUIT 797 (LG/VT) FOR VOLTAGE
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, Circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, Circuit 797 (LG/VT), and ground.
  • Are the voltages greater than 10 volts?
Yes GO to L7 .

No REPAIR Circuit 797 (LG/VT). TEST the system for normal operation. L7 CHECK THE KEYLESS ENTRY KEYPAD SWITCH INPUT While monitoring the DDM PID KEY_PAD, momentarily connect a fused (7.5A) jumper wire between positive battery post and keyless entry keypad switch C525 as follows:
    Keypad Button Keyless Keypad Switch C525 Circuit 1/2 Pin 3 78 (LB/YE) 3/4 Pin 4 79 (LG/RD) 5/6 Pin 5 121 (YE/BK) 7/8 Pin 6 122 (YE) 9/0 Pin 1 123 (RD)

  • Are all the keyless entry keypad switch inputs operating correctly?
Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No GO to L8 . L8 CHECK THE KEYLESS ENTRY KEYPAD SWITCH CIRCUITRY FOR AN OPEN
DDM
Measure the resistance between keyless entry keypad switch C525 and DDM as follows:
    Keyless Keypad Switch C525 DDM Circuit Pin 3 C521 Pin 8 78 (LB/YE) Pin 4 C521 Pin 13 79 (LG/RD) Pin 5 C521 Pin 16 121 (YE/BK) Pin 6 C520 Pin 24 122 (YE) Pin 1 C520 Pin 25 123 (RD)

  • Is the resistance less than 5 ohms?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No REPAIR the circuit in question. TEST the system for normal operation. L9 CHECK THE KEYLESS ENTRY KEYPAD BACKLIGHT Depress a key on the keyless entry keypad.
  • Does the keypad illumination operate correctly?
Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No If the keypad illumination does not operate, GO to L10 .

If the keypad illumination is on continuously, GO to L14 . L10 CHECK THE KEYPAD - DDM ACTIVE COMMAND KEYPAD BACKLIGHTING LIGHT ON AND OFF Trigger the DDM active command KEYPAD BACKLIGHTING LIGHT ON and OFF.
  • Does the keypad illumination turn off and on?
Yes INSTALL a new DDM. For additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L11 . L11 CHECK DDM GROUND - JUMPER CIRCUIT 66 (LB) TO GROUND
DDM 522
Connect a fused (7.5A) jumper wire between DDM C522-4, circuit 66 (LB), and ground.
  • Does the keypad illuminate?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L12 . L12 CHECK CIRCUIT 51 (BK/W) FOR OPEN
Keyless Entry Keypad C525
Measure the voltage between keyless entry keypad C525-7, circuit 797 (LG/VT), and ground; and between keyless entry keypad C525-8, circuit 797 (LG/VT), and ground.
  • Are the voltages greater than 10 volts?
Yes GO to L13 .

No REPAIR circuit 797 (LG/VT). TEST the system for normal operation. L13 CHECK CIRCUIT 66 (LB) FOR OPEN Measure the resistance between keyless entry keypad C525-2, Circuit 66 (LB), and DDM C522-4, Circuit 66, (LB).
  • Is the resistance less than 5 ohms?
Yes INSTALL a new keyless entry keypad switch; for additional information, REFER to Keypad-Keyless Entry .

No REPAIR Circuit 66 (LB). TEST the system for normal operation. L14 CHECK THE KEYPAD ILLUMINATION - DDM DISCONNECTED
DDM C522

  • Does the keypad illumination turn off?
Yes INSTALL a new DDM; for additional information, REFER to Section 419-10 . TEST the system for normal operation.

No GO to L15 . L15 CHECK KEYLESS ENTRY KEYPAD FOR SHORT TO GROUND
Keyless Entry Keypad C525

  • Does the keypad illumination turn off?
Yes GO to L16 .

No INSTALL a new keyless entry keypad switch. For additional information, REFER to Keypad-Keyless Entry . TEST the system for normal operation. L16 CHECK CIRCUIT 66 (LB) FOR SHORT TO GROUND Measure resistance between DDM C522-4, circuit 66 (LB), and ground.
  • Is resistance greater than 10,000 ohms?
Yes System OK. CLARIFY the concern with the customer.

No REPAIR circuit 66 (LB). TEST the system for normal operation.

Nov 03, 2017 | Lincoln Town Car Cars & Trucks

1 Answer

Keyless entry wont work 2002 chevy s10


The only way to program them is with a scan tool so you'll need to visit your local dealer to have it done. Here is how it is done.

  1. Install a scan tool.
  2. Use the scan tool in order to access programming: Vehicle Control System/Computer Integrating System/Module Setup/BCM/Program Key Fobs.
  3. Press the START soft key on the scan tool. Important: The scan tool must stay connected until all of the transmitters are programmed.
  4. Press and hold the LOCK button and the UNLOCK button simultaneously on one transmitter. After a delay of 5-10 seconds, the scan tool will indicate that the transmitter is programmed.
  5. Repeat the previous step in order to program up to 4 transmitters.
  6. Remove the scan tool.
  7. Operate the transmitter functions in order to verify correct system operation.

Sep 02, 2009 | 2002 Chevrolet S-10

1 Answer

Honda Civic 2002 keyless entry


inspect and or replace the drivers door lock actuator...

Apr 05, 2009 | 2002 Honda Civic

2 Answers

Keyless door pads


Go to www.customersaskford.com - type in the text box - keyless entry - then press the "ask" button

Jun 21, 2008 | 2002 Mercury Mountaineer

Not finding what you are looking for?

Open Questions:

See all 2005 BMW X5 Questions

2005 BMW X5 Logo

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Anthony Jones
Anthony Jones

Level 2 Expert

128 Answers

Frankie B

Level 2 Expert

65 Answers

Doberman

Level 2 Expert

254 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...