Question about 2002 Isuzu Rodeo

1 Answer

SHOWING CHECK ENGINE"CHECK TRANS,CRUSER SET AND IF SHAKE THE BODY

IS STOP

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 350 Answers

If the Problem is Only the Check Engine Light Being On there are many different possibilities including simply that the gas cap wasn't put on properly the last time in which case you should give it a week and it should go off by itself.
If there are more problems then just the light being on please explain!


Posted on Jan 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a jaguar s type 2000 it writes gearbox fault and is in limp mode funny the fan is noisy to,please help


You must have a check engine light on in your dash. You first need to pull up the code. I will assume your trans is an automatic. If so, when your trans goes into limp mode, if you stop , shut off your motor, and start again, does your car run OK again, till the next time it goes into limp mode. If so you have a bad trans solenoid. Sometimes this solenoid is on the outside of a trans and sometimes it's on the inside. If inside you would have to drop the pan, and valve body, because it's on top of the valve body. The fan is a separate issue. GOOD LUCK FRIEND.

Nov 17, 2014 | Cars & Trucks

1 Answer

Where can i locate chassis number on body on 2005 pt cruser


On a 2.4 PT It's found at the rear of the cylinder block, on a 2.0 it's found on front side of engine block.
There are VIN numbers on the dash board viewed through the screen. On the fire wall can be found the body code plate.
On the T350 manual transaxle the codes can be found on the transaxle end cover and on the G288, it's found on the transaxle bell housing.
Finally, on auto trans, it's found affixed to the trans axle torque converter housing. Have a poke about and you should find what you are looking for. some plates contain partial information, but all should match, as you know.
Hope you find this helpful. Red

May 15, 2014 | 2002 Chrysler PT Cruiser

1 Answer

Hello, I have a 1995 Oldsmobile Achieva 2.3L only after I am driving above 45 mph (OD) gear and then comming to a stop, it starts to shake and sputter then dies out. It drives fine with no problem for the...


this is what is considered a 3 speed overdrive transmission.this sounds like the tcc solenoid is not releasing the lock up portion of the torque converter.this is located in the trans mission(i think).the older ones the connection was on the front outside of the transmission but the pan had to be removed to remove the lock clip that locked it in the trans body inside the transmission.i`m not sure if they have it inside the trans in this year.it could also be a problem with the torque converter itself.have a trans shop check it out or talk to a tranny tech they can tell you more.

May 01, 2011 | Oldsmobile Achieva Cars & Trucks

1 Answer

Engine just started to shake when i come to a stop


check vacuum lines ,fuel filter,egr valve these three usually dont set off a check engine light when they are going bad or minor leak

Feb 01, 2010 | 2004 Chevrolet Avalanche

1 Answer

HOW MUCH IS A REPAIR FOR A 2002 PT CRUSER HEAD GASKET


Strip engine of intake manifold and throttle body.Remove spark plug leads and coils.Remove tappet cover.Clean all surfaces and fit new gasket. Reassemble engine.Sealant $1.50 Courier & tolls $8.00 Gasket valve cover $172.00 Labour $60.00.That was the account I had to pay

Jun 15, 2009 | 2002 Chrysler PT Cruiser

1 Answer

MY 2004 CHRYSLER 300M CHECK ENGINE LIGHT CAME ON AND A P1776 AND P0700 CODES CAME UP, WHAT DO I NEED TO DO??? DEBBIE


p0700 indicates you have trans fault present..p1776 is a trans fault which means solenoid switch valve is latched in low/reverse position..solenoid switch valve is located in valve body of transmission,but for 2001-2004 LH vehicles you need transmission event data read to find out what TRS position the fault set..recommend chrysler dealer for this fault..also build code on solenoid pack in trans must be checked..if in a certain build code range,you replace solenoid pack..not the valve body..valve body must be removed to check build code on solenoid pack..i have seen this problem before..i am a dealer technician, and had one of these fault codes last week and solenoid pack was the problem..solenoid pack is about 375 dollars..total time with diagnostics was about 3 hours..

Jun 13, 2009 | 2003 Chrysler 300M

1 Answer

Vibration from the engine causing the whole car to shake.


sounds like the motor mounts are badley worn or possibly not allinged correctly also check the exhaust for contact with the body, if this is an automatic check your tourqe converter bolts and examine the flywheel with the cover off for out of square or vibration please rate -jeff

Sep 01, 2008 | 1991 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

74 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

61168 Answers

Steve Hurc
Steve Hurc

Level 3 Expert

450 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

21949 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...